Lingxin Meng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lingxin Meng has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Menglian Zhao
Institute of VLSI Design, Zhejiang University, Hangzhou, China
6 shared publications - Zhichao Tan
College of Information and Electronics Engineering, Zhejiang University, Hangzhou, China
6 shared publications - Shuang Song
Zhejiang University
3 shared publications - Shan Zhang
Zhejiang University
2 shared publications - Wanyuan Qu
College of Integrated Circuits, Zhejiang University, Hangzhou, China
2 shared publications Junsheng Chen
College of Information Science and Electronic Engineering, Zhejiang University, Hangzhou, China
1 shared publication
Latest Publications
- 11 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (3) , 898-911
A High-Precision Level-Crossing Pipelined ADC With Trigger-Sampled Backend Stage
This article presents a high-precision level-crossing (LC) pipelined analog-to-digital converter (ADC) for sparse signal processing, addressing the critical resolution challenge in conventional LC architecture. A triggered sampling technique is proposed to eliminate the misalignment between the output timestamp and the output voltage amplitude in conventional continuous-time (CT) LC ADCs, which is achieved by sampling the input signal according to the triggering signal from a4-bit LC detector. Moreover, the signal-dependent error caused by the inevitable CT comparator delay is thus accurately extracted by feeding back the LC output codes. A $16{\times }$ redundancy-free residue amplifier (RA), followed by an 8-bit second-stage successive approximation register (SAR) ADC, is adopted to perform finer quantization and improve the resolution. Fabricated in a55-nm CMOS process, the prototype ADC achieves a measured peak SNDR of 72.5 dB with a 6.6-kHz input under a 1-V supply, achieving the highest reported SNDR and providing an 8-dB improvement over state-of-the-art. Also, thanks to the LC scheme, the proposed ADC demonstrates a dynamic power consumption from $1.2~{\mu }$ W (static) to $11.8~{\mu }$ W (20-kHz input), yielding Walden FoM (FoM w ) of 9–86 fJ/conv.step.
- 11 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (3) , 898-911
A High-Precision Level-Crossing Pipelined ADC With Trigger-Sampled Backend Stage
This article presents a high-precision level-crossing (LC) pipelined analog-to-digital converter (ADC) for sparse signal processing, addressing the critical resolution challenge in conventional LC architecture. A triggered sampling technique is proposed to eliminate the misalignment between the output timestamp and the output voltage amplitude in conventional continuous-time (CT) LC ADCs, which is achieved by sampling the input signal according to the triggering signal from a4-bit LC detector. Moreover, the signal-dependent error caused by the inevitable CT comparator delay is thus accurately extracted by feeding back the LC output codes. A $16{\times }$ redundancy-free residue amplifier (RA), followed by an 8-bit second-stage successive approximation register (SAR) ADC, is adopted to perform finer quantization and improve the resolution. Fabricated in a55-nm CMOS process, the prototype ADC achieves a measured peak SNDR of 72.5 dB with a 6.6-kHz input under a 1-V supply, achieving the highest reported SNDR and providing an 8-dB improvement over state-of-the-art. Also, thanks to the LC scheme, the proposed ADC demonstrates a dynamic power consumption from $1.2~{\mu }$ W (static) to $11.8~{\mu }$ W (20-kHz input), yielding Walden FoM (FoM w ) of 9–86 fJ/conv.step.
- Open Access
- 16 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Solid-State Circuits Society
- Vol. 5, 157-166
Analysis and Design of a Low-Voltage High-Precision Switched-Capacitor Delta–Sigma Modulator
Low-voltage delta-sigma modulators have broad application prospects in power-constrained sensor systems but with undeveloped energy efficiency. This article includes the current development of low-voltage DSMs and the design challenges of low-voltage DT DSMs. As a case study, a DT zoom DSM with a low-voltage capacitively-biased floating inverter amplifier is presented with detailed design considerations. Fabricated in 55 nm CMOS under a 0.5 V supply, the prototype achieves 83.6 dB SNDR and 86.0 dB dynamic range while only consuming 664 nW at a signal bandwidth of 1k Hz. This achieves a state-of-the-art SNDR-based FoM of 175.4 dB among low-voltage switched-capacitor DSMs.
