Baidehish Sahoo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Baidehish Sahoo has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Jinu Paul
Department of Mechanical Engineering, National Institute of Technology Calicut, Calicut, India
5 shared publications Jinu Paul
Department of Mechanical Engineering, National Institute of Technology Calicut, Calicut, 673601, India
3 shared publicationsTanmoy Das
Department of Mechanical Engineering, Indian Institute of Technology Kharagpur, Kharagpur, 721302, India
3 shared publications- Abhishek Sharma
Joining and Welding Research Institute, The University of Osaka
2 shared publications Abhishek Sharma
1 shared publication- Jomy Joseph
Indian Institute of Technology
1 shared publication
Latest Publications
- Open Access
- 18 April 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (4) , 139
Mechanical and Tribological Behaviour of Surface-Graphitised Al-1100 Alloy
This study details the mechanical incorporation of graphite particles into the surface of aluminium (Al-1100) to fabricate surface composites using an electrical resistance heating-assisted pressing method. Initially, the aluminium surface is coated with graphite via solution casting. Incorporation is accomplished by locally heating the graphite–aluminium interface with electrical resistance heating and subsequent mechanical pressure application. The magnitude of softening of the aluminium surface can be regulated by process considerations such as the applied current and heating duration. Microstructural assessment of the aluminium–graphite composite was conducted using SEM, TEM, Raman spectroscopy, and XRD. The surface mechanical properties and reduced Young’s modulus were improved by more than 200% and 150%, respectively. A detailed tribological study was conducted, and the study suggested that the wear resistance and COF improved by more than 50%. The progress in wear resistance and COF is corroborated by the microstructural changes in the matrix suggested by the Raman spectroscopy and XRD results.
- 18 April 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (4) , 139
Open AccessMechanical and Tribological Behaviour of Surface-Graphitised Al-1100 Alloy
This study details the mechanical incorporation of graphite particles into the surface of aluminium (Al-1100) to fabricate surface composites using an electrical resistance heating-assisted pressing method. Initially, the aluminium surface is coated with graphite via solution casting. Incorporation is accomplished by locally heating the graphite–aluminium interface with electrical resistance heating and subsequent mechanical pressure application. The magnitude of softening of the aluminium surface can be regulated by process considerations such as the applied current and heating duration. Microstructural assessment of the aluminium–graphite composite was conducted using SEM, TEM, Raman spectroscopy, and XRD. The surface mechanical properties and reduced Young’s modulus were improved by more than 200% and 150%, respectively. A detailed tribological study was conducted, and the study suggested that the wear resistance and COF improved by more than 50%. The progress in wear resistance and COF is corroborated by the microstructural changes in the matrix suggested by the Raman spectroscopy and XRD results.
- 25 March 2024
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 31 (11)
INVESTIGATION OF MICROSTRUCTURAL EVOLUTION AND MECHANICAL PROPERTIES OF SURFACE GRAPHITIZED AL-1100 ALLOY
This paper explains about the mechanical insertion of graphite particles into aluminum (Al-1100) surface for forming composites on the surface through an electrical resistance heat-supported pressing procedure. The surface of the aluminum is first graphite coated by solution casting. To achieve impregnation, the graphite–aluminum interface is locally heated with the assistance of electrical resistance heating followed by mechanical pushing. The degree to which aluminum surface softens can be regulated by process factors like current and heating time. Microstructural characterization of aluminum–graphite composite was carried out with SEM, TEM, Raman spectroscopy and XRD. It was revealed from the microstructural characterization that graphite particles were impregnated into the aluminum surface without agglomeration. Raman spectroscopy of graphite-impregnated surface shows a shift in major graphite peaks and an increased ratio of intensity ([ ]). The presence of carbide compound (Al4C3) was not detected from the XRD and TEM studies. The mechanical property examination of the surface was carried out by nanoindentation and the subsurface was characterized by microhardness tests. It was observed that surface mechanical property and reduced Young’s modulus were improved by more than 200% and 150%, respectively. The projected method can be utilized as a surface modification technique in solid-state by fabricating surface composites fabricated through mechanical insertion of particulate reinforcement at sub-melting temperatures of substrate and under an open producing environment.
- 25 March 2024
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 31 (11)
INVESTIGATION OF MICROSTRUCTURAL EVOLUTION AND MECHANICAL PROPERTIES OF SURFACE GRAPHITIZED AL-1100 ALLOY
This paper explains about the mechanical insertion of graphite particles into aluminum (Al-1100) surface for forming composites on the surface through an electrical resistance heat-supported pressing procedure. The surface of the aluminum is first graphite coated by solution casting. To achieve impregnation, the graphite–aluminum interface is locally heated with the assistance of electrical resistance heating followed by mechanical pushing. The degree to which aluminum surface softens can be regulated by process factors like current and heating time. Microstructural characterization of aluminum–graphite composite was carried out with SEM, TEM, Raman spectroscopy and XRD. It was revealed from the microstructural characterization that graphite particles were impregnated into the aluminum surface without agglomeration. Raman spectroscopy of graphite-impregnated surface shows a shift in major graphite peaks and an increased ratio of intensity ([ ]). The presence of carbide compound (Al4C3) was not detected from the XRD and TEM studies. The mechanical property examination of the surface was carried out by nanoindentation and the subsurface was characterized by microhardness tests. It was observed that surface mechanical property and reduced Young’s modulus were improved by more than 200% and 150%, respectively. The projected method can be utilized as a surface modification technique in solid-state by fabricating surface composites fabricated through mechanical insertion of particulate reinforcement at sub-melting temperatures of substrate and under an open producing environment.
