Abhishek Sharma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Abhishek Sharma has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
Yoshiaki Morisada
7 shared publications- Hidetoshi Fujii
Joining and Welding Research Institute, The University of Osaka
5 shared publications Kohsaku Ushioda
5 shared publicationsHidetoshi Fujii
4 shared publications- Jinu Paul
Department of Mechanical Engineering, National Institute of Technology Calicut, Calicut, India
3 shared publications - Baidehish Sahoo
Department of Mechanical Engineering, Dr. Vishwanath Karad MIT World Peace University, Pune, Maharashtra, 411038, India
2 shared publications
Latest Publications
- Open Access
- 27 May 2026
- Published by Elsevier in Materials & Design
- Vol. 267
Linear friction welding of Haynes 282 Ni superalloy
- 27 May 2026
- Published by Elsevier in Materials & Design
- Vol. 267
Open AccessLinear friction welding of Haynes 282 Ni superalloy
- Open Access
- 15 December 2025
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 111 (17) , 1035-1045
Tilted-tool Friction Stir Welding of Steel Material by using Hemispherical Silicon Nitride Tool
Silicon nitride is one of the inexpensive and attractive tool materials for friction stir welding (FSW) of steel material. The improvement of silicon nitride tool life has been studied by controlling welding conditions and the tool geometry. In this study, the tool life of a hemispherical silicon nitride tool tilted toward the retreating side during FSW of steel plate was investigated. The defect-free welded SPHC plate was obtained using the hemispherical silicon nitride tool under the optimum welding condition. The tool life was evaluated at tool rotation speeds of 400, 500 and 700 rpm. At 400 rpm, the tool broke at a welding distance of 100 mm. At 700 rpm, the tool wear was observed at the welding distance of 3.0 m, and the tool broke before reaching the welding distance of 6.0 m. In contrast, at 500 rpm, tool wear or tool breakage was not observed up to the welding distance of 10.0 m. The tool life of the hemispherical silicon nitride tool strongly relates to the welding condition. The temperature of the hemispheric silicon nitride tool was 1078 K at the tool rotation speed of 500 rpm. Tool wear depends on the high temperature strength of the silicon nitride. The use of a simple shape such as the hemispherical tool allows FSW to perform at relatively low temperatures, which prevents tool wear and tool breakage.
- 15 December 2025
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 111 (17) , 1035-1045
Open AccessTilted-tool Friction Stir Welding of Steel Material by using Hemispherical Silicon Nitride Tool
Silicon nitride is one of the inexpensive and attractive tool materials for friction stir welding (FSW) of steel material. The improvement of silicon nitride tool life has been studied by controlling welding conditions and the tool geometry. In this study, the tool life of a hemispherical silicon nitride tool tilted toward the retreating side during FSW of steel plate was investigated. The defect-free welded SPHC plate was obtained using the hemispherical silicon nitride tool under the optimum welding condition. The tool life was evaluated at tool rotation speeds of 400, 500 and 700 rpm. At 400 rpm, the tool broke at a welding distance of 100 mm. At 700 rpm, the tool wear was observed at the welding distance of 3.0 m, and the tool broke before reaching the welding distance of 6.0 m. In contrast, at 500 rpm, tool wear or tool breakage was not observed up to the welding distance of 10.0 m. The tool life of the hemispherical silicon nitride tool strongly relates to the welding condition. The temperature of the hemispheric silicon nitride tool was 1078 K at the tool rotation speed of 500 rpm. Tool wear depends on the high temperature strength of the silicon nitride. The use of a simple shape such as the hemispherical tool allows FSW to perform at relatively low temperatures, which prevents tool wear and tool breakage.
