NWNenghui Wang

Nenghui Wang

*This is an algorithmically generated author record based on publicly available information.

Nenghui Wang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Enhanced Fatigue Endurance and Electrical Contact Stability of Flexible Rings via Optimized Cu/Ni/Au–Co Multilayer Electroplating

    by Xiaobin He, Yunfei Zhai, Jinbao Chen, Jingxuan Ma, Haihong Wu, Meng Zang, Chenfei Song

    Rolling electrical transmission devices for aerospace applications require high power capacity, long service life, and high reliability. As a critical rolling-contact component, the flexible ring undergoes repeated mechanical deformation and electrical loading, making its surface condition essential to fatigue endurance and contact stability. This study developed an optimized Cu/Ni/Au-Co multilayer electroplating strategy to mitigate surface degradation and unstable electrical contact. The coating comprised an optimized copper layer, a low-stress nickel sulfamate layer, and a gold–cobalt layer deposited from an electrolyte containing 0.6 g/L Co2+. The multilayer coating improved the surface and mechanical properties of flexible rings while maintaining stable electrical performance. Under current-carrying tension–compression loading, coated rings withstood over 100 million cycles, compared with approximately 30 million cycles for uncoated rings. Dynamic resistance tests using a rolling-joint verification device further confirmed stable electrical contact and good loop-to-loop consistency. These results demonstrate that the optimized multilayer coating effectively enhances fatigue endurance and dynamic contact stability, providing a practical surface-engineering solution for high-reliability aerospace rolling electrical transmission devices.

  • Open Access

    Composite Oxidation Mechanism of Cu/Cu Contact Pairs During Current-Carrying Rolling in O2-N2-H2O Vapor Mixture

    by Jianhua Cheng, Fei Li, Yuhang Li, Haihong Wu, Bohan Li, Chenfei Song, Zhibin Fu, Yongzhen Zhang

    Oxidation is a critical factor contributing to material wear and the degradation of conductive performance during current-carrying tribological processes. The present study investigated the composite oxidation mechanisms that occurred during current-carrying rolling in mixed atmospheres containing O2 and H2O vapor. The results obtained in a dry N2/O2 mixture, humid N2, and humid N2/O2 mixture indicated that the oxidation mechanisms on current-carrying rolling surfaces involved thermal oxidation, tribo-oxidation, and anodic oxidation. XPS analysis confirmed that the primary oxidation product was CuO. Conductive atomic force microscopy (C-AFM) revealed that surface oxidation caused a significant reduction in conductive α-spots, leading to an increase in contact resistance. Contact resistance exhibited a quasi-linear relationship with the surface CuO content. Contact angle measurements and adhesion tests showed that the enhanced hydrophilicity of the oxidized surface and the resulting high adhesion contributed to an increase in the macroscopic friction coefficient. In humid N2/O2 with 50% relative humidity (RH), the friction coefficient rapidly exceeded 0.8 when the O2 content surpassed 25%. Wear morphology analysis demonstrated that this abrupt increase in the friction coefficient induced fatigue wear on the surface. Overall, the present study elucidated the composite oxidation mechanisms during current-carrying rolling and clarified the pathways through which oxidation affected current-carrying tribological performance. These findings may contribute to improved failure analysis and the safe, reliable operation of electrical contact pairs.


  • Open Access

    Contact Load on the Current-Carrying Tribological Performance of Copper–Graphite Composites

    by Jiayu Ye, Nenghui Wang, Haihong Wu, Chuanfeng Wang, Xiao Kang

    This study investigates the current-carrying tribological properties and wear mechanisms of copper–graphite composites under varying contact loads. Two copper–graphite composites with different graphite content were prepared using the pressure sintering method. Current-carrying tribological tests were conducted at three distinct contact loads. Scanning electron microscopy, X-ray diffraction, laser confocal microscopy, and pin-on-disk tribological testing were utilized to examine the current-carrying tribological properties and the worn morphologies of the materials. The results indicate that, under the three contact loads, the friction coefficient of the copper–graphite materials ranged from 0.3 to 0.5, the wear rate was on the order of 10−13 m3/(N·m), the average voltage drop varied between 0.7 and 1.6 V, and the average electrical noise ranged from 0.2 to 0.9 mV. The wear mechanism included delamination wear and a minor amount of abrasive wear, and the lubricating film formed on the surface was mainly composed of C, PbO, and CuO. Notably, copper–graphite composites with lower graphite content exhibited superior hardness, electrical conductivity, and relative density compared to those with higher graphite content. At a contact load of 0.31 N, the copper–graphite composite containing 30wt% graphite demonstrated the most favorable current-carrying tribological performance, characterized by the lowest wear rate (1.09 × 10−13 m3/(N·m)), voltage drop (0.943 V), and electrical noise (0.234 mV).


  • Open Access

    Friction and Wear Performances and Mechanisms of Graphite/Copper Composites Under Electrical Contact in Marine Environments

    by Nenghui Wang, Chuanfeng Wang, Wenhu Xu, Weiping Cheng, Haihong Wu, Hongsheng Li

    Marine environment-induced apparatus failures have led to substantial losses in marine engineering. Graphite/copper composites, known for their excellent electrical conductivity and wear resistance, are extensively utilized in various electric contact devices. However, research on the current-carrying friction and wear behavior of graphite/copper composites in marine environments is still limited. This study investigates the effects of mating materials, graphite content (30 wt.% and 45 wt.%), and electric voltage on the friction and wear mechanisms of graphite/copper composites in seawater. The results show that under seawater coupled with electricity, no mass loss was observed in the 30 wt.% graphite composites after friction tests against different counterparts. Electric voltage (3 V) affects the composite’s damage mechanism, inducing delamination wear, arc erosion and accelerating corrosion. Specifically, the electricity factor promotes oxidation recreations while inhibiting chlorine formation. Notably, when the composite is paired with gold-coated copper, it undergoes electrochemical reactions, leading to the formation of needle-like copper oxide. These oxides alter the surface morphology, elevate the mass of worn composites, and raise the friction coefficient of the tribopair to approximately 0.3, an increase from 0.2.


  • Open Access

    Study on the Influences of Idler Materials on Rolling Electrical Contact Performance

    by Haihong Wu, Zhiyuan Qian, Chuankun Qu, Lei Zhang, Huiqun Liu, Xiao Kang

    The parallel connection of multiple flexible rings in raceways can significantly improve the electrical conductivity of rolling conductive devices. Multiple flexible rings are generally separated by idlers to form ring-idler rolling pairs. In the present work, alumina (Al2O3), polytetrafluoroethylene (PTFE), polyether ether ketone (PEEK), and polyimide (PI) were used as idler materials. Rolling tests for four types of ring-idler contact pairs were carried out in the air at a rotating speed of 10 rpm and a current of 60 A. It was noticed that the voltage drop was the lowest when Al2O3 was incorporated as the idler material. The energy spectrum analysis indicated material transfer between the organic idlers and the flexible ring. Especially on the flexible ring surface, the transferred organic thin film covered the gold-plated layer of the flexible ring and affected the electrical contact of the flexible ring. The transfer of Al2O3 was not obvious, and the mass fraction of Au on the flexible ring surface after the rolling test was 93.1%. The above results could help in selecting the best idler material for high-power conductive rotary joints.