Shukry Hammed Aghdeab
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shukry Hammed Aghdeab has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Asaad Ali Abbas
Production Engineering and Metallurgy Department, University of Technology, Baghdad, IRAQ
2 shared publications Marwa E. Kadhim
Production Engineering and Metallurgy Department, University of Technology-Iraq, Baghdad, Iraq
2 shared publications- Raed R. Shwaish
Production Engineering and Metallurgy Department, University of Technology, Baghdad, IRAQ
2 shared publications - Asmaa Omar Basheer
Construction and Projects Department, University of Technology, Baghdad, Iraq
1 shared publication - Bilal Çolak
KARABUK UNIVERSITY, ESKİPAZAR VOCATIONAL SCHOOL
1 shared publication Ghaith A. Makhrib
Department of Production Engineering and Metallurgy, University of Technology, Baghdad, Iraq
1 shared publication
Latest Publications
- Open Access
- 4 June 2025
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 15 (3) , 23680-23685
The Effect of Voltage on Material Removal Rate in the ECM Process
The development of machining processes, such as Electrochemical Machining (ECM), has improved manufacturing complex shapes and complicated materials. This research investigates the enhancement of the ECM process to achieve the highest quality of materials. Specifically, Material Removal Rate (MRR) is utilized as a performance parameter to reduce machining time and increase productivity without influencing product quality. This is accomplished through machining a workpiece made of high-speed steel AISI M2, using a copper tool in a sodium chloride (NaCl) solution. Optimal voltage parameters are determined to address issues, such as surface defects, power consumption, and process instability. The primary goal of this research are to enhance surface quality and ensure precision machining. The experiment includes three parameters, each one at three levels: voltage (10 V, 20 V, and 30 V), electrolyte concentration (20 g/L, 40 g/L, and 60 g/L), and a gap width (0.1 mm, 0.2 mm, and 0.3 mm). The experimental work is carried out on Minitab, a statistical software with a general full factorial design. A mathematical model is developed to create a figure through which is determined how MRR performs with variation of the three experiment parameters. Analysis of variance is performed through the ANOVA test to study the influence of the input parameters. The results indicate that MRR is significantly affected by voltage, followed by electrolyte concentration, while the gap width demonstrated minimal effect. Increasing voltage and electrolyte concentration leads to an increase in MRR. Similarly, increasing the gap width initially leads to a decrease in MRR, which then reaches a plateau. The maximum and minimum MRR values are 0.0871 g/min and 0.0023 g/min, respectively, revealing that voltage is an effective parameter for ECM quality optimization.
- 4 June 2025
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 15 (3) , 23680-23685
Open AccessThe Effect of Voltage on Material Removal Rate in the ECM Process
The development of machining processes, such as Electrochemical Machining (ECM), has improved manufacturing complex shapes and complicated materials. This research investigates the enhancement of the ECM process to achieve the highest quality of materials. Specifically, Material Removal Rate (MRR) is utilized as a performance parameter to reduce machining time and increase productivity without influencing product quality. This is accomplished through machining a workpiece made of high-speed steel AISI M2, using a copper tool in a sodium chloride (NaCl) solution. Optimal voltage parameters are determined to address issues, such as surface defects, power consumption, and process instability. The primary goal of this research are to enhance surface quality and ensure precision machining. The experiment includes three parameters, each one at three levels: voltage (10 V, 20 V, and 30 V), electrolyte concentration (20 g/L, 40 g/L, and 60 g/L), and a gap width (0.1 mm, 0.2 mm, and 0.3 mm). The experimental work is carried out on Minitab, a statistical software with a general full factorial design. A mathematical model is developed to create a figure through which is determined how MRR performs with variation of the three experiment parameters. Analysis of variance is performed through the ANOVA test to study the influence of the input parameters. The results indicate that MRR is significantly affected by voltage, followed by electrolyte concentration, while the gap width demonstrated minimal effect. Increasing voltage and electrolyte concentration leads to an increase in MRR. Similarly, increasing the gap width initially leads to a decrease in MRR, which then reaches a plateau. The maximum and minimum MRR values are 0.0871 g/min and 0.0023 g/min, respectively, revealing that voltage is an effective parameter for ECM quality optimization.