- 16 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Solid-State Circuits Society
- Vol. 5, 157-166
Open AccessAnalysis and Design of a Low-Voltage High-Precision Switched-Capacitor Delta–Sigma Modulator
Low-voltage delta-sigma modulators have broad application prospects in power-constrained sensor systems but with undeveloped energy efficiency. This article includes the current development of low-voltage DSMs and the design challenges of low-voltage DT DSMs. As a case study, a DT zoom DSM with a low-voltage capacitively-biased floating inverter amplifier is presented with detailed design considerations. Fabricated in 55 nm CMOS under a 0.5 V supply, the prototype achieves 83.6 dB SNDR and 86.0 dB dynamic range while only consuming 664 nW at a signal bandwidth of 1k Hz. This achieves a state-of-the-art SNDR-based FoM of 175.4 dB among low-voltage switched-capacitor DSMs.
- 6 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (6) , 2084-2095
A 93.6-dB SNDR Fully Dynamic CT-DT Noise-Shaping SAR ADC With Closed-Loop Capacitively Coupled Two-Stage FIA
This article presents an embedded-friendly high-precision two-step noise-shaping (NS) successive approximation register (SAR) analog-to-digital converter (ADC) designed for sensor applications. By employing a continuous-time (CT) SAR to track the input signal, the design avoids the kT/C noise typically induced by sampling operations. This approach decouples the signal-to-noise ratio (SNR) from the size of the sampling capacitor, thus relaxing the burden of the input and reference buffers. The CT SAR is followed by a two-stage floating-inverter-amplifier (FIA)-based closed-loop residue amplifier (RA) with a 94.6-dB open-loop gain, effectively mitigating interstage gain error. Furthermore, the CT–DT NS SAR exhibits high energy efficiency and fully dynamic characteristics due to the proposed RA and the second-stage DT NS SAR. Fabricated in a 55-nm CMOS process, the prototype achieves a signal-to-noise and distortion ratio (SNDR) of 93.6 dB with only a 120-fF single-ended input capacitor at a signal bandwidth of 5 kHz. Operating at a 1-MHz operating rate, the prototype consumes 34.7 $\mu$ W from a 1.2-V supply, resulting in a Schreier figure of merit (FoM) of 175.2 dB.
- 6 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (6) , 2084-2095
A 93.6-dB SNDR Fully Dynamic CT-DT Noise-Shaping SAR ADC With Closed-Loop Capacitively Coupled Two-Stage FIA
This article presents an embedded-friendly high-precision two-step noise-shaping (NS) successive approximation register (SAR) analog-to-digital converter (ADC) designed for sensor applications. By employing a continuous-time (CT) SAR to track the input signal, the design avoids the kT/C noise typically induced by sampling operations. This approach decouples the signal-to-noise ratio (SNR) from the size of the sampling capacitor, thus relaxing the burden of the input and reference buffers. The CT SAR is followed by a two-stage floating-inverter-amplifier (FIA)-based closed-loop residue amplifier (RA) with a 94.6-dB open-loop gain, effectively mitigating interstage gain error. Furthermore, the CT–DT NS SAR exhibits high energy efficiency and fully dynamic characteristics due to the proposed RA and the second-stage DT NS SAR. Fabricated in a 55-nm CMOS process, the prototype achieves a signal-to-noise and distortion ratio (SNDR) of 93.6 dB with only a 120-fF single-ended input capacitor at a signal bandwidth of 5 kHz. Operating at a 1-MHz operating rate, the prototype consumes 34.7 $\mu$ W from a 1.2-V supply, resulting in a Schreier figure of merit (FoM) of 175.2 dB.
- 1 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (4) , 1510-1521
An 871 nW 96.2 dB SNDR Pipelined Second-Order Noise-Shaping SAR ADC Employing Charge-Efficient CLS-Assisted Residue Amplifier
This article presents a two-stage pipelined noise-shaping (NS) successive-approximation-register (SAR) analog-to-digital converters (ADCs) for sub-micro-watt and high-resolution applications. However, it asks for an accurate residue amplification to avoid severe quantization noise leakage from the frontend stage. Therefore, a charge-efficient correlated-level-shifting (CECLS) assisted residue amplifier (RA) is designed by inserting the level-shifting network (LSN) in a two-stage floating inverter amplifier (FIA). In addition to the inherited low-power merit from FIA, it boosts the equivalent open-loop gain to 92 dB while preventing bandwidth reduction and charge-sharing effects, making the amplification more accurate and faster than prior CLS-assisted amplifiers. The prototype is fabricated using 55 nm CMOS technology and occupies an active area of 0.26 mm $^{\mathbf{2}}$ . The measurement results show a 96.2 dB peak-SNDR and 871 nW power consumption under a 1.2 V supply voltage with a 16 kS/s sampling rate. Compared to the recent state-of-the-art ADCs with power under 10 $\mu$ W and SNDR exceeding 90 dB, this ADC presents the best Schreier FoM of 180.8 dB.