- Open Access
- 25 October 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Microstructural evolution and mechanical behavior of friction stir welded additively manufactured Haynes 282 Ni superalloy
- 25 October 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Open AccessMicrostructural evolution and mechanical behavior of friction stir welded additively manufactured Haynes 282 Ni superalloy
- Open Access
- 27 July 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-17
Precision control of microstructure variation and tensile properties in dissimilar friction stir lap welding joints using an adjustable tool
Friction-assisted plastic deformation at the joint interface is essential for achieving the desired joint properties in dissimilar friction stir lap welding (FSLW) of aluminum alloy (Al) with steel (Fe). This plastic deformation can be precisely controlled by using an adjustable tool, where shoulder and probe rotation speeds are independently controlled. This study explores the effect of microstructure evolution and probe rotation speed on the weld’s interface morphology and tensile properties of FSLW joints between an aluminum alloy and steel using an adjustable tool. Microstructure evolution is influenced by inherent material properties and process-induced stress inhomogeneity. Grain refinement in Fe is more gradual compared to Al, which exhibits a homogenous microstructure. Lower probe rotation speeds lead to more significant grain refinement in Al, while increasing probe rotation speeds promote the formation of intermetallic compounds. An intercalated structure with varying fractions and morphology is observed across the joint interface in all welds. The controlled evolution of microstructure and the differences in intercalated structure formation at the weld interface are attributed to variations in shear strength. This study demonstrates the ability of an adjustable tool to tailor the microstructure and tensile properties of FSLW joints, providing a promising approach for enhancing joint performance in dissimilar metal joining applications.
- 27 July 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-17
Open AccessPrecision control of microstructure variation and tensile properties in dissimilar friction stir lap welding joints using an adjustable tool
Friction-assisted plastic deformation at the joint interface is essential for achieving the desired joint properties in dissimilar friction stir lap welding (FSLW) of aluminum alloy (Al) with steel (Fe). This plastic deformation can be precisely controlled by using an adjustable tool, where shoulder and probe rotation speeds are independently controlled. This study explores the effect of microstructure evolution and probe rotation speed on the weld’s interface morphology and tensile properties of FSLW joints between an aluminum alloy and steel using an adjustable tool. Microstructure evolution is influenced by inherent material properties and process-induced stress inhomogeneity. Grain refinement in Fe is more gradual compared to Al, which exhibits a homogenous microstructure. Lower probe rotation speeds lead to more significant grain refinement in Al, while increasing probe rotation speeds promote the formation of intermetallic compounds. An intercalated structure with varying fractions and morphology is observed across the joint interface in all welds. The controlled evolution of microstructure and the differences in intercalated structure formation at the weld interface are attributed to variations in shear strength. This study demonstrates the ability of an adjustable tool to tailor the microstructure and tensile properties of FSLW joints, providing a promising approach for enhancing joint performance in dissimilar metal joining applications.
- Open Access
- 2 July 2025
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 343
Elucidating the role of ordered phases and carbides in the mechanical performance of friction stir welded high aluminum low-density ferrite steels
- 2 July 2025
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 343
Open AccessElucidating the role of ordered phases and carbides in the mechanical performance of friction stir welded high aluminum low-density ferrite steels
- Open Access
- 13 November 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-13
Friction stir welding of Haynes 282 Ni superalloy by using a novel hemispherical tool
In the present investigation, friction stir welding (FSW) of a gamma prime (γ′) strengthened Haynes 282 nickel-base superalloy by using a novel hemispherical tool is documented. A joint efficiency of ~ 96% was achieved in the as-welded condition, which further increased to ~ 100% after two-step post-weld aging heat treatment. An extremely fine (~ 2 μm) grained microstructure was observed in the FSWed region compared with the coarse (~ 48 μm) grain base metal region. The carbides (MC and M23C6) and γ′ precipitates are identified as the important microstructural constituent phases observed in the welded region. The aging heat treatment resulted in the precipitation of the γ′ strengthening phase and altered the morphology of the M23C6 carbide phase in the welded region from a continuous film to discrete particles at the grain boundaries. The preliminary results concerning tool life suggest that no significant tool wear occurs at least up to a welding distance of 200 mm. Therefore, the novel hemispherical tool design allows the successful FSW of high-temperature application materials without any significant tool wear or high heat generation.
