Kyung Gook Cho
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kyung Gook Cho has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Keun Hyung Lee
Department of Chemistry and Chemical Engineering Education and Research Center For Smart Energy and Materials Inha University Incheon Republic of Korea
5 shared publications Min Su Kim
Department of Chemistry and Chemical Engineering Education and Research Center For Smart Energy and Materials Inha University Incheon Republic of Korea
4 shared publications- Hyun Kim
Korea Research Institute of Chemical Technology
3 shared publications - C. Daniel Frisbie
Department of Chemical Engineering and Materials Science, University of Minnesota, Minneapolis, USA
2 shared publications Changsoon Choi
Department of Electronic Engineering and Biomedical Engineering Hanyang University Seoul Republic of Korea
2 shared publicationsDong Hyun Park
Department of Chemistry and Chemical Engineering Education and Research Center For Smart Energy and Materials Inha University Incheon Republic of Korea
2 shared publications
Latest Publications
- Open Access
- 21 August 2026
- Published by Wiley in Advanced Materials Technologies
- Vol. 11 (20) , e71268
Dynamic Disulfide Ionogels for Self‐Healing, Transparent, and Elastic E‐Skins
Ionogel E‐skins that combine high elasticity, optical transparency, and autonomous self‐healing are highly desirable yet remain challenging to realize owing to the intricate and interdependent physicochemical interactions between polymer networks and ionic liquids. Here, dynamic covalent ionogels, formed by a disulfide–crosslinked tetra‐arm polyethylene glycol network, were systematically engineered by tuning the identity and composition of ionic liquids. We show that polymer–ionic liquid compatibility, viscosity, and ionic liquid content collectively regulate polymer segmental mobility, which governs disulfide exchange kinetics and thereby dictates healing efficiency and elasticity. The optimized ionogel is fully amorphous and exhibits 99% self‐healing at 25°C within 2 h, a low residual strain of 1.7% after a 100% cyclic tensile test, and 93% optical transmittance at 700 nm. As an ionogel electronic skin, it maintains stable sensing under repeated deformation, recovers its initial functionality after complete damage through self‐healing, and enables reliable real‐time strain sensing of the neck, wrist, finger, and knee. These findings establish chain‐mobility engineering as an effective design principle for robust wearable ionogel electronics.
- 21 August 2026
- Published by Wiley in Advanced Materials Technologies
- Vol. 11 (20) , e71268
Open AccessDynamic Disulfide Ionogels for Self‐Healing, Transparent, and Elastic E‐Skins
Ionogel E‐skins that combine high elasticity, optical