Z. V. Sazanishvili
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Z. V. Sazanishvili has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Bohdan Tsymbal
National University of Civil Defence of Ukraine
2 shared publications- I. M Matsiuk
Національний технічний університет «Дніпровська політехніка
2 shared publications - Nataliia Rott
Dnipro University of Technology
2 shared publications Кирило Альбертович Зіборов
2 shared publicationsСергій Олександрович Федоряченко
2 shared publicationsAnton Klymenko
Dnipro University of Technology
1 shared publication
Latest Publications
- 12 November 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1063, 85-94
Structural Assessment of AISI 316L Pipes under Internal Pressure Using Analytical and Finite Element Methods
Corrosion-resistant pipes operating under internal pressure are critical components in chemical, energy, and petrochemical industries, where reliability and long-term performance are essential. The present study aims to provide an integrated assessment of material selection and structural performance for pipelines operating in aggressive environments. Austenitic stainless steel AISI 316L was selected based on its superior resistance to chloride-induced corrosion, good weldability, and stable mechanical properties. The required wall thickness was determined analytically using the thin-walled cylinder approach, considering operational pressure and safety factors. To validate the design, a three-dimensional finite element model was developed in Autodesk Inventor, incorporating realistic geometry, welded joints, and boundary conditions. The results show that the calculated wall thickness of 3.76 mm ensures safe operation at an internal pressure of 6 MPa. Finite element analysis revealed that the maximum equivalent stress does not exceed 128 MPa, with a minimum safety factor of 1.56. The maximum displacement was found to be less than 0.1 mm, indicating high structural stiffness and stability. Stress concentrations were localized in geometrically complex regions; however, they remained within allowable limits. The novelty of the study lies in the combined application of analytical and numerical approaches for the validation of pipe design under combined mechanical and environmental loading. The proposed methodology provides a reliable framework for the design and optimization of corrosion-resistant pipelines, ensuring safety, durability, and cost-effectiveness in aggressive operating conditions.
- 12 November 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1063, 85-94
Structural Assessment of AISI 316L Pipes under Internal Pressure Using Analytical and Finite Element Methods
Corrosion-resistant pipes operating under internal pressure are critical components in chemical, energy, and petrochemical industries, where reliability and long-term performance are essential. The present study aims to provide an integrated assessment of material selection and structural performance for pipelines operating in aggressive environments. Austenitic stainless steel AISI 316L was selected based on its superior resistance to chloride-induced corrosion, good weldability, and stable mechanical properties. The required wall thickness was determined analytically using the thin-walled cylinder approach, considering operational pressure and safety factors. To validate the design, a three-dimensional finite element model was developed in Autodesk Inventor, incorporating realistic geometry, welded joints, and boundary conditions. The results show that the calculated wall thickness of 3.76 mm ensures safe operation at an internal pressure of 6 MPa. Finite element analysis revealed that the maximum equivalent stress does not exceed 128 MPa, with a minimum safety factor of 1.56. The maximum displacement was found to be less than 0.1 mm, indicating high structural stiffness and stability. Stress concentrations were localized in geometrically complex regions; however, they remained within allowable limits. The novelty of the study lies in the combined application of analytical and numerical approaches for the validation of pipe design under combined mechanical and environmental loading. The proposed methodology provides a reliable framework for the design and optimization of corrosion-resistant pipelines, ensuring safety, durability, and cost-effectiveness in aggressive operating conditions.