- 13 November 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-13
Open AccessFriction stir welding of Haynes 282 Ni superalloy by using a novel hemispherical tool
In the present investigation, friction stir welding (FSW) of a gamma prime (γ′) strengthened Haynes 282 nickel-base superalloy by using a novel hemispherical tool is documented. A joint efficiency of ~ 96% was achieved in the as-welded condition, which further increased to ~ 100% after two-step post-weld aging heat treatment. An extremely fine (~ 2 μm) grained microstructure was observed in the FSWed region compared with the coarse (~ 48 μm) grain base metal region. The carbides (MC and M23C6) and γ′ precipitates are identified as the important microstructural constituent phases observed in the welded region. The aging heat treatment resulted in the precipitation of the γ′ strengthening phase and altered the morphology of the M23C6 carbide phase in the welded region from a continuous film to discrete particles at the grain boundaries. The preliminary results concerning tool life suggest that no significant tool wear occurs at least up to a welding distance of 200 mm. Therefore, the novel hemispherical tool design allows the successful FSW of high-temperature application materials without any significant tool wear or high heat generation.
- 24 May 2024
- Published by Taylor & Francis
Recent Advances in Material, Manufacturing, and Machine Learning
The main aim of the 2nd international conference on recent advances in materials manufacturing and machine learning processes-2023 (RAMMML-23) is to bring together all interested academic researchers, scientists, engineers, and technocrats and provide a platform for continuous improvement of manufactur□ing, machine learning, design and materials engineering research. RAMMML 2023 received an overwhelm□ing response with more than 530 full paper submissions. After due and careful scrutiny, about 120 of them have been selected for presentation. The papers submitted have been reviewed by experts from renowned institutions, and subsequently, the authors have revised the papers, duly incorporating the suggestions of the reviewers. This has led to significant improvement in the quality of the contributions, Taylor & Francis publications, CRC Press have agreed to publish the selected proceedings of the conference in their book series of Advances in Mechanical Engineering and Interdisciplinary Sciences. This enables fast dissemina□tion of the papers worldwide and increases the scope of visibility for the research contributions of the authors.
- 24 May 2024
- Published by Taylor & Francis
Recent Advances in Material, Manufacturing, and Machine Learning
The main aim of the 2nd international conference on recent advances in materials manufacturing and machine learning processes-2023 (RAMMML-23) is to bring together all interested academic researchers, scientists, engineers, and technocrats and provide a platform for continuous improvement of manufactur□ing, machine learning, design and materials engineering research. RAMMML 2023 received an overwhelm□ing response with more than 530 full paper submissions. After due and careful scrutiny, about 120 of them have been selected for presentation. The papers submitted have been reviewed by experts from renowned institutions, and subsequently, the authors have revised the papers, duly incorporating the suggestions of the reviewers. This has led to significant improvement in the quality of the contributions, Taylor & Francis publications, CRC Press have agreed to publish the selected proceedings of the conference in their book series of Advances in Mechanical Engineering and Interdisciplinary Sciences. This enables fast dissemina□tion of the papers worldwide and increases the scope of visibility for the research contributions of the authors.
- Open Access
- 18 April 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (4) , 139
Mechanical and Tribological Behaviour of Surface-Graphitised Al-1100 Alloy
This study details the mechanical incorporation of graphite particles into the surface of aluminium (Al-1100) to fabricate surface composites using an electrical resistance heating-assisted pressing method. Initially, the aluminium surface is coated with graphite via solution casting. Incorporation is accomplished by locally heating the graphite–aluminium interface with electrical resistance heating and subsequent mechanical pressure application. The magnitude of softening of the aluminium surface can be regulated by process considerations such as the applied current and heating duration. Microstructural assessment of the aluminium–graphite composite was conducted using SEM, TEM, Raman spectroscopy, and XRD. The surface mechanical properties and reduced Young’s modulus were improved by more than 200% and 150%, respectively. A detailed tribological study was conducted, and the study suggested that the wear resistance and COF improved by more than 50%. The progress in wear resistance and COF is corroborated by the microstructural changes in the matrix suggested by the Raman spectroscopy and XRD results.