- Open Access
- 9 November 2024
- Published by Walter de Gruyter GmbH in Management Systems in Production Engineering
- Vol. 32 (4) , 563-570
Investigation of Electrochemical Discharge Machining for Tungsten Carbide: Effects of Electrolyte Composition on Material Removal Rate and Surface Quality
Tungsten carbide (WC-Co) with a cobalt binder has been widely used in industrial application. Through their high wear resistance and hardness, which make it a challenge to machine. Electrochemical discharge machining (ECDM) is a newly developed hybrid technique used to machine conductive and nonconductive materials. Tungsten carbide machining is an area that needs more investigation. In this study, different types of electrolytes have been tested in the electrochemical machining of tungsten carbide. It has been concluded that tungsten carbide was successfully machined with electrolytes that were either neutral salts or a combination of neutral salts and hydroxides, the highest material removal rate achieved was (0.09250 g/min), and the average surface roughness achieved in this work was measured at (Ra 0.9275 µm). However, deposition took place on the surface of machined tungsten carbide when the samples were treated with sodium hydroxide and potassium hydroxide. EDX analysis of successfully machined tungsten carbide samples reveal the presence of carbon (C) due to diffusion from the base material and oxygen (O), most likely due to oxidation brought on by the high temperatures utilized. Scanning electron microscopy confirmed that the machined surfaces had craters, pores, restricted microcracks, and re-deposited melt particles, among other things.
- 9 November 2024
- Published by Walter de Gruyter GmbH in Management Systems in Production Engineering
- Vol. 32 (4) , 563-570
Open AccessInvestigation of Electrochemical Discharge Machining for Tungsten Carbide: Effects of Electrolyte Composition on Material Removal Rate and Surface Quality
Tungsten carbide (WC-Co) with a cobalt binder has been widely used in industrial application. Through their high wear resistance and hardness, which make it a challenge to machine. Electrochemical discharge machining (ECDM) is a newly developed hybrid technique used to machine conductive and nonconductive materials. Tungsten carbide machining is an area that needs more investigation. In this study, different types of electrolytes have been tested in the electrochemical machining of tungsten carbide. It has been concluded that tungsten carbide was successfully machined with electrolytes that were either neutral salts or a combination of neutral salts and hydroxides, the highest material removal rate achieved was (0.09250 g/min), and the average surface roughness achieved in this work was measured at (Ra 0.9275 µm). However, deposition took place on the surface of machined tungsten carbide when the samples were treated with sodium hydroxide and potassium hydroxide. EDX analysis of successfully machined tungsten carbide samples reveal the presence of carbon (C) due to diffusion from the base material and oxygen (O), most likely due to oxidation brought on by the high temperatures utilized. Scanning electron microscopy confirmed that the machined surfaces had craters, pores, restricted microcracks, and re-deposited melt particles, among other things.
- Open Access
- 15 July 2024
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 43, 124-131
Energy efficiency and sustainability enhancement of electric discharge machines by incorporating nano-graphite
The research paper endeavored to significantly improve the energy efficiency and sustainability of the electrode wear rate (EWR) in electric discharge machining (EDM) through a particular exploration of various parameters. These parameters included nano-powder concentration, electric current, and pulse-on time. By systematically analyzing and manipulating these variables, the study aimed to optimize the EDM process, thereby reducing energy consumption and enhancing the overall sustainability of the machining operation. We employed the Powder Mixed Electro-Discharge Machining (PMEDM) technique, a refined iteration of electric discharge machining. This innovative method blended graphite nano-powder with transformer oil to serve as the dielectric medium. The primary objective of this investigation is to examine the outcomes concerning crucial process parameters such as graphite powder concentration, electric current, and pulse-on time when machining high-speed steel, focusing mainly on electrode wear rate (EWR). Incorporating nano graphite (Gr) mixed powders into dielectric liquids has demonstrated a discernible enhancement in EWR across diverse operational conditions. The study found that the electrode wear rate (EWR) varied based on nano-powder concentration, electric current, and pulse-on time. Maximum EWR was observed at a concentration of 10 g/L, a current of 30 A, and a pulse-on time of 70 µs, while minimum EWR occurred at 0 g/L, 10 A, and 60 µs. The Full Factorial design, executed with MINITAB 17 software, validated these findings. The optimal EWR recorded was 1.154 mm3/min. The coefficient of determination (R-sq) for surface roughness prediction also stood at 91.15%.
