Nancy Heylen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nancy Heylen has a total of 133 co-authors. Here are the top co-authors by number of shared publications:
- Katia Devriendt
Imec 3 , Kapeldreef 75, Leuven 3001
3 shared publications - Anne Jourdain
IMEC, Leuven, Belgium
2 shared publications - Eric Beyne
IMEC, Leuven, Belgium
2 shared publications - Fumihiro Inoue
Yokohama National University
2 shared publications - Jaber Derakhshandeh
IMEC, Leuven, Belgium
2 shared publications - Lieve Teugels
IMEC, Leuven, Belgium
2 shared publications
Latest Publications
- Open Access
- 19 February 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (3) , 03SP39
Chemical mechanical polishing for indium bond pad damascene processing
We investigated chemical mechanical polishing (CMP) of indium, with the goal of obtaining indium bond pads for later cryo-3D integration of quantum computing-related chips, through bonding between these bond pads and indium bumps. Higher removal rates were obtained with soft CMP pads than with hard pads. The latter led to deep scratching, while this effect was much more limited for soft pad CMP. On patterned wafers, indium is cleared well in structured areas using soft pad CMP, leading to relatively high-quality indium surfaces inside bond pads, although corrosion might be of some concern. Pattern density uniformity was an important factor for within-die deviation in indium clearing time. Dishing was much more limited than in earlier work on indium polishing, while surface roughness was also found to be relatively limited. The obtained indium damascene bond pads may be suitable for 3D die-to-die and wafer-to-wafer bonding through indium pad-to-bump bonding.
- 19 February 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (3) , 03SP39
Open AccessChemical mechanical polishing for indium bond pad damascene processing
We investigated chemical mechanical polishing (CMP) of indium, with the goal of obtaining indium bond pads for later cryo-3D integration of quantum computing-related chips, through bonding between these bond pads and indium bumps. Higher removal rates were obtained with soft CMP pads than with hard pads. The latter led to deep scratching, while this effect was much more limited for soft pad CMP. On patterned wafers, indium is cleared well in structured areas using soft pad CMP, leading to relatively high-quality indium surfaces inside bond pads, although corrosion might be of some concern. Pattern density uniformity was an important factor for within-die deviation in indium clearing time. Dishing was much more limited than in earlier work on indium polishing, while surface roughness was also found to be relatively limited. The obtained indium damascene bond pads may be suitable for 3D die-to-die and wafer-to-wafer bonding through indium pad-to-bump bonding.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 69-70
3D sequential stacked planar devices on 300 mm wafers featuring replacement metal gate junction-less top devices processed at 525°C with improved reliability
3D sequential integration requires top MOSFETs processed at low thermal budget, which can impair the device reliability. In this work, top junction-less device are fabricated with a maximum processing temperature of 525°C. The devices feature high k /metal replacement gate and low temperature Si:P and SiGe:B 60% raised SD for NMOS and PMOS respectively. Device matching, analog and RF performance of the top tier devices are in-line with state-of-the-art Si technology processed at high temperature (>1000°C). The top Si layer is transferred on CMOS planar bulk wafers with W metal-1 interconnects, using a SiCN to SiCN direct wafer bonding.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 69-70
3D sequential stacked planar devices on 300 mm wafers featuring replacement metal gate junction-less top devices processed at 525°C with improved reliability
3D sequential integration requires top MOSFETs processed at low thermal budget, which can impair the device reliability. In this work, top junction-less device are fabricated with a maximum processing temperature of 525°C. The devices feature high k /metal replacement gate and low temperature Si:P and SiGe:B 60% raised SD for NMOS and PMOS respectively. Device matching, analog and RF performance of the top tier devices are in-line with state-of-the-art Si technology processed at high temperature (>1000°C). The top Si layer is transferred on CMOS planar bulk wafers with W metal-1 interconnects, using a SiCN to SiCN direct wafer bonding.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
In Depth Analysis of 3D NAND Enablers in Gate Stack Integration and Demonstration in 3D Devices