- 30 May 2026
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- No. 40,p. 213-225
Predicting the yield strength of aluminum alloys of the Al–Mg–Sc–Zr system, taking into account grain and disperse strengthening
The modern development of mechanical engineering, transport, and aerospace technology is driving demand for lightweight structural materials with high mechanical properties and corrosion resistance. In this context, Al–Mg aluminum alloys are promising due to their combination of low density, high strength characteristics, and manufacturability. At the same time, during the casting of aluminum alloy billets, there is a tendency for them to form a coarse-grained structure, segregation, and porosity, which negatively affects the yield strength. Therefore, it is important to develop approaches to controlling the microstructure and predicting the mechanical properties of cast alloys. The aim of this work is to study the patterns of formation of the mechanical properties of Al–Mg alloys, microalloyed with Sc and Zr and modified with SiC nanoparticles, as well as to develop a combined approach to predicting the yield strength, taking into account the main strengthening mechanisms. The object of the study is to predict the yield strength of Al–6Mg alloys in different structural states, namely after casting, thermal and thermo-mechanical treatment. Experimental studies included metallographic analysis, scanning electron microscopy with EDS, and tensile testing. It was shown that the initial cast alloy has a coarse-grained structure (400…500 μm) and a yield strength of 150…200 MPa. Microalloying with Sc and Zr ensures the formation of Al₃(Sc,Zr) particles, grain refinement to 250…300 μm, and an increase in σt to 270…310 MPa. The additional introduction of SiC nanoparticles in combination with thermal and thermo-mechanical treatment allows the grain size to be reduced to 100…150 μm and the yield strength to be increased to 350…400 MPa. A combined approach was used to predict σt, taking into account grain, solid solution, dispersion, and deformation strengthening. The calculated values of the yield strength are in good agreement with the experimental ones (the deviation does not exceed 5…7%). The results obtained confirm the possibility of using microstructural parameters to predict the mechanical properties of cast aluminum alloys and can be applied at the stage of designing new materials and technological modes.
- 30 May 2026
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- No. 40,p. 213-225
Predicting the yield strength of aluminum alloys of the Al–Mg–Sc–Zr system, taking into account grain and disperse strengthening
The modern development of mechanical engineering, transport, and aerospace technology is driving demand for lightweight structural materials with high mechanical properties and corrosion resistance. In this context, Al–Mg aluminum alloys are promising due to their combination of low density, high strength characteristics, and manufacturability. At the same time, during the casting of aluminum alloy billets, there is a tendency for them to form a coarse-grained structure, segregation, and porosity, which negatively affects the yield strength. Therefore, it is important to develop approaches to controlling the microstructure and predicting the mechanical properties of cast alloys. The aim of this work is to study the patterns of formation of the mechanical properties of Al–Mg alloys, microalloyed with Sc and Zr and modified with SiC nanoparticles, as well as to develop a combined approach to predicting the yield strength, taking into account the main strengthening mechanisms. The object of the study is to predict the yield strength of Al–6Mg alloys in different structural states, namely after casting, thermal and thermo-mechanical treatment. Experimental studies included metallographic analysis, scanning electron microscopy with EDS, and tensile testing. It was shown that the initial cast alloy has a coarse-grained structure (400…500 μm) and a yield strength of 150…200 MPa. Microalloying with Sc and Zr ensures the formation of Al₃(Sc,Zr) particles, grain refinement to 250…300 μm, and an increase in σt to 270…310 MPa. The additional introduction of SiC nanoparticles in combination with thermal and thermo-mechanical treatment allows the grain size to be reduced to 100…150 μm and the yield strength to be increased to 350…400 MPa. A combined approach was used to predict σt, taking into account grain, solid solution, dispersion, and deformation strengthening. The calculated values of the yield strength are in good agreement with the experimental ones (the deviation does not exceed 5…7%). The results obtained confirm the possibility of using microstructural parameters to predict the mechanical properties of cast aluminum alloys and can be applied at the stage of designing new materials and technological modes.
