Daniel Useriu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Daniel Useriu has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Cristian Nechifor
Romanian Research and Development Institute for Gas Turbines COMOTI, Bucharest, Romania
2 shared publications - Iulian Vlăducă
The Romanian Research and Development Institute for Gas Turbines COMOTI, 061126 Bucharest, Romania
2 shared publications Adrian Savescu
INCDT COMOTI, Bucharest, Romania
1 shared publication- Adrian Săvescu1 shared publication
- Andrei Mitru
INCD Turbomotoare COMOTI, Bv. Iuliu Maniu 220D, Bucharest, Romania
1 shared publication - Claudia Borzea
Romanian Research and Development Institute for Gas Turbines COMOTI, 061126 Bucharest, Romania
1 shared publication
Latest Publications
- 1 April 2025
- Published by Comitetul National Roman al Consiliului Mondial al Energiei in EMERG - Energy. Environment. Efficiency. Resources. Globalization
- Vol. 11 (1) , 114-128
AUTOMATION AND ELECTRICAL CONTROL OF A COMPRESSED AIR ENERGY STORAGE SYSTEM
This work aims to develop the automation system for the motor-compressor and expander-generator systems of a compressed air energy installation, henceforth referred to as ROCAES. Considering that the expander and compressor operate independently according to the scope of work, a solution comprising two separate automation systems that work together was chosen. The software programming was performed relying on the established parameter lists and in accordance with the project’s piping and instrumentation diagram, as well as the equipment mounted on the skid and in the automation cabinets. Guidelines are provided for future development, emphasizing the strengths and weaknesses of the solution.
- 1 April 2025
- Published by Comitetul National Roman al Consiliului Mondial al Energiei in EMERG - Energy. Environment. Efficiency. Resources. Globalization
- Vol. 11 (1) , 114-128
AUTOMATION AND ELECTRICAL CONTROL OF A COMPRESSED AIR ENERGY STORAGE SYSTEM
This work aims to develop the automation system for the motor-compressor and expander-generator systems of a compressed air energy installation, henceforth referred to as ROCAES. Considering that the expander and compressor operate independently according to the scope of work, a solution comprising two separate automation systems that work together was chosen. The software programming was performed relying on the established parameter lists and in accordance with the project’s piping and instrumentation diagram, as well as the equipment mounted on the skid and in the automation cabinets. Guidelines are provided for future development, emphasizing the strengths and weaknesses of the solution.
- 27 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Automation Control System for Naval Propulsion Retrofitting
Nowadays, automation systems for naval propulsion groups with gas turbines use programmable logic controllers for a precise and reliable control. The automation system is designed so as to be able to connect using signal cables to the transducers monitoring the engine’s parameters, via adapters, so that the command and regulation functions to be fully automatized. These signals are managed by means of the software program implemented in the PLC, and subsequent data acquisition. One of the important problems is the available resource of the propulsion group, until capital repair is required. The remaining lifetime depends on the operating regimes of the gas turbine engine. This problem is more pronounced in the propulsion groups equipping navy ships, where the dynamic regimes of gas turbine engines are much more demanding, and hence the pre-established operating limits may be exceeded. The automation configuration presented herein ensures the accurate computation and precise control of essential parameters for which the direct measurement is not possible using transducers. These parameters are the exhaust gas temperature, the power developed by the engine and implicitly the torque developed at propeller shaft.
- 27 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Automation Control System for Naval Propulsion Retrofitting
Nowadays, automation systems for naval propulsion groups with gas turbines use programmable logic controllers for a precise and reliable control. The automation system is designed so as to be able to connect using signal cables to the transducers monitoring the engine’s parameters, via adapters, so that the command and regulation functions to be fully automatized. These signals are managed by means of the software program implemented in the PLC, and subsequent data acquisition. One of the important problems is the available resource of the propulsion group, until capital repair is required. The remaining lifetime depends on the operating regimes of the gas turbine engine. This problem is more pronounced in the propulsion groups equipping navy ships, where the dynamic regimes of gas turbine engines are much more demanding, and hence the pre-established operating limits may be exceeded. The automation configuration presented herein ensures the accurate computation and precise control of essential parameters for which the direct measurement is not possible using transducers. These parameters are the exhaust gas temperature, the power developed by the engine and implicitly the torque developed at propeller shaft.