An in-depth analysis of gate stack enhancements that enable multi-Gb 3D NAND products is performed. Alternative charge trapping layer, enhanced tunnel oxide based on the VariOT concept and metal gate with Al2O3 high-k liner have been proposed and evaluated. The most promising solutions were successfully integrated in 3D devices. Integration challenges of the replacement gate approach, required to have metal gate in 3D NAND, are also analyzed and discussed in detail.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
In Depth Analysis of 3D NAND Enablers in Gate Stack Integration and Demonstration in 3D Devices
An in-depth analysis of gate stack enhancements that enable multi-Gb 3D NAND products is performed. Alternative charge trapping layer, enhanced tunnel oxide based on the VariOT concept and metal gate with Al2O3 high-k liner have been proposed and evaluated. The most promising solutions were successfully integrated in 3D devices. Integration challenges of the replacement gate approach, required to have metal gate in 3D NAND, are also analyzed and discussed in detail.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 128-133
3D Stacking Using Bump-Less Process for Sub 10um Pitch Interconnects
In this paper a bump-less process is introduced in order to further scale down the pitch of microbumps. Electrical resistance measurement, Cross section SEM and mechanical characterizations show successful 3D stacking using proposed method.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 128-133
3D Stacking Using Bump-Less Process for Sub 10um Pitch Interconnects
In this paper a bump-less process is introduced in order to further scale down the pitch of microbumps. Electrical resistance measurement, Cross section SEM and mechanical characterizations show successful 3D stacking using proposed method.
- 1 June 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 2380632X,p. 1-3
Integration of a k=2.3 spin-on polymer for the sub-28nm technology node using EUV lithography
In this work we integrate an advanced k=2.3 spin-on polymer at 40nm ½ pitch. K-value restoration techniques are investigated and complete k-value restoration is demonstrated using an in-situ HeH 2 plasma. An EUV compatible stack and a dielectric dual hard mask scheme is developed to pattern trenches with good uniformity and low litho-etch bias. The impact of scaling the dielectric spacing and of direct CMP on time dependent dielectric breakdown is also studied.
- 1 June 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 2380632X,p. 1-3
Integration of a k=2.3 spin-on polymer for the sub-28nm technology node using EUV lithography
In this work we integrate an advanced k=2.3 spin-on polymer at 40nm ½ pitch. K-value restoration techniques are investigated and complete k-value restoration is demonstrated using an in-situ HeH 2 plasma. An EUV compatible stack and a dielectric dual hard mask scheme is developed to pattern trenches with good uniformity and low litho-etch bias. The impact of scaling the dielectric spacing and of direct CMP on time dependent dielectric breakdown is also studied.
- 1 June 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 07431562,p. 109-110
Impact of thinning and through silicon via proximity on High-k / Metal Gate first CMOS performance
3D integration has the potential to alleviate the performance limitations that CMOS scaling is facing provided that it preserves the integrity of both front end and back end devices and constituting materials. The impact of wafer thinning and of the proximity of through silicon via on active devices, back end structures, ring oscillators and mixed signal circuit are reported for the first time for a High-k/Metal Gate first strained CMOS technology with low-k BEOL. The relative stress induced by the STI and the TSV are measured by micro-Raman spectroscopy. The measured impact of the stress on a sensitive DAC circuit is used to define a safe keep out area.
- 1 June 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 07431562,p. 109-110
Impact of thinning and through silicon via proximity on High-k / Metal Gate first CMOS performance
3D integration has the potential to alleviate the performance limitations that CMOS scaling is facing provided that it preserves the integrity of both front end and back end devices and constituting materials. The impact of wafer thinning and of the proximity of through silicon via on active devices, back end structures, ring oscillators and mixed signal circuit are reported for the first time for a High-k/Metal Gate first strained CMOS technology with low-k BEOL. The relative stress induced by the STI and the TSV are measured by micro-Raman spectroscopy. The measured impact of the stress on a sensitive DAC circuit is used to define a safe keep out area.