- Open Access
- 9 December 2025
- Published by Publishing House Helvetica (Publications) in Електротехнічні та інформаційні системи
- No. 108,p. 41-46
МЕТОДОЛОГІЯ КОНТРОЛЮ ЯКОСТІ МАТЕРІАЛІВ ПРОМИСЛОВИХ ЕНЕРГЕТИЧНИХ ВИРОБІВ У КОНТЕКСТІ ПРОМИСЛОВОГО ДИЗАЙНУ
Мета дослідження полягає у розробленні комплексної методології контролю якості матеріалів промислових енергетичних виробів у контексті промислового дизайну з урахуванням вимог міжнародних стандартів ISO та сучасних цифрових технологій. Методологія дослідження базується на використанні математичного апарату багатокритеріальної оптимізації, статистичних методів репрезентативного відбору зразків, теорії надійності (розподіл Вейбулла, імовірнісні моделі безвідмовної роботи), а також цифрових методів діагностики: сенсорних систем, машинного зору, комп’ютерного моделювання та технології цифрових двійників з урахуванням відповідності матеріалів та виробів міжнародним стандартам ISO/IEC, зокрема у сфері електробезпеки, екологічності та довготривалої експлуатаційної придатності.Наукова новизна дослідження полягає у поєднанні матеріалознавчих підходів до контролю якості з принципами промислового дизайну, що дає змогу розширити класичне поняття якості за рахунок інтеграції ергономічних, енергоефективних та безпекових критеріїв. Запропоновано концепцію переходу від реактивного до проактивного управління якістю, а саме проводити прогнозування дефектів на стадії проєктування виробу.
- 9 December 2025
- Published by Publishing House Helvetica (Publications) in Електротехнічні та інформаційні системи
- No. 108,p. 41-46
Open AccessМЕТОДОЛОГІЯ КОНТРОЛЮ ЯКОСТІ МАТЕРІАЛІВ ПРОМИСЛОВИХ ЕНЕРГЕТИЧНИХ ВИРОБІВ У КОНТЕКСТІ ПРОМИСЛОВОГО ДИЗАЙНУ
Мета дослідження полягає у розробленні комплексної методології контролю якості матеріалів промислових енергетичних виробів у контексті промислового дизайну з урахуванням вимог міжнародних стандартів ISO та сучасних цифрових технологій. Методологія дослідження базується на використанні математичного апарату багатокритеріальної оптимізації, статистичних методів репрезентативного відбору зразків, теорії надійності (розподіл Вейбулла, імовірнісні моделі безвідмовної роботи), а також цифрових методів діагностики: сенсорних систем, машинного зору, комп’ютерного моделювання та технології цифрових двійників з урахуванням відповідності матеріалів та виробів міжнародним стандартам ISO/IEC, зокрема у сфері електробезпеки, екологічності та довготривалої експлуатаційної придатності.Наукова новизна дослідження полягає у поєднанні матеріалознавчих підходів до контролю якості з принципами промислового дизайну, що дає змогу розширити класичне поняття якості за рахунок інтеграції ергономічних, енергоефективних та безпекових критеріїв. Запропоновано концепцію переходу від реактивного до проактивного управління якістю, а саме проводити прогнозування дефектів на стадії проєктування виробу.
- Open Access
- 9 December 2025
- Published by Publishing House Helvetica (Publications) in Електротехнічні та інформаційні системи
- No. 108,p. 47-54
ПРИНЦИПИ ПРОМИСЛОВОГО ДИЗАЙНУ ДЛЯ ЗАБЕЗПЕЧЕННЯ ЯКОСТІ ЕЛЕКТРОЕНЕРГЕТИЧНОЇ ПРОДУКЦІЇ
Мета дослідження полягає у розробленні комплексної методології контролю якості матеріалів промислових енергетичних виробів у контексті промислового дизайну з урахуванням вимог міжнародних стандартів ISO та сучасних цифрових технологій.Методологія дослідження ґрунтується на поєднанні інженерного моделювання, статистичного аналізу та цифрових технологій контролю. Застосовано багатокритеріальну оптимізацію, що дає змогу одночасно оцінювати технічні, екологічні та ергономічні показники промислових енергетичних виробів. Якість матеріалів досліджується на основі статистично обґрунтованого відбору зразків із побудовою довірчих інтервалів для характеристик міцності та довговічності. Надійність оцінюється за допомогою імовірнісних моделей безвідмовної роботи, що дає змогу прогнозувати тривалість служби й інтенсивність відмов у різних умовах експлуатації. Верифікація результатів здійснюється із залученням сенсорних систем для моніторингу робочих параметрів, методів машинного зору для виявлення дефектів і цифрових двійників, які інтегрують аналіз конструкційних, теплових та екологічних характеристик. Особливу увагу приділено відповідності матеріалів і виробів міжнародним стандартам ISO та IEC, які регламентують електробезпеку, екологічність, ремонтопридатність і довготривалу експлуатаційну придатність.