Haihong Wu
Research Subjects
Haihong Wu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Chuanfeng Wang
CSSC Jiujiang Marine Equipment (Group) Co., Ltd., Jiujiang 332005, China
2 shared publications - Nenghui Wang
Shanghai Aerospace Equipments Manufacture Co., Ltd., Shanghai 200245, China
2 shared publications - Xiao Kang
State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China
2 shared publications - Chengshan Liu
Aerospace Systems Engineering Shanghai, Shanghai 201108, China
1 shared publication - Haiyan Wu
CSSC Jiujiang Marine Equipment (Group) Co., Ltd., Jiujiang 332005, China
1 shared publication - Huiqun Liu
School of Materials Science and Engineering, Central South University, Changsha 410083, China
1 shared publication
Latest Publications
- Open Access
Contact Load on the Current-Carrying Tribological Performance of Copper–Graphite Composites
This study investigates the current-carrying tribological properties and wear mechanisms of copper–graphite composites under varying contact loads. Two copper–graphite composites with different graphite content were prepared using the pressure sintering method. Current-carrying tribological tests were conducted at three distinct contact loads. Scanning electron microscopy, X-ray diffraction, laser confocal microscopy, and pin-on-disk tribological testing were utilized to examine the current-carrying tribological properties and the worn morphologies of the materials. The results indicate that, under the three contact loads, the friction coefficient of the copper–graphite materials ranged from 0.3 to 0.5, the wear rate was on the order of 10−13 m3/(N·m), the average voltage drop varied between 0.7 and 1.6 V, and the average electrical noise ranged from 0.2 to 0.9 mV. The wear mechanism included delamination wear and a minor amount of abrasive wear, and the lubricating film formed on the surface was mainly composed of C, PbO, and CuO. Notably, copper–graphite composites with lower graphite content exhibited superior hardness, electrical conductivity, and relative density compared to those with higher graphite content. At a contact load of 0.31 N, the copper–graphite composite containing 30wt% graphite demonstrated the most favorable current-carrying tribological performance, characterized by the lowest wear rate (1.09 × 10−13 m3/(N·m)), voltage drop (0.943 V), and electrical noise (0.234 mV).
Open AccessContact Load on the Current-Carrying Tribological Performance of Copper–Graphite Composites
This study investigates the current-carrying tribological properties and wear mechanisms of copper–graphite composites under varying contact loads. Two copper–graphite composites with different graphite content were prepared using the pressure sintering method. Current-carrying tribological tests were conducted at three distinct contact loads. Scanning electron microscopy, X-ray diffraction, laser confocal microscopy, and pin-on-disk tribological testing were utilized to examine the current-carrying tribological properties and the worn morphologies of the materials. The results indicate that, under the three contact loads, the friction coefficient of the copper–graphite materials ranged from 0.3 to 0.5, the wear rate was on the order of 10−13 m3/(N·m), the average voltage drop varied between 0.7 and 1.6 V, and the average electrical noise ranged from 0.2 to 0.9 mV. The wear mechanism included delamination wear and a minor amount of abrasive wear, and the lubricating film formed on the surface was mainly composed of C, PbO, and CuO. Notably, copper–graphite composites with lower graphite content exhibited superior hardness, electrical conductivity, and relative density compared to those with higher graphite content. At a contact load of 0.31 N, the copper–graphite composite containing 30wt% graphite demonstrated the most favorable current-carrying tribological performance, characterized by the lowest wear rate (1.09 × 10−13 m3/(N·m)), voltage drop (0.943 V), and electrical noise (0.234 mV).
- Open Access
Friction and Wear Performances and Mechanisms of Graphite/Copper Composites Under Electrical Contact in Marine Environments
Marine environment-induced apparatus failures have led to substantial losses in marine engineering. Graphite/copper composites, known for their excellent electrical conductivity and wear resistance, are extensively utilized in various electric contact devices. However, research on the current-carrying friction and wear behavior of graphite/copper composites in marine environments is still limited. This study investigates the effects of mating materials, graphite content (30 wt.% and 45 wt.%), and electric voltage on the friction and wear mechanisms of graphite/copper composites in seawater. The results show that under seawater coupled with electricity, no mass loss was observed in the 30 wt.% graphite composites after friction tests against different counterparts. Electric voltage (3 V) affects the composite’s damage mechanism, inducing delamination wear, arc erosion and accelerating corrosion. Specifically, the electricity factor promotes oxidation recreations while inhibiting chlorine formation. Notably, when the composite is paired with gold-coated copper, it undergoes electrochemical reactions, leading to the formation of needle-like copper oxide. These oxides alter the surface morphology, elevate the mass of worn composites, and raise the friction coefficient of the tribopair to approximately 0.3, an increase from 0.2.