- 18 April 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (4) , 139
Open AccessMechanical and Tribological Behaviour of Surface-Graphitised Al-1100 Alloy
This study details the mechanical incorporation of graphite particles into the surface of aluminium (Al-1100) to fabricate surface composites using an electrical resistance heating-assisted pressing method. Initially, the aluminium surface is coated with graphite via solution casting. Incorporation is accomplished by locally heating the graphite–aluminium interface with electrical resistance heating and subsequent mechanical pressure application. The magnitude of softening of the aluminium surface can be regulated by process considerations such as the applied current and heating duration. Microstructural assessment of the aluminium–graphite composite was conducted using SEM, TEM, Raman spectroscopy, and XRD. The surface mechanical properties and reduced Young’s modulus were improved by more than 200% and 150%, respectively. A detailed tribological study was conducted, and the study suggested that the wear resistance and COF improved by more than 50%. The progress in wear resistance and COF is corroborated by the microstructural changes in the matrix suggested by the Raman spectroscopy and XRD results.
- 15 March 2024
- Published by Elsevier in Materialia
- Vol. 34
Elucidation of the factors controlling interface decohesion and particle fracture in a friction stir alloyed Al‒Fe alloy system
- 15 March 2024
- Published by Elsevier in Materialia
- Vol. 34
Elucidation of the factors controlling interface decohesion and particle fracture in a friction stir alloyed Al‒Fe alloy system
- 16 June 2023
- Published by Taylor & Francis
- p. 283-300
Collateral-based system for lending and renting of NFTs
Swift advances in technology are occurring every day, but equally rapidly becoming more prominent is the problem of centralization. There is strong demand for well-defined, decentralized solutions, for example, for trusting companies to keep our data safe and banks to keep our money safe. Blockchain, offering both functionalities, is a perfect solution to this issue. The blockchain is a digital platform with, at its core, a shared transaction ledger across a decentralized network. This ledger holds an immutable history of digital transactions affirmed by peer-to-peer consensus. Blockchains are built on open-source software, allowing developers to ensure the safety and security of transactions by avoiding third-party governance and interference by a central authority. This project focuses on the different categories of tokens available, which are of two types: fungible tokens and non-fungible tokens (NFTs). NFTs are now to be found everywhere, from classroom discussions to multinational companies. While these developments are exciting, the skyrocketing prices of NFTs makes them difficult to follow, especially for people of average financial status. Moreover, most of the NFTs purchased end up sitting idle in the owner’s wallet, i.e., without generating any yield for the owner. The object of this project, therefore, is to develop “smart contracts” for lending and renting NFTs.
- 16 June 2023
- Published by Taylor & Francis
- p. 283-300
Collateral-based system for lending and renting of NFTs
Swift advances in technology are occurring every day, but equally rapidly becoming more prominent is the problem of centralization. There is strong demand for well-defined, decentralized solutions, for example, for trusting companies to keep our data safe and banks to keep our money safe. Blockchain, offering both functionalities, is a perfect solution to this issue. The blockchain is a digital platform with, at its core, a shared transaction ledger across a decentralized network. This ledger holds an immutable history of digital transactions affirmed by peer-to-peer consensus. Blockchains are built on open-source software, allowing developers to ensure the safety and security of transactions by avoiding third-party governance and interference by a central authority. This project focuses on the different categories of tokens available, which are of two types: fungible tokens and non-fungible tokens (NFTs). NFTs are now to be found everywhere, from classroom discussions to multinational companies. While these developments are exciting, the skyrocketing prices of NFTs makes them difficult to follow, especially for people of average financial status. Moreover, most of the NFTs purchased end up sitting idle in the owner’s wallet, i.e., without generating any yield for the owner. The object of this project, therefore, is to develop “smart contracts” for lending and renting NFTs.