- Open Access
- 22 July 2023
- Published by Elsevier in Results in Surfaces and Interfaces
- Vol. 12
Effect of ball milling and subsequent size reduction of graphite flakes on the surface mechanical properties of graphitized Al-1100 alloy
- 22 July 2023
- Published by Elsevier in Results in Surfaces and Interfaces
- Vol. 12
Open AccessEffect of ball milling and subsequent size reduction of graphite flakes on the surface mechanical properties of graphitized Al-1100 alloy
- 12 May 2022
- Published by Informatics Publishing Limited in Journal of Surface Science and Technology
- Vol. 37 (1-2) , 01-14
Anodising and Plasma Electrolytic Oxidation for the Surface Modification of Aluminium Alloys: Review
Aluminium (Al) and its alloys are attractive for a variety of applications due to its advantages like light weight, ease of processing and high thermal/electrical conductivities. However, it suffers from shortcomings in terms of strength, wear resistance and corrosion resistance. Anodising is commonly used to improve the surface modification of Al alloys. This paper presents a review of anodising and related processes and updates the current status in this area. The chemical structure and the size of the oxide film are influenced by factors like temperature, type of electrolyte and current density/ applied voltage. Depending on the process parameters, the oxide film formed in this process can be thin, non-porous, thick, and porous. The hardness of the coating in anodizing is influenced by the parameters like coating thickness, voltage, current density, and temperature. Further, it is required to regulate the metal/oxide or film/solution interface at which the barrier film grows. In Plasma Electrolytic Oxidation (PEO), the modified version of anodising, and the selection of operating conditions influence coating morphology, structure and composition which in turn affect the wear resistance and corrosion properties. The properties of the coating in case of PEO process are influenced by the nature/structure of the base material, type/composition of electrolyte, temperature of the electrolyte during the process, oxidation time, and electrical parameter (current density and voltage). Understanding of the effect of these parameters on coating properties opens new vista for better application prospects.
- 12 May 2022
- Published by Informatics Publishing Limited in Journal of Surface Science and Technology
- Vol. 37 (1-2) , 01-14
Anodising and Plasma Electrolytic Oxidation for the Surface Modification of Aluminium Alloys: Review
Aluminium (Al) and its alloys are attractive for a variety of applications due to its advantages like light weight, ease of processing and high thermal/electrical conductivities. However, it suffers from shortcomings in terms of strength, wear resistance and corrosion resistance. Anodising is commonly used to improve the surface modification of Al alloys. This paper presents a review of anodising and related processes and updates the current status in this area. The chemical structure and the size of the oxide film are influenced by factors like temperature, type of electrolyte and current density/ applied voltage. Depending on the process parameters, the oxide film formed in this process can be thin, non-porous, thick, and porous. The hardness of the coating in anodizing is influenced by the parameters like coating thickness, voltage, current density, and temperature. Further, it is required to regulate the metal/oxide or film/solution interface at which the barrier film grows. In Plasma Electrolytic Oxidation (PEO), the modified version of anodising, and the selection of operating conditions influence coating morphology, structure and composition which in turn affect the wear resistance and corrosion properties. The properties of the coating in case of PEO process are influenced by the nature/structure of the base material, type/composition of electrolyte, temperature of the electrolyte during the process, oxidation time, and electrical parameter (current density and voltage). Understanding of the effect of these parameters on coating properties opens new vista for better application prospects.
- Open Access
- 24 June 2019
- Published by Springer Nature in Bulletin of Materials Science
- Vol. 42 (5) , 204
Effect of exfoliated few-layered graphene on corrosion and mechanical behaviour of the graphitized Al–SiC surface composite fabricated by FSP
- 24 June 2019
- Published by Springer Nature in Bulletin of Materials Science
- Vol. 42 (5) , 204
Open AccessEffect of exfoliated few-layered graphene on corrosion and mechanical behaviour of the graphitized Al–SiC surface composite fabricated by FSP
- 1 October 2018
- Published by Elsevier in Materialia
- Vol. 2, 196-207
Solid state processed Al-1100 alloy/MWCNT surface nanocomposites
- 1 October 2018
- Published by Elsevier in Materialia
- Vol. 2, 196-207
Solid state processed Al-1100 alloy/MWCNT surface nanocomposites
- 1 March 2018
- Published by Elsevier in Surface and Coatings Technology
- Vol. 337, 12-23
Surface modification of Al6061 by graphene impregnation through a powder metallurgy assisted friction surfacing
- 1 March 2018
- Published by Elsevier in Surface and Coatings Technology
- Vol. 337, 12-23
Surface modification of Al6061 by graphene impregnation through a powder metallurgy assisted friction surfacing