- 15 July 2024
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 43, 124-131
Open AccessEnergy efficiency and sustainability enhancement of electric discharge machines by incorporating nano-graphite
The research paper endeavored to significantly improve the energy efficiency and sustainability of the electrode wear rate (EWR) in electric discharge machining (EDM) through a particular exploration of various parameters. These parameters included nano-powder concentration, electric current, and pulse-on time. By systematically analyzing and manipulating these variables, the study aimed to optimize the EDM process, thereby reducing energy consumption and enhancing the overall sustainability of the machining operation. We employed the Powder Mixed Electro-Discharge Machining (PMEDM) technique, a refined iteration of electric discharge machining. This innovative method blended graphite nano-powder with transformer oil to serve as the dielectric medium. The primary objective of this investigation is to examine the outcomes concerning crucial process parameters such as graphite powder concentration, electric current, and pulse-on time when machining high-speed steel, focusing mainly on electrode wear rate (EWR). Incorporating nano graphite (Gr) mixed powders into dielectric liquids has demonstrated a discernible enhancement in EWR across diverse operational conditions. The study found that the electrode wear rate (EWR) varied based on nano-powder concentration, electric current, and pulse-on time. Maximum EWR was observed at a concentration of 10 g/L, a current of 30 A, and a pulse-on time of 70 µs, while minimum EWR occurred at 0 g/L, 10 A, and 60 µs. The Full Factorial design, executed with MINITAB 17 software, validated these findings. The optimal EWR recorded was 1.154 mm3/min. The coefficient of determination (R-sq) for surface roughness prediction also stood at 91.15%.
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3002 (1) , 060018
Study of electrode speed on material removal rate in electrochemical machining (ECM) process
Electrochemical machining (ECM) is a nontraditional machining technology that is used to operate the most challenging materials that are tough to work with in t Electrochemical machining (ECM) is a nontraditional machining technology that is used to operate the most challenging materials that are tough to work with in t
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3002 (1) , 060018
Study of electrode speed on material removal rate in electrochemical machining (ECM) process
Electrochemical machining (ECM) is a nontraditional machining technology that is used to operate the most challenging materials that are tough to work with in t Electrochemical machining (ECM) is a nontraditional machining technology that is used to operate the most challenging materials that are tough to work with in t
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3002 (1) , 080024
The effect of input parameters on material removal rate of CK45 DIN 17200 by electric discharge machining
The purpose of this research is to investigate the influence of input parameters (current, pulse on, pulse off) on materials eviction rate (MRR) when cutting CK The purpose of this research is to investigate the influence of input parameters (current, pulse on, pulse off) on materials eviction rate (MRR) when cutting CK
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3002 (1) , 080024
The effect of input parameters on material removal rate of CK45 DIN 17200 by electric discharge machining
The purpose of this research is to investigate the influence of input parameters (current, pulse on, pulse off) on materials eviction rate (MRR) when cutting CK The purpose of this research is to investigate the influence of input parameters (current, pulse on, pulse off) on materials eviction rate (MRR) when cutting CK
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2885 (1)
Effect of adding nano graphite powder on the material removal rate and surface roughness of electric spark machining
Electrical Discharge Machining (EDM) is widely utilized to fabricate different conductive materials counting those that are difficult to be machined with i Electrical Discharge Machining (EDM) is widely utilized to fabricate different conductive materials counting those that are difficult to be machined with i
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2885 (1)
Effect of adding nano graphite powder on the material removal rate and surface roughness of electric spark machining
Electrical Discharge Machining (EDM) is widely utilized to fabricate different conductive materials counting those that are difficult to be machined with i Electrical Discharge Machining (EDM) is widely utilized to fabricate different conductive materials counting those that are difficult to be machined with i
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2885 (1) , 020023
Study of electrode speed on surface roughness in electrochemical machining (ECM)process
Electrochemical machining (ECM) is one of nonconventional machining process used to operation the most harsh materials that difficult to operate in convent Electrochemical machining (ECM) is one of nonconventional machining process used to operation the most harsh materials that difficult to operate in convent
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2885 (1) , 020023
Study of electrode speed on surface roughness in electrochemical machining (ECM)process
Electrochemical machining (ECM) is one of nonconventional machining process used to operation the most harsh materials that difficult to operate in convent Electrochemical machining (ECM) is one of nonconventional machining process used to operation the most harsh materials that difficult to operate in convent
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2885 (1) , 070003
Study impact of gap distance on electrode wear rate in electrical discharge machining (EDM)
A wide range of crucial applications, including dies and the automobile industry, use the non-traditional cutting process known as EDM. In order to process A wide range of crucial applications, including dies and the automobile industry, use the non-traditional cutting process known as EDM. In order to process
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2885 (1) , 070003
Study impact of gap distance on electrode wear rate in electrical discharge machining (EDM)
A wide range of crucial applications, including dies and the automobile industry, use the non-traditional cutting process known as EDM. In order to process A wide range of crucial applications, including dies and the automobile industry, use the non-traditional cutting process known as EDM. In order to process