Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Raed R. Shwaish has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Effect of Severe Plastic Deformation on Mechanical Properties for A6061 Aluminum Alloy Fabricated by Multitypes of Bending Forming

    by Raed R. Shwaish, Mazin Al-Wswasi, Hind H. Abdulridha, Aseel Hamad Abed, Waleed Ahmed

    Severe plastic deformation (SPD) is a well‐known processing technique used to impose large plastic strains and modify the mechanical properties of metal‐based materials. In this work, SPD was introduced into A6061 aluminum alloy sheets via two forming processes: differential diameter rolling (DDR) and V‐bending. This hybrid DDR V‐bending approach addresses the limited understanding of how shear‐dominated prestraining produced by asymmetric rolling affects the subsequent bending response, spring‐back behavior, and energy absorption of A6061 aluminum alloy sheets, which are not fully captured by conventional symmetric rolling. The DDR process was performed at a rolling speed ratio of 1.15 using four sample reorientation conditions between successive passes, denoted as ND‐, RD‐, TD‐, and UD‐based routes. The thickness reduction ratios were 20%, 30%, and 40%, performed through three passes of the DDR process. Following the DDR process, the sheets were bent via a 90° V‐die to assess the following mechanical properties: hardness, maximum bending load, bending deflection, bending energy absorption, and spring‐back. Results of the experiments indicated that the thickness reduction ratio had a positive influence on strain hardening, leading to an increase in both hardness and spring‐back. However, the maximum bending load decreased with an increase in thickness reduction ratio, which occurs due to the reduction in the sheet thickness following the DDR process. Furthermore, the spring‐back angle and spring‐back factors were found to be higher for samples processed via the ND and RD rolling routes. The sheets rolled along the ND route produced the highest improvement in mechanical properties. Bending energy absorption increased with an increase in the thickness reduction ratio. The results of this study demonstrate that the DDR‐V‐bending process is effective in the modification of mechanical properties of A6061 aluminum alloy sheets. However, the reduction in bending load indicates a potential negative impact of the DDR process on the formability of the sheets.

  • Experimental Investigation of Energy Absorption in 3D-Printed Polymeric Axial Members under High and Low-Speed Impact

    by Raed R. Swaish, Maryam A. Sadiq, Adil Sh. Jaber, Waleed Ahmed

    The structural response of materials under dynamic impact loads is crucial in protective design, particularly in applications where energy absorption is a primary concern. This study presents a comprehensive experimental investigation into the energy storage potential of additively manufactured polymeric axial members subjected to high-speed and low-speed impact tests. These axial members were fabricated using additive manufacturing techniques, emphasizing optimizing their structural performance under deformation. The study focuses on assessing the performance of various internal infill geometries to enhance energy dissipation during impact loading. A series of tests was conducted to evaluate the members' capacity to absorb impact energy and to compare their performance under varied strain rates. The findings indicate that specific infill patterns significantly improve energy absorption capabilities, making them suitable for applications involving blast and impact-resistant designs. Furthermore, the results demonstrate that careful optimization of the internal structure of 3D-printed elements can effectively reduce the adverse effects of dynamic loads, making them a promising option for protective structures. The findings contribute to a broader understanding of material behavior at high strain rates, provide valuable guidance for designing lightweight, impact-resistant components, and provide new perspectives on utilizing innovative materials and manufacturing techniques to enhance structural resilience in demanding environments.

