BMByung Ho Min

Byung Ho Min

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Byung Ho Min has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Airgapless PMSM With Diamond Like Carbon Coating Technology for Torque Improvement

    by Hyungkwan Jang, Woongpyo Hong, Taegyu Lee, Byungho Min

    The goal of this study is to investigate a radial type permanent magnet synchronous motor without airgap using diamond like carbon coating (DLC) technology to maximize the torque and verify the possibility of applying DLC to motor. Since existing motor technologies have limitations in improving torque, a material is introduced which can enhance motor power. The DLC coating used in automotive combustion engines allows the engine to perform well even at very high temperatures and under strong friction conditions. Also, auto transmission oil, which is used as cooling oil for HEV/EV traction motors, was used to minimize the friction between the rotor and the stator and to cool the rotor and stator. Also, effectiveness of drag force and temperature by friction were investigated. As a result, even if the rotor and stator collide due to the vibration generated in the airgap between bearing cap and ball, the motor can rotate without any problems, and the motor torque greatly increases. After the motor rotates at 5,000 r/min, the DLC coating adopted to electric motor is verified.

  • Application of Electrically-Conductive Epoxy in No-Insulation Coils for Controlling Contact Resistance

    by Jeongwoo Seo, Jiyoung Yoon, Seungyong Hahn, Jonghoon Yoon, Wonseok Jang, Seokho Kim, Kihwan Kim, Kideok Sim, Jongho Choi, Jingeun Kim, et al.

    This article presents a partial-depth impregnation method using electrically conductive epoxy composites in high-temperature superconductor (HTS) coils. In a previous study, we proposed a wet winding technique using electrically-conductive epoxy composites to control the contact resistance of no-insulation (NI) HTS coils. In that method, the epoxy composites were applied across the entire contact surface between winding turns, allowing the contact resistance to be controlled by adjusting the mixing ratio of electrically-conductive powder. However, this approach led to significant current degradation due to delamination caused by thermal contraction mismatch between the epoxy composites and the HTS tape. The partial-depth impregnation method addresses this issue by allowing the epoxy composites to penetrate only partway between winding turns, thereby minimizing critical current degradation. In this study, HTS coils were dry-wound with 4.1 mm-wide HTS tape and insulated with 3 mm-wide polyimide tape on each turn. By applying the electrically-conductive epoxy composites to the edge of the HTS coil, the epoxy composite penetrated to a depth of 1.1 mm. This configuration allows the current to bypass through the edge of the insulated coil, providing self-protection characteristics. Additionally, the contact resistance can be controlled by adjusting the mixing ratio of the electrically-conductive powders. The feasibility of the proposed impregnation technique was demonstrated through over-current and sudden-discharge tests on the partial-depth impregnated coils with different mixing ratios of electrically conductive powders.


  • Design and Performance Evaluation of LH2 Cooling System for HTS Motor Electric Propulsion Platform

    by Kihwan Kim, Seongyong Hahn, Byungho Min, Ki-Deok Sim, Seokho Kim

    This study focuses on developing an electric propulsion platform that utilizes liquid hydrogen (LH2) as both fuel and coolant. The cooling system aims to cryogenically cool the rotor of a high-temperature superconductor (HTS) motor with LH2 while supplying the discharged hydrogen to the fuel cell. By omitting an additional cryocooler for the HTS motor, this approach enhances efficiency and overall performance. The research includes the thermohydraulic and structural design of the HTS magnet rotor, incorporating LH2 and a triple tube-magnetic fluid seal. A prototype cooling system was fabricated, and its performance evaluated using liquid nitrogen (LN2) as an alternative refrigerant to ensure safety. LN2 verified the flow and boiling heat transfer characteristics of the HTS rotor cooling system, with the flow rate controlled by the pressure build-up (PBU) method in the LN2 vessel, relying on ambient heat load.

  • Contact Resistance and Over-Current Characteristics of No-Insulation High-Temperature Superconducting Coils Impregnated With an Electrically-Conductive Epoxy

    by Sihyun Park, Seungyong Hahn, Uijong Bong, Jonghoon Yoon, Seokho Kim, Jaehwan Lee, Kideok Sim, Byung Ho Min, Jiho Lee, Hongmin Yang, et al.

    This paper examines the electrical characteristics of no-insulation (NI) high-temperature superconducting (HTS) coils impregnated with an electrically conductive epoxy. The NI winding technique refers to a method of winding HTS coils without insulating materials between the winding turns and is regarded as the most promising method to protect the HTS coils from the quench phenomenon. Thus far, many analytical and experimental studies focusing on the electrical characteristics of NI HTS coils have been conducted. From these studies, the quench tolerance levels of NI HTS coils were verified, and the possibility of using NI HTS coils in high-field-magnet applications was confirmed. In addition, studies have recently attempted to apply NI HTS coils to electrical rotating machines. The use of NI HTS coils as field coils in electrical rotating machines is expected to enhance their thermal/electrical stability, but there may also be technical issues related to charging/discharging delays and mechanical reliability. In this paper, we propose a NI HTS coil impregnated with an electrically-conductive epoxy to resolve these issues. In the proposed method, a commercially available epoxy resin is mixed with electrically conductive particles, after which HTS coils are wet-wound using the electrically conductive epoxy. In addition, it was confirmed in charging/discharging tests and in a quench test that HTS coils manufactured by the proposed method show reduced charging/discharging delay times in conjunction with quench-tolerant characteristics. The results here demonstrate the potential of the proposed electrically conductive epoxy impregnated NI HTS coil for electrical rotating machine applications.