Наукова новизна роботи полягає у формуванні єдиної науково обґрунтованої методології інтеграції принципів промислового дизайну в електроенергетичне обладнання, яка одночасно враховує енергоефективність, довговічність, екологічний вплив, ергономіку та безпеку. Запропонований підхід базується на багатокритеріальній оптимізації із застосуванням Парето-аналізу, що дає змогу отримувати набір компромісних рішень замість пошуку єдиного мінімуму. Уперше поєднано матеріалознавчі показники, методи оцінки життєвого циклу (LCA) та цифрові двійники для прогнозування експлуатаційних дефектів і визначення довговічності обладнання ще на стадії проєктування. Методологія переносить акцент із реактивного на проактивне управління якістю та узгоджує промисловий дизайн із міжнародними стандартами ISO/IEC і сучасними європейськими регламентами ESPR, що забезпечує відповідність продукції сучасним вимогам енергоефективності, екологічності та стійкості.
- 9 December 2025
- Published by Publishing House Helvetica (Publications) in Електротехнічні та інформаційні системи
- No. 108,p. 47-54
Open AccessПРИНЦИПИ ПРОМИСЛОВОГО ДИЗАЙНУ ДЛЯ ЗАБЕЗПЕЧЕННЯ ЯКОСТІ ЕЛЕКТРОЕНЕРГЕТИЧНОЇ ПРОДУКЦІЇ
Мета дослідження полягає у розробленні комплексної методології контролю якості матеріалів промислових енергетичних виробів у контексті промислового дизайну з урахуванням вимог міжнародних стандартів ISO та сучасних цифрових технологій.Методологія дослідження ґрунтується на поєднанні інженерного моделювання, статистичного аналізу та цифрових технологій контролю. Застосовано багатокритеріальну оптимізацію, що дає змогу одночасно оцінювати технічні, екологічні та ергономічні показники промислових енергетичних виробів. Якість матеріалів досліджується на основі статистично обґрунтованого відбору зразків із побудовою довірчих інтервалів для характеристик міцності та довговічності. Надійність оцінюється за допомогою імовірнісних моделей безвідмовної роботи, що дає змогу прогнозувати тривалість служби й інтенсивність відмов у різних умовах експлуатації. Верифікація результатів здійснюється із залученням сенсорних систем для моніторингу робочих параметрів, методів машинного зору для виявлення дефектів і цифрових двійників, які інтегрують аналіз конструкційних, теплових та екологічних характеристик. Особливу увагу приділено відповідності матеріалів і виробів міжнародним стандартам ISO та IEC, які регламентують електробезпеку, екологічність, ремонтопридатність і довготривалу експлуатаційну придатність.Наукова новизна роботи полягає у формуванні єдиної науково обґрунтованої методології інтеграції принципів промислового дизайну в електроенергетичне обладнання, яка одночасно враховує енергоефективність, довговічність, екологічний вплив, ергономіку та безпеку. Запропонований підхід базується на багатокритеріальній оптимізації із застосуванням Парето-аналізу, що дає змогу отримувати набір компромісних рішень замість пошуку єдиного мінімуму. Уперше поєднано матеріалознавчі показники, методи оцінки життєвого циклу (LCA) та цифрові двійники для прогнозування експлуатаційних дефектів і визначення довговічності обладнання ще на стадії проєктування. Методологія переносить акцент із реактивного на проактивне управління якістю та узгоджує промисловий дизайн із міжнародними стандартами ISO/IEC і сучасними європейськими регламентами ESPR, що забезпечує відповідність продукції сучасним вимогам енергоефективності, екологічності та стійкості.