  • Open Access

    Impact of Uniaxial Pre-Strains on the Forming Limit Curve (FLC) of CuZn 70-30 Brass Sheets for Enhanced Formability in Production Applications Using the Nakajima Test

    by Aseel Hamad Abed, Raed R. Shwaish, Asaad Ali Abbas, Baha S. Mahdi, Waleed Ahmed

    Brass sheets are extensively utilized in the automotive, electrical, and other industries, where an in-depth understanding of their formability is crucial for achieving optimal performance in production applications. This study investigates the influence of uniaxial pre-strains on the Forming Limit Curve (FLC) of CuZn 70-30 brass sheets, which aims to enhance their formability by identifying and optimizing key forming parameters. Adding a new variable, the impact of uniaxial pre-strain upon FLC, was our aim of this study and, consequently, the CuZn 70-30 brass sheet formability using punch-stretching tests with purpose-built tools, we experimentally obtained FLCs for brass sheets under varying levels of pre-strain (0.04, 0.06, and 0.08) applied through uniaxial tension by using Nakajima tests with purpose-built tools. The objective was to understand how specific factors such as punch parameters, punch corner radius, and strain rate impact the FLC and, consequently, the brass sheets formability. Results indicate a distinct trend of increasing pre-strain levels leading to a significant rise in minor strain capacity along the right portionof the FLC, with a comparatively insignificant effect on the left. This consistent elevation across strain paths suggests improved formability due to pre-straining, highlighting the potential for optimized manufacturing processes and enhanced product quality across industrial applications.


  • Open Access

    Energy efficiency and sustainability enhancement of electric discharge machines by incorporating nano-graphite

    by Asaad A. Abbas, Raed R. Shwaish, Shukry H. Aghdeab, Waleed Ahmed

    The research paper endeavored to significantly improve the energy efficiency and sustainability of the electrode wear rate (EWR) in electric discharge machining (EDM) through a particular exploration of various parameters. These parameters included nano-powder concentration, electric current, and pulse-on time. By systematically analyzing and manipulating these variables, the study aimed to optimize the EDM process, thereby reducing energy consumption and enhancing the overall sustainability of the machining operation. We employed the Powder Mixed Electro-Discharge Machining (PMEDM) technique, a refined iteration of electric discharge machining. This innovative method blended graphite nano-powder with transformer oil to serve as the dielectric medium. The primary objective of this investigation is to examine the outcomes concerning crucial process parameters such as graphite powder concentration, electric current, and pulse-on time when machining high-speed steel, focusing mainly on electrode wear rate (EWR). Incorporating nano graphite (Gr) mixed powders into dielectric liquids has demonstrated a discernible enhancement in EWR across diverse operational conditions. The study found that the electrode wear rate (EWR) varied based on nano-powder concentration, electric current, and pulse-on time. Maximum EWR was observed at a concentration of 10 g/L, a current of 30 A, and a pulse-on time of 70 µs, while minimum EWR occurred at 0 g/L, 10 A, and 60 µs. The Full Factorial design, executed with MINITAB 17 software, validated these findings. The optimal EWR recorded was 1.154 mm3/min. The coefficient of determination (R-sq) for surface roughness prediction also stood at 91.15%.


  • Open Access

    Effect of the hollow electrode on the material removal rate of titanium alloy (grade 1) in the electrochemical machining (ECM) process

    by Montadher M. Maktuf, Raed R. Shwaish, Shukry H. Aghdeab

    This study examined the material removal rate (MRR) affected by the variables of the electrochemical process including electrode type, voltage, electrolyte type, electrolyte concentration, and gap. Titanium alloy was employed as the workpiece, while copper was utilized as the cylindrical electrode. The input parameters were established according to Taguchi’s methodology. An analysis of variance (ANOVA) using a linear regression model was dependent on making sense of the experiment’s findings. the solid electrode achieved the maximum material removal rate (MRR) value (0.0857) g/min, while the hollow electrode with (1500 l/hour) flow rate achieved the minimum material removal rate (MRR) value (0.00002) g/min. the material removal rate (MRR) was directly proportional to the voltage. Maximum material removal rate (MRR) occurred at a concentration of (75 g/l) for the (NH4C) electrolyte, while minimum material removal rate (MRR) occurred at a concentration of (50 g/l) for the (NH4Cl) electrolyte. It has been observed that the contributing factors in controlling material removal rate (MRR) were as follows; (66.67%) for the voltage, (5.89%) for the electrode, (5.72%) for the electrolyte concentration, (3.24%) for the type of electrolyte, and (3.07%) for the gap.