- 1 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (4) , 1510-1521
An 871 nW 96.2 dB SNDR Pipelined Second-Order Noise-Shaping SAR ADC Employing Charge-Efficient CLS-Assisted Residue Amplifier
This article presents a two-stage pipelined noise-shaping (NS) successive-approximation-register (SAR) analog-to-digital converters (ADCs) for sub-micro-watt and high-resolution applications. However, it asks for an accurate residue amplification to avoid severe quantization noise leakage from the frontend stage. Therefore, a charge-efficient correlated-level-shifting (CECLS) assisted residue amplifier (RA) is designed by inserting the level-shifting network (LSN) in a two-stage floating inverter amplifier (FIA). In addition to the inherited low-power merit from FIA, it boosts the equivalent open-loop gain to 92 dB while preventing bandwidth reduction and charge-sharing effects, making the amplification more accurate and faster than prior CLS-assisted amplifiers. The prototype is fabricated using 55 nm CMOS technology and occupies an active area of 0.26 mm $^{\mathbf{2}}$ . The measurement results show a 96.2 dB peak-SNDR and 871 nW power consumption under a 1.2 V supply voltage with a 16 kS/s sampling rate. Compared to the recent state-of-the-art ADCs with power under 10 $\mu$ W and SNDR exceeding 90 dB, this ADC presents the best Schreier FoM of 180.8 dB.
- 4 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (9) , 2735-2746
A Partially Feedback NSSAR Embedded Third-Order Delta–Sigma Modulator With Gain-Boosted Two-Stage FIAs
This article presents a switched-capacitor (SC) delta–sigma modulator (DSM) for low-power and high-precision applications. With a 5-bit noise-shaping (NS) successive-approximation-register (NSSAR) quantizer embedded in the 2nd-order loop filter, the system achieves a stable 3rd-order noise transfer function (NTF) without coefficient scaling. Partial feedback with digital filters is adopted, which only feeds back the 3 MSBs, leading to a fourfold reduction of data-weighted-averaging (DWA) complexity. To mitigate the noise leakage, a gain-boosted two-stage floating inverter amplifier (FIA) with 87.2-dB open-loop gain is proposed with the assistance of the Correlated-level-shifting (CLS) technique. The stability and noise performance of the FIA are also optimized. Fabricated in a 55-nm CMOS process, the prototype analog-to-digital converter (ADC) achieves a measured 93.7-dB signal to noise and distortion ratio (SNDR) in a 10-kHz bandwidth at 800 kS/s at a oversampling ratio (OSR) of 40. With 33.2- $\mu \text{W}$ power consumption, it achieves an SNDR-based Schreier figure of merit (FoM) of 178.5 dB and a Walden FoM of 41.9 fJ/conv, demonstrating state-of-the-art energy efficiency. Furthermore, the prototype exhibits fully dynamic characteristics and capabilities to a higher dynamic range (DR).
- 4 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (9) , 2735-2746
A Partially Feedback NSSAR Embedded Third-Order Delta–Sigma Modulator With Gain-Boosted Two-Stage FIAs
This article presents a switched-capacitor (SC) delta–sigma modulator (DSM) for low-power and high-precision applications. With a 5-bit noise-shaping (NS) successive-approximation-register (NSSAR) quantizer embedded in the 2nd-order loop filter, the system achieves a stable 3rd-order noise transfer function (NTF) without coefficient scaling. Partial feedback with digital filters is adopted, which only feeds back the 3 MSBs, leading to a fourfold reduction of data-weighted-averaging (DWA) complexity. To mitigate the noise leakage, a gain-boosted two-stage floating inverter amplifier (FIA) with 87.2-dB open-loop gain is proposed with the assistance of the Correlated-level-shifting (CLS) technique. The stability and noise performance of the FIA are also optimized. Fabricated in a 55-nm CMOS process, the prototype analog-to-digital converter (ADC) achieves a measured 93.7-dB signal to noise and distortion ratio (SNDR) in a 10-kHz bandwidth at 800 kS/s at a oversampling ratio (OSR) of 40. With 33.2- $\mu \text{W}$ power consumption, it achieves an SNDR-based Schreier figure of merit (FoM) of 178.5 dB and a Walden FoM of 41.9 fJ/conv, demonstrating state-of-the-art energy efficiency. Furthermore, the prototype exhibits fully dynamic characteristics and capabilities to a higher dynamic range (DR).