- 8 December 2025
- Published by Oles Honchar Dnipropetrovsk National University in System design and analysis of aerospace technique characteristics
- Vol. 37 (2) , 3-13
COMPREHENSIVE ASSESSMENT OF THE IMPACT OF ICING ON SMALL UNMANNED AERIAL VEHICLES
The paper addresses the pressing problem of icing of small unmanned aerial vehicles (UAVs), which typically operate at altitudes up to 1500 m where the presence of supercooled cloud droplets, drizzle, and large supercooled droplets (SLD) formed due to temperature inversions is highly probable. It is shown that the traditional icing-intensity assessment criteria, developed for manned aircraft, do not account for the specific features of small UAVs, such as their relatively low lift margin, limited propulsion thrust, and strict weight-and-size constraints. A new comprehensive approach to evaluating the icing hazard for small UAVs is proposed based on previously developed software and methodological tools. Using a typical Clark YH12 airfoil with a 0.24 m chord length as an example, the icing process was numerically simulated over the following parameter ranges: flight speed V∞ = 30 m/s, ambient temperature T∞ = –1…–15 °C, liquid water content LWC = 0.1…0.8 g/m³, and supercooled droplet diameter dk = 14 μm. Ice accretion shapes were obtained, and nomograms were developed to characterize the mass of ice accumulating on the aerodynamic surface as well as the associated degradation of aerodynamic performance. The results can be used in the design of anti-icing systems for small UAVs and also enable rapid assessment of icing hazards both during pre-flight planning and in-mission operation.
- 8 December 2025
- Published by Oles Honchar Dnipropetrovsk National University in System design and analysis of aerospace technique characteristics
- Vol. 37 (2) , 3-13
COMPREHENSIVE ASSESSMENT OF THE IMPACT OF ICING ON SMALL UNMANNED AERIAL VEHICLES
The paper addresses the pressing problem of icing of small unmanned aerial vehicles (UAVs), which typically operate at altitudes up to 1500 m where the presence of supercooled cloud droplets, drizzle, and large supercooled droplets (SLD) formed due to temperature inversions is highly probable. It is shown that the traditional icing-intensity assessment criteria, developed for manned aircraft, do not account for the specific features of small UAVs, such as their relatively low lift margin, limited propulsion thrust, and strict weight-and-size constraints. A new comprehensive approach to evaluating the icing hazard for small UAVs is proposed based on previously developed software and methodological tools. Using a typical Clark YH12 airfoil with a 0.24 m chord length as an example, the icing process was numerically simulated over the following parameter ranges: flight speed V∞ = 30 m/s, ambient temperature T∞ = –1…–15 °C, liquid water content LWC = 0.1…0.8 g/m³, and supercooled droplet diameter dk = 14 μm. Ice accretion shapes were obtained, and nomograms were developed to characterize the mass of ice accumulating on the aerodynamic surface as well as the associated degradation of aerodynamic performance. The results can be used in the design of anti-icing systems for small UAVs and also enable rapid assessment of icing hazards both during pre-flight planning and in-mission operation.