  • The effect of coated electrodes on electrode wear rate of titanium alloy (grade 1) by electric discharge machining

    by Maryam A. Sadik, Shukry H. Aghdeab, Raed R. Shwaish

    In the industry, electric spark cutting is a key cutting operation because it can efficiently cut both hard and difficult-to-work-with materials using tradition In the industry, electric spark cutting is a key cutting operation because it can efficiently cut both hard and difficult-to-work-with materials using tradition

  • Effect of adding nano graphite powder on the material removal rate and surface roughness of electric spark machining

    by Raed R. Shwaish, Shukry H. Aghdeab, Asaad A. Abbas

    Electrical Discharge Machining (EDM) is widely utilized to fabricate different conductive materials counting those that are difficult to be machined with i Electrical Discharge Machining (EDM) is widely utilized to fabricate different conductive materials counting those that are difficult to be machined with i

  • The Effect of Coated Electrodes on MRR of Titanium Metal by Spark Machining

    by Maryam A. Sadik, Shukry H. Aghdeab, Raed R. Shwaish

    The electric spark cutting process is one of the most important cutting processes in the world of industry because it allows for the cutting of metals with a high hardness and the formation of complex shapes. The purpose of this research is to investigate the influence of four copper electrodes on the material removal rate (MRR) when cutting titanium metal. Three copper electrodes were coated with various materials (nickel, silver, and gold). The inputs for the practical side were current in values (12, 24, and 42 A) and pulse on time in values (200, 400, and 600 µs). Optimal outcomes were achieved by the use of the analysis method (full factorial design). According to the practical results the MRR increases as the current and pulse on time increase. The electrode coated with gold had the highest MRR (139.6507mm 3 /min), while the electrode coated with nickel had the lowest MRR (5.8652 mm 3 /min). Furthermore, the predicted results are very closely to the practical results

  • Open Access

    Determination and Analysis of Residual Stress for AISI L2 Tool Steel in Electric Discharge Machine (EDM)

    by Shukry H Aghdeab, Raed R Shwaish, Tahseen M Salman

    Electric discharge machine is one of the most important non-traditional cutting processes conducted without contact between the workpiece and tool electrode. Each cutting process was associated with residual stresses, and these stresses are significant in determining life and product performance. This study aimed to determine the residual stress produced in the electric discharge machine (EDM) using the X-ray diffraction method. The used EDM parameters in this study are current Ip (10, 20, 30) A, pulse on-time Ton (50, 100, 150) μs, and pulse off-time Toff (6.5, 12,25) μs these parametric divided into 27 specimens. Full factorial was used to analyze the result using Minilab 17 software. The result showed that approximately between the experimentally and predict result. Also, the result illustrated that the residual stress was increasing with increases in each parametric EDM used. Maximum tensile residual stress is (838.86 Mpa) at a higher value of machine parameters, while the best residual stress achieved is compressive residual stress at low machine parameters, and it reaches 201 Mpa.


  • Open Access

    Effect of input parameters on MRR and EWR for tool steel AISI L2 by electric discharge machine (EDM)

    by Shukry H. Aghdeab, Raed R. Shwaish, Tahseen M. Salman

    Electric discharge machine (EDM) or may be call electric spark machine is one of most important of cutting process or manufacturing process because it give high accurate dimension and can be product most complex shape. In this present material removal rate (MRR) and electrode wear rate (EWR) for tool steel AISI L2 was study. The input parametric for this process is current, pulse on time and pulse off time. Full factorial method is used to formulate machine parameters and find the optimal process parameters of electric spark. The result show that the MRR is increasing with increasing in current and pulse on time while EWR is decreasing when current and pulse on time is increase. The experimented and predicted values of this process are approximately equal.