Daniel Lale
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Daniel Lale has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Cristian Nechifor
Romanian Research and Development Institute for Gas Turbines COMOTI, Bucharest, Romania
3 shared publications - Adrian Stoicescu
Romanian Research and Development Institute for Gas Turbines COMOTI, Bucharest, Romania
2 shared publications Claudia Săvescu
Romanian Research and Development Institute for Gas Turbines COMOTI
2 shared publications- Daniel Comeagă
Faculty of Mechanical Engineering and Mechatronics, National University of Science and Technology POLITEHNICA Bucharest, 060042 Bucharest, Romania
2 shared publications - Mihaela Roman
Romanian Research and Development Institute for Gas Turbines COMOTI, Bucharest, Romania
2 shared publications - Andrei Mitru
INCD Turbomotoare COMOTI, Bv. Iuliu Maniu 220D, Bucharest, Romania
1 shared publication
Latest Publications
- Open Access
- 17 November 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (4) , 597-602
AUTOMATION SYSTEM OF AN EDUCATIONAL TEST BENCH FOR NAVAL PISTON DIESEL ENGINES
The paper focuses on the custom automation system of a test bench for diesel engines used on navy ships, namely on tugboats. The test bench, with its automation system, is developed for practical training at a naval academy. The test bench aims to meet the highest standards in the education of Navy students and personnel. It facilitates undertaking practical laboratory works regarding the main constructive elements, operation, monitoring, and maintenance of four-stroke internal combustion engines, of the gearbox, as well as of the propeller load simulated by a hydraulic brake. The custom-made automation control system includes a modular cabinet with drives and automation sections, featuring a local command console for engine control and a remote command console for the entire test bench, with a large display for parameter monitoring.
- 17 November 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (4) , 597-602
Open AccessAUTOMATION SYSTEM OF AN EDUCATIONAL TEST BENCH FOR NAVAL PISTON DIESEL ENGINES
The paper focuses on the custom automation system of a test bench for diesel engines used on navy ships, namely on tugboats. The test bench, with its automation system, is developed for practical training at a naval academy. The test bench aims to meet the highest standards in the education of Navy students and personnel. It facilitates undertaking practical laboratory works regarding the main constructive elements, operation, monitoring, and maintenance of four-stroke internal combustion engines, of the gearbox, as well as of the propeller load simulated by a hydraulic brake. The custom-made automation control system includes a modular cabinet with drives and automation sections, featuring a local command console for engine control and a remote command console for the entire test bench, with a large display for parameter monitoring.
- Open Access
Performance and Uncertainty Analysis of Digital vs. Analog Pressure Scanners Under Static and Dynamic Conditions
Dynamic pressure measurement is an important component in the turbo engine testing process. This paper presents a comparative analysis between two types of multichannel electronic pressure measurement systems, commonly known as pressure scanners, used for this purpose: ZOC17/8Px, with analog amplification per channel, and MPS4264, a modern digital system with integrated A/D conversion. The study was conducted in two stages: a metrological verification and validation in static mode, using a high-precision pressure standard, and an experimental stage in dynamic mode, where data was acquired from a turbojet engine test stand, in constant engine speed mode. The signal stability of the pressure scanners was statistically analyzed by determining the coefficient of variation in the signal and the frequency spectrum (FFT) for each channel of the pressure scanners. Furthermore, comprehensive uncertainty budgets were calculated for both systems. The results highlight the superior stability and reduced uncertainty of the MPS4264 pressure scanner, attributing its enhanced performance to digital integration and a higher resilience to external noise. The findings support the adoption of modern digital systems for dynamic applications and provide a robust metrological basis for the optimal selection of measurement systems.
Open AccessPerformance and Uncertainty Analysis of Digital vs. Analog Pressure Scanners Under Static and Dynamic Conditions
Dynamic pressure measurement is an important component in the turbo engine testing process. This paper presents a comparative analysis between two types of multichannel electronic pressure measurement systems, commonly known as pressure scanners, used for this purpose: ZOC17/8Px, with analog amplification per channel, and MPS4264, a modern digital system with integrated A/D conversion. The study was conducted in two stages: a metrological verification and validation in static mode, using a high-precision pressure standard, and an experimental stage in dynamic mode, where data was acquired from a turbojet engine test stand, in constant engine speed mode. The signal stability of the pressure scanners was statistically analyzed by determining the coefficient of variation in the signal and the frequency spectrum (FFT) for each channel of the pressure scanners. Furthermore, comprehensive uncertainty budgets were calculated for both systems. The results highlight the superior stability and reduced uncertainty of the MPS4264 pressure scanner, attributing its enhanced performance to digital integration and a higher resilience to external noise. The findings support the adoption of modern digital systems for dynamic applications and provide a robust metrological basis for the optimal selection of measurement systems.
- Open Access
- 25 March 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (1) , 9-14
EXPERIMENTAL STUDY OF A PIEZOELECTRIC HARVESTER VIBRATING ON AN INDUSTRIAL SCREW COMPRESSOR
The paper presents preliminary experimental works on a twin-screw compressor to validate and demonstrate piezoelectric energy harvesting. The experiments target an industrially relevant environment: a test bench for industrial air and gas compressors. This work was only possible after previous studies assessing the piezoelectric harvester’s behavior, considering essential factors. In our case, a high working temperature may negatively influence the piezoelectric response and can even damage the material; hence, it should be avoided as much as possible. The piezoelectric harvester’s resonant frequency ought to be adjusted in real-time to match as closely as possible the target vibration frequency of the male rotor, of ~83 Hz. We obtained a voltage peak response of ~4 VAC and a maximum measured RMS current of ~515 µA. The RMS power, calculated at about 1.5 mW, was deemed very satisfactory for a piezoelectric device.