- Open Access
- 24 November 2025
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Rocket-Space Technology
- Vol. 34 (№3) , 3-8
ЕКСПЕРИМЕНТАЛЬНЕ ДОСЛІДЖЕННЯ АЕРОДИНАМІЧНИХ ХАРАКТЕРИСТИК МОДЕЛЕЙ МАЛИХ ЛІТАЛЬНИХ АПАРАТІВ СХЕМИ «ЛІТАЮЧЕ КРИЛО»
Значний інтерес до малих безпілотних літальних апаратів, які знаходять широке застосування для вирішення таких завдань, як спостереження, забезпечення зв’язку, розвідка та виконання інших спеціалізованих місій як у цивільних так і військових сферах, а також постійно зростаючі вимоги до ефективності таких апаратів, зумовлюють актуальність досліджень, спрямованих на вдосконалення їх аеродинамічних характеристик. Особливістю таких апаратів є робота в діапазоні низьких чисел Рейнольдса (Re ~10⁵…10⁶), що істотно впливає на розвиток прикордонного шару та механізм зриву потоку. У статті наведено аналіз результатів експериментальних досліджень аеродинамічних характеристик моделей малих літальних апаратів за схемою «літаюче крило», побудованих на основі профілів Clark та LRN. Експерименти проведено у дозвуковій аеродинамічній трубі із застосуванням трикомпонентних вагових вимірювань, а також методів візуалізації потоку. Моделі було створено із реалізацією змінної товщини профілю крила за розмахом, застосуванням стрілоподібності та V-подібності, гребеневих законцовок та виготовлено методом 3D-друку. Встановлено, що для обох моделей характерне утворення відривного пузиря вже за малих кутів атаки, що призводить до зростання лобового опору. Порівняльний аналіз залежностей підйомної сили, опору та аеродинамічної якості від кута атаки показав, що модель із утворюючим профілем Clark демонструє вищу аеродинамічну якість, в той час як модель із профілем LRN має кращу стійкість до зриву потоку. Отримані результати мають практичне значення для оптимізації геометрії малих БПЛА, підвищення їх енергоефективності, тривалості польоту та надійності також в умовах турбулентності та поривів вітру. Також вони можуть бути використані для верифікації чисельних методів моделювання обтікання та розробки нових конструктивних рішень у сфері експериментальної аеродинаміки.
- 24 November 2025
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Rocket-Space Technology
- Vol. 34 (№3) , 3-8
Open AccessЕКСПЕРИМЕНТАЛЬНЕ ДОСЛІДЖЕННЯ АЕРОДИНАМІЧНИХ ХАРАКТЕРИСТИК МОДЕЛЕЙ МАЛИХ ЛІТАЛЬНИХ АПАРАТІВ СХЕМИ «ЛІТАЮЧЕ КРИЛО»
Значний інтерес до малих безпілотних літальних апаратів, які знаходять широке застосування для вирішення таких завдань, як спостереження, забезпечення зв’язку, розвідка та виконання інших спеціалізованих місій як у цивільних так і військових сферах, а також постійно зростаючі вимоги до ефективності таких апаратів, зумовлюють актуальність досліджень, спрямованих на вдосконалення їх аеродинамічних характеристик. Особливістю таких апаратів є робота в діапазоні низьких чисел Рейнольдса (Re ~10⁵…10⁶), що істотно впливає на розвиток прикордонного шару та механізм зриву потоку. У статті наведено аналіз результатів експериментальних досліджень аеродинамічних характеристик моделей малих літальних апаратів за схемою «літаюче крило», побудованих на основі профілів Clark та LRN. Експерименти проведено у дозвуковій аеродинамічній трубі із застосуванням трикомпонентних вагових вимірювань, а також методів візуалізації потоку. Моделі було створено із реалізацією змінної товщини профілю крила за розмахом, застосуванням стрілоподібності та V-подібності, гребеневих законцовок та виготовлено методом 3D-друку. Встановлено, що для обох моделей характерне утворення відривного пузиря вже за малих кутів атаки, що призводить до зростання лобового опору. Порівняльний аналіз залежностей підйомної сили, опору та аеродинамічної якості від кута атаки показав, що модель із утворюючим профілем Clark демонструє вищу аеродинамічну якість, в той час як модель із профілем LRN має кращу стійкість до зриву потоку. Отримані результати мають практичне значення для оптимізації геометрії малих БПЛА, підвищення їх енергоефективності, тривалості польоту та надійності також в умовах турбулентності та поривів вітру. Також вони можуть бути використані для верифікації чисельних методів моделювання обтікання та розробки нових конструктивних рішень у сфері експериментальної аеродинаміки.
- 25 September 2024
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 364, 73-78
Adhesion of Meta-Aramid Coatings to Metal Substrates
The paper presents experimental investigations of the adhesive properties of meta-aramid coatings applied to metal substrates of different types. The increased adhesion ability of meta-aramid coatings to copper substrates was found in comparison with other metals and alloys used as structural materials. The dependence of the strength of the adhesive bond of the meta-aramid coating on the surface roughness at various concentrations of the polymer solution has been determined.