Open AccessFriction and Wear Performances and Mechanisms of Graphite/Copper Composites Under Electrical Contact in Marine Environments
Marine environment-induced apparatus failures have led to substantial losses in marine engineering. Graphite/copper composites, known for their excellent electrical conductivity and wear resistance, are extensively utilized in various electric contact devices. However, research on the current-carrying friction and wear behavior of graphite/copper composites in marine environments is still limited. This study investigates the effects of mating materials, graphite content (30 wt.% and 45 wt.%), and electric voltage on the friction and wear mechanisms of graphite/copper composites in seawater. The results show that under seawater coupled with electricity, no mass loss was observed in the 30 wt.% graphite composites after friction tests against different counterparts. Electric voltage (3 V) affects the composite’s damage mechanism, inducing delamination wear, arc erosion and accelerating corrosion. Specifically, the electricity factor promotes oxidation recreations while inhibiting chlorine formation. Notably, when the composite is paired with gold-coated copper, it undergoes electrochemical reactions, leading to the formation of needle-like copper oxide. These oxides alter the surface morphology, elevate the mass of worn composites, and raise the friction coefficient of the tribopair to approximately 0.3, an increase from 0.2.
- Open Access
- 27 March 2024
- Published by MDPI AG in Electronics
- Vol. 13 (7) , 1235
Analysis of Kinematics and Dynamics of Rolling Ring Based on Finite Element Method
The working performance of the conductive rolling ring has a crucial impact on the overall energy security and on-orbit life of a satellite. To ensure the real-time transmission of signal and current, it is necessary to control the motion pattern of the rolling ring. In this paper, the finite element analysis method is used to carry out kinematics and dynamics simulation analysis, analyze the motion stability of the rolling ring, and discuss the relationship between the size of the idler gear, the driving torque, and the flexible contact pressure. The research results show that the numerical simulation and theoretical analysis show that the deviation angle is between 0 and 1.52 when the initial installation of the rolling ring is deviated by using the existing camber design of the inner and outer rings. Both have a self-recovery function. The driving torque and the size of the idler gear are nonlinear, and the contact force is proportional to the radius of the idler gear. With the increase in the compression of the radius of the flexible ring, the driving torque and the contact force will increase accordingly. The method of reducing the compression or increasing the size of the idler gear can be used to reduce the driving torque and maintain a certain contact to facilitate the transmission of electrical signals.
- 27 March 2024
- Published by MDPI AG in Electronics
- Vol. 13 (7) , 1235
Open AccessAnalysis of Kinematics and Dynamics of Rolling Ring Based on Finite Element Method
The working performance of the conductive rolling ring has a crucial impact on the overall energy security and on-orbit life of a satellite. To ensure the real-time transmission of signal and current, it is necessary to control the motion pattern of the rolling ring. In this paper, the finite element analysis method is used to carry out kinematics and dynamics simulation analysis, analyze the motion stability of the rolling ring, and discuss the relationship between the size of the idler gear, the driving torque, and the flexible contact pressure. The research results show that the numerical simulation and theoretical analysis show that the deviation angle is between 0 and 1.52 when the initial installation of the rolling ring is deviated by using the existing camber design of the inner and outer rings. Both have a self-recovery function. The driving torque and the size of the idler gear are nonlinear, and the contact force is proportional to the radius of the idler gear. With the increase in the compression of the radius of the flexible ring, the driving torque and the contact force will increase accordingly. The method of reducing the compression or increasing the size of the idler gear can be used to reduce the driving torque and maintain a certain contact to facilitate the transmission of electrical signals.