YWYanwei Wu

Yanwei Wu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yanwei Wu has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Evaluation of Bonding Behavior between Engineered Geopolymer Composites with Hybrid PE/PVA Fibers and Concrete Substrate

    by Yu Ling, Xiafei Zhang, Yanwei Wu, Weiyu Zou, Chuang Wang, Chaosen Li, Wen Li

    Engineered geopolymer composites (EGCs) exhibit excellent tensile ductility and crack control ability, making them promising for concrete structure repair. However, their widespread use is limited by high costs of reinforcement fiber and a lack of an EGC–concrete interface bonding mechanism. This study investigated a hybrid PE/PVA fiber-reinforced EGC using domestically produced unoiled PVA fibers to replace commonly used PE fibers. The bond performance of the EGC–concrete interface was evaluated through direct tensile and slant shear tests, focusing on the effects of PE fiber content (1%, 2%, and 3%), fiber hybrid ratios (2.0:0.0, 1.5:0.5, 1.0:1.0, 0.5:1.5, and 0.0:2.0), concrete substrate strength (C30, C50, and C70), and the ratio of fly ash (FA) to ground granulated blast furnace slag (GGBS) (6:4, 7:3, and 8:2) on interface bond strength. Results showed that the EGCs’ compressive strength ranged from 77.1 to 108.9 MPa, with increased GGBS content significantly enhancing the compressive strength and elastic modulus. Most of the specimens exhibited strain-hardening behavior after initial cracking. Interface bonding tests revealed that a PE/PVA ratio of 1.0 increased tensile bond strength by 8.5% compared with using 2.0% PE fiber alone. Increasing the PE fiber content, PVA/PE ratio, GGBS content, and concrete substrate strength all improved the shear bond strength. This improvement was attributed to the flexible fibers’ ability to restrict thermo–hydro damage and deflect and blunt microcracks, enhancing the interface’s failure resistance. Cost analysis showed that replacing 50% of the PE fiber in EGC with unoiled PVA fiber reduced costs by 44.2% compared with PE fiber alone, offering the best cost–performance ratio. In summary, hybrid PE/PVA fiber EGC has promising prospects for improving economic efficiency while maintaining tensile ductility and crack-control ability. Future optimization of fiber ratios and interface design could further enhance its potential for concrete repair applications.


  • Open Access

    Axial Impact Resistance of High-Strength Engineering Geopolymer Composites: Effect of Polyethylene Fiber Content and Strain Rate

    by Yu Ling, Xiafei Zhang, Weiyu Zou, Chang Feng, Huaming Lai, Jialin Yang, Beixin Xie

    High-strength engineered geopolymer composite (EGC) materials exhibit excellent mechanical properties under quasistatic loading, thus showing great potential in military and civilian facilities subjected to impact or explosive loading. However, its dynamic mechanical response under high-speed loading is not fully understood. In this study, dynamic compressive test was performed on EGC with PE fiber contents of 0%, 0.5%, 1.0%, 1.5%, and 2.0% using the Split Hopkinson Pressure Bar (SHPB) test. The results indicated that EGC reinforced with 1.5% fiber exhibited optimal static and dynamic mechanical performance. In the strain rate range of 181 s−1 to 201 s−1, when the fiber content increased from 1.0% to 1.5% and 2.0%, the dynamic compressive strength of the EGC increased by 24.3%, 28.8%, and 44.0%, respectively, compared to the matrix without fiber. Dynamic parameters of the EGC, including dynamic compressive strength, dynamic increase factor, and impact toughness, showed sensitivity to strain rates and increased with strain rate. A modified model, incorporating the fiber bridging effect, was proposed based on the CEB-FIP model, providing important guidance for practical engineering applications.


  • Open Access

    Comprehensive Analysis of Mechanical, Economic, and Environmental Characteristics of Hybrid PE/PP Fiber-Reinforced Engineered Geopolymer Composites

    by Xiafei Zhang, Yu Ling, Yanwei Wu, Huaming Lai, Yingchang Wang, Zhanbiao Chen

    Engineered Geopolymer Composites (EGCs), known for their excellent tensile properties and lower carbon emissions, have gained widespread attention in the field of fiber-reinforced concrete. However, the high cost of high-performance synthetic fibers, a crucial component of EGCs, limits their practical engineering applications. In this study, by using low-cost PP fibers hybridized with PE fibers and adjusting the fly ash/ground granulated blast furnace slag (FA/GGBS) ratio, cost-effective, high-performing hybrid PE/PP-reinforced engineered geopolymer composites (H-EGCs) were developed. This study conducted axial compressive and tensile tests on H-EGCs with different FA/GGBS ratios (7:3, 6:4, and 5:5) and PP fiber replacement ratios (0%, 25%, 50%, 75%, and 100%), investigated the influence of FA/GGBS and PP fiber replacement ratio on static mechanical behavior, and evaluated the economic and environmental benefits based on mechanical performance indicators. The result indicated that the compressive strength of H-EGCs can reach 120 MPa when the FA/GGBS ratio is 5:5; however, an increase in FA/GGBS and PP fiber replacement ratio leads to a loss in compressive strength and elastic modulus. The incorporation of PP fibers in moderate amounts enhances ultimate tensile strain by reducing crack control ability, and the maximum tensile deformation capacity (7.82–9.66%) was obtained for H-EGCs with a PP fiber replacement ratio of 50%. The optimal economic and environmental benefits of H-EGCs are observed when the FA/GGBS ratio is 5:5 and the PP fiber replacement ratio is set at 50%.