- 25 September 2024
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 364, 73-78
Adhesion of Meta-Aramid Coatings to Metal Substrates
The paper presents experimental investigations of the adhesive properties of meta-aramid coatings applied to metal substrates of different types. The increased adhesion ability of meta-aramid coatings to copper substrates was found in comparison with other metals and alloys used as structural materials. The dependence of the strength of the adhesive bond of the meta-aramid coating on the surface roughness at various concentrations of the polymer solution has been determined.
- Open Access
- 21 October 2023
- Published by SHEE Prydniprovska State Academy of Civil Engineering and Architecture in Physical Metallurgy and Heat Treatment of Metals
- No. 2 (101),p. 73-78
INVESTIGATION OF THE STRUCTURE AND PROPERTIES OF FERROUS NICKEL ALLOYS AFTER MOLDING BY SELECTIVE LASER MELTING
Problem statement. The selective laser melting method is a promising technology for the production of parts from heat-resistant alloys. Traditional methods of manufacturing such parts require additional technological equipment and processing, which increases the time of production preparation and, as a result, to the creation of a large number of raw materials. Selective laser melting allows you to produce parts of a complex configuration without the need for additional equipment. Molding of parts using additive technologies, which ensure a reduction in product preparation time, mechanical processing operations, and an increase in the efficiency of material use. Their application in the technological cycle of manufacturing products is an urgent task today. However, before the introduction into the technological process of forming products from heat-resistant alloys by the selective laser melting method, it is necessary to carry out a comprehensive analysis of the mechanical and technological characteristics of the material and its microstructure, which affects the final properties of the parts. The purpose of the article. Investigation of the possibility of implementing the selective laser melting method for the production of parts from strong alloys, analysis of the mechanical characteristics of the material, as well as the microstructure, which affects the final properties of the parts. Conclusions. Studies have shown that the selective laser melting method is effective for the production of complex parts from heat-resistant alloys. The obtained data on the mechanical properties after heat treatment of the Inconel718 alloy demonstrate its compliance with the requirements of the AMS 5662 standard and its suitability for working under extreme conditions. In the microstructure, highlighted features are revealed, which are characteristic of the selective laser melting method, as well as the presence of visible tracks and a special texture − elongated grains in the direction of growing parts. Research points to the potential of additive technologies in improving technological processes and properties of alloys for the production of heat-resistant alloy parts.
- 21 October 2023
- Published by SHEE Prydniprovska State Academy of Civil Engineering and Architecture in Physical Metallurgy and Heat Treatment of Metals
- No. 2 (101),p. 73-78
Open AccessINVESTIGATION OF THE STRUCTURE AND PROPERTIES OF FERROUS NICKEL ALLOYS AFTER MOLDING BY SELECTIVE LASER MELTING
Problem statement. The selective laser melting method is a promising technology for the production of parts from heat-resistant alloys. Traditional methods of manufacturing such parts require additional technological equipment and processing, which increases the time of production preparation and, as a result, to the creation of a large number of raw materials. Selective laser melting allows you to produce parts of a complex configuration without the need for additional equipment. Molding of parts using additive technologies, which ensure a reduction in product preparation time, mechanical processing operations, and an increase in the efficiency of material use. Their application in the technological cycle of manufacturing products is an urgent task today. However, before the introduction into the technological process of forming products from heat-resistant alloys by the selective laser melting method, it is necessary to carry out a comprehensive analysis of the mechanical and technological characteristics of the material and its microstructure, which affects the final properties of the parts. The purpose of the article. Investigation of the possibility of implementing the selective laser melting method for the production of parts from strong alloys, analysis of the mechanical characteristics of the material, as well as the microstructure, which affects the final properties of the parts. Conclusions. Studies have shown that the selective laser melting method is effective for the production of complex parts from heat-resistant alloys. The obtained data on the mechanical properties after heat treatment of the Inconel718 alloy demonstrate its compliance with the requirements of the AMS 5662 standard and its suitability for working under extreme conditions. In the microstructure, highlighted features are revealed, which are characteristic of the selective laser melting method, as well as the presence of visible tracks and a special texture − elongated grains in the direction of growing parts. Research points to the potential of additive technologies in improving technological processes and properties of alloys for the production of heat-resistant alloy parts.
