KKKihwan Kim

Kihwan Kim

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kihwan Kim has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Design and Performance Evaluation of a Gas Blow Thermal Coupling for High-Speed HTS Rotors

    by Kihwan Kim, Yubin Kim, Yonghyun Kwon, Seokho Kim

    High-temperature superconducting (HTS) rotating machines have emerged as promising candidates for next-generation electric propulsion and energy systems requiring high efficiency and power density. One of the major technical challenges in such systems is realizing cryogenic cooling of the rotating components—especially the field rotor—without mechanical contact with stationary cooling sources such as cryocoolers or heat exchangers. To address this challenge, this paper proposes a novel non-contact thermal coupling structure, referred to as the Gas Blow Coupling (GBC). The GBC enables cryogenic cooling by reducing thermal resistance between a stationary cryocooler and a rotating HTS device through a fluid-based thermal medium. The cooling process operates in two stages: in the initial phase, heat is transferred by conduction across a narrow fluid gap to establish minimum operating conditions. In the operational phase, once the rotor begins to spin, forced convection is induced by an impeller attached to the rotor, enhancing heat transfer via fluid circulation. This dual-mode cooling approach simplifies the system architecture while maintaining thermal reliability under cryogenic conditions. The conceptual design and thermal performance of the GBC are evaluated through numerical simulations, confirming its feasibility as an effective thermal interface for rotating HTS applications.

  • Application of Electrically-Conductive Epoxy in No-Insulation Coils for Controlling Contact Resistance

    by Jeongwoo Seo, Jiyoung Yoon, Seungyong Hahn, Jonghoon Yoon, Wonseok Jang, Seokho Kim, Kihwan Kim, Kideok Sim, Jongho Choi, Jingeun Kim, et al.

    This article presents a partial-depth impregnation method using electrically conductive epoxy composites in high-temperature superconductor (HTS) coils. In a previous study, we proposed a wet winding technique using electrically-conductive epoxy composites to control the contact resistance of no-insulation (NI) HTS coils. In that method, the epoxy composites were applied across the entire contact surface between winding turns, allowing the contact resistance to be controlled by adjusting the mixing ratio of electrically-conductive powder. However, this approach led to significant current degradation due to delamination caused by thermal contraction mismatch between the epoxy composites and the HTS tape. The partial-depth impregnation method addresses this issue by allowing the epoxy composites to penetrate only partway between winding turns, thereby minimizing critical current degradation. In this study, HTS coils were dry-wound with 4.1 mm-wide HTS tape and insulated with 3 mm-wide polyimide tape on each turn. By applying the electrically-conductive epoxy composites to the edge of the HTS coil, the epoxy composite penetrated to a depth of 1.1 mm. This configuration allows the current to bypass through the edge of the insulated coil, providing self-protection characteristics. Additionally, the contact resistance can be controlled by adjusting the mixing ratio of the electrically-conductive powders. The feasibility of the proposed impregnation technique was demonstrated through over-current and sudden-discharge tests on the partial-depth impregnated coils with different mixing ratios of electrically conductive powders.


  • Design and Performance Evaluation of LH2 Cooling System for HTS Motor Electric Propulsion Platform

    by Kihwan Kim, Seongyong Hahn, Byungho Min, Ki-Deok Sim, Seokho Kim

    This study focuses on developing an electric propulsion platform that utilizes liquid hydrogen (LH2) as both fuel and coolant. The cooling system aims to cryogenically cool the rotor of a high-temperature superconductor (HTS) motor with LH2 while supplying the discharged hydrogen to the fuel cell. By omitting an additional cryocooler for the HTS motor, this approach enhances efficiency and overall performance. The research includes the thermohydraulic and structural design of the HTS magnet rotor, incorporating LH2 and a triple tube-magnetic fluid seal. A prototype cooling system was fabricated, and its performance evaluated using liquid nitrogen (LN2) as an alternative refrigerant to ensure safety. LN2 verified the flow and boiling heat transfer characteristics of the HTS rotor cooling system, with the flow rate controlled by the pressure build-up (PBU) method in the LN2 vessel, relying on ambient heat load.

  • Liquid Hydrogen Cooling System for 100 kW-Class HTS Rotor Thermal Design

    by Kihwan Kim, Seongyong Hahn, Byungho Min, Ki-Deok Sim, Yubin Kim, Seokho Kim

    This study introduces a cooling topology for a rotating field coil that integrates the supply of liquid hydrogen (LH 2 ) fuel with the cooling flow path in a High Temperature Superconductor (HTS) motor. The distinguishing feature of this system is the use of cryogenic LH 2 as both refrigerant supplied to the HTS rotor and fuel supplied to a fuel cell. The HTS rotor is fitted with a simple reservoir-shaped heat exchanger and includes both thermal and mechanical design considerations. To supply LH 2 to the high-speed rotating HTS rotor, a cryogenic coupling structure is implemented using a coaxial triple pipe that includes both vacuum insulation layer and Ferro fluid seal. This research describes design process to minimize external heat load and ensure cooling down to 30 K during initial cooling and operation. In addition, thermal analysis is conducted through a commercial FEM analysis in consideration of the rotor components. Based on the design process and results, the fabrication and performance evaluation of the HTS rotor will be conducted.