- 25 March 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (1) , 9-14
Open AccessEXPERIMENTAL STUDY OF A PIEZOELECTRIC HARVESTER VIBRATING ON AN INDUSTRIAL SCREW COMPRESSOR
The paper presents preliminary experimental works on a twin-screw compressor to validate and demonstrate piezoelectric energy harvesting. The experiments target an industrially relevant environment: a test bench for industrial air and gas compressors. This work was only possible after previous studies assessing the piezoelectric harvester’s behavior, considering essential factors. In our case, a high working temperature may negatively influence the piezoelectric response and can even damage the material; hence, it should be avoided as much as possible. The piezoelectric harvester’s resonant frequency ought to be adjusted in real-time to match as closely as possible the target vibration frequency of the male rotor, of ~83 Hz. We obtained a voltage peak response of ~4 VAC and a maximum measured RMS current of ~515 µA. The RMS power, calculated at about 1.5 mW, was deemed very satisfactory for a piezoelectric device.
- Open Access
- 2 April 2024
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 14 (2) , 13449-13455
Thermal Potential of a Twin-Screw Compressor as Thermoelectric Energy Harvesting Source
This study evaluates the potential of a twin-screw compressor as a heat source to harness thermal energy. Thermoelectric generators are a feasible solution for microenergy harvesting from waste heat based on the Seebeck effect. Thermographic infrared images of the compressor were used to assess potential installation spots. The physical mounting of the thermoelectric modules must consider certain hindering aspects. At first, the compressor skid is subject to standards and authorizations for its components, leaving only a couple of spots for screw-mounted module installations. Another inconvenience is the bonds in any thermoelectric material causing them not to withstand lateral mechanical stress in other directions except the c-axis perpendicular to the layers. Therefore, vibration measurements have to be performed beforehand. Numerical simulations were conducted, relying on the acquired thermoelectric modules as well as on the temperature and vibration data measured on the compressor. The thermoelectric generators studied are part of a multisource piezoelectric and thermoelectric energy harvesting system under research and development.
- 2 April 2024
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 14 (2) , 13449-13455
Open AccessThermal Potential of a Twin-Screw Compressor as Thermoelectric Energy Harvesting Source
This study evaluates the potential of a twin-screw compressor as a heat source to harness thermal energy. Thermoelectric generators are a feasible solution for microenergy harvesting from waste heat based on the Seebeck effect. Thermographic infrared images of the compressor were used to assess potential installation spots. The physical mounting of the thermoelectric modules must consider certain hindering aspects. At first, the compressor skid is subject to standards and authorizations for its components, leaving only a couple of spots for screw-mounted module installations. Another inconvenience is the bonds in any thermoelectric material causing them not to withstand lateral mechanical stress in other directions except the c-axis perpendicular to the layers. Therefore, vibration measurements have to be performed beforehand. Numerical simulations were conducted, relying on the acquired thermoelectric modules as well as on the temperature and vibration data measured on the compressor. The thermoelectric generators studied are part of a multisource piezoelectric and thermoelectric energy harvesting system under research and development.
- Open Access
- 6 January 2022
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 354, 00044
Modular automation cabinet for proactive monitoring in ATEX Zone 2
The paper presents an automation system dedicated to oil & gas machinery applications, such as electrical gas compressors. The future aim is to introduce it into the Romanian oil & gas industry. The system consists of a low size cabinet and its dependencies, which can be used in ATEX Zone 2. The electronic equipment is dimensioned and chosen according to the standards in force, so that the limited current and voltage requirements for methane gas to be met. The key feature is that this system complies with all ATEX standards for Zone 2. Moreover, it can also be a mobile and modular solution if needed, for a versatile and easy use in proactive monitoring of multiple locations across various compressor plants. The design, wireless transmission and possible implementation of this cabinet are presented. Remote data transmission via Wi-Fi and RS-485 communication interfaces between the devices is considered, due to several advantages: mobility, versatility, wide compatibility, environmentally friendly, as well as higher resources efficiency (reducing time and costs).
- 6 January 2022
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 354, 00044
Open AccessModular automation cabinet for proactive monitoring in ATEX Zone 2
The paper presents an automation system dedicated to oil & gas machinery applications, such as electrical gas compressors. The future aim is to introduce it into the Romanian oil & gas industry. The system consists of a low size cabinet and its dependencies, which can be used in ATEX Zone 2. The electronic equipment is dimensioned and chosen according to the standards in force, so that the limited current and voltage requirements for methane gas to be met. The key feature is that this system complies with all ATEX standards for Zone 2. Moreover, it can also be a mobile and modular solution if needed, for a versatile and easy use in proactive monitoring of multiple locations across various compressor plants. The design, wireless transmission and possible implementation of this cabinet are presented. Remote data transmission via Wi-Fi and RS-485 communication interfaces between the devices is considered, due to several advantages: mobility, versatility, wide compatibility, environmentally friendly, as well as higher resources efficiency (reducing time and costs).