- Open Access
- 1 January 2023
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 4(34),p. 61-66
DEVELOPMENT OF HEAT-RESISTANT TRIBOLOGICAL COATINGS BASED ON META-ARAMID
Research on the tribotechnical properties of composite coatings is relevant due to its potential impact on industry, tech-nology, and environmental standards. In the conducted study, tribotechnical properties of composite coatings based on meta-aramid were investigated under dry friction conditions with a load of 1 MPa and a sliding speed of 1 m/s. The results showed that the amount of anti-friction filler significantly influences the friction and wear of coatings. Wear resistance increases up to 20 wt.%, after which the introduction of more filler stabilizes and leads to a decrease in this parameter. The most optimal amount of filler to achieve minimal wear is 20–25 wt.%.It was found that the anti-friction filler forms a lubricating film on the counterface surface, and its parameters depend on the filler concentration. At a high content (up to 20 wt.%), a sharp increase in wear resistance is observed. However, with an increase in the filler concentration above 25 wt.%, a deterioration in strength properties and an increase in the coating's brittleness are observed.Coatings with copper phthalocyanine demonstrated the most effective tribotechnical indicators when the filler concen-trationwas 20–25 wt.%. The wear intensity and friction coefficient of these coatings decreased by 2 and 2.1 times, respectively, compared to the original meta-aramid coating.Additional research on the tribotechnical properties of coatings in liquid environmentswith I-40 lubricant showed that with an increase in the specific load, the wear intensity increases, but this decreases with the addition of the anti-friction filler. At a specific load of 2.5–10 MPa, the wear resistance of the coatings decreased by 1.5–2.5 times, and the friction coefficient decreased by 2.1–3.6 times compared to the meta-aramid coating.The analysis of the results allows determining the optimal amount of filler for meta-aramid coatings as 20 wt.%, consid-ering tribotechnical properties.
- 1 January 2023
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 4(34),p. 61-66
Open AccessDEVELOPMENT OF HEAT-RESISTANT TRIBOLOGICAL COATINGS BASED ON META-ARAMID
Research on the tribotechnical properties of composite coatings is relevant due to its potential impact on industry, tech-nology, and environmental standards. In the conducted study, tribotechnical properties of composite coatings based on meta-aramid were investigated under dry friction conditions with a load of 1 MPa and a sliding speed of 1 m/s. The results showed that the amount of anti-friction filler significantly influences the friction and wear of coatings. Wear resistance increases up to 20 wt.%, after which the introduction of more filler stabilizes and leads to a decrease in this parameter. The most optimal amount of filler to achieve minimal wear is 20–25 wt.%.It was found that the anti-friction filler forms a lubricating film on the counterface surface, and its parameters depend on the filler concentration. At a high content (up to 20 wt.%), a sharp increase in wear resistance is observed. However, with an increase in the filler concentration above 25 wt.%, a deterioration in strength properties and an increase in the coating's brittleness are observed.Coatings with copper phthalocyanine demonstrated the most effective tribotechnical indicators when the filler concen-trationwas 20–25 wt.%. The wear intensity and friction coefficient of these coatings decreased by 2 and 2.1 times, respectively, compared to the original meta-aramid coating.Additional research on the tribotechnical properties of coatings in liquid environmentswith I-40 lubricant showed that with an increase in the specific load, the wear intensity increases, but this decreases with the addition of the anti-friction filler. At a specific load of 2.5–10 MPa, the wear resistance of the coatings decreased by 1.5–2.5 times, and the friction coefficient decreased by 2.1–3.6 times compared to the meta-aramid coating.The analysis of the results allows determining the optimal amount of filler for meta-aramid coatings as 20 wt.%, consid-ering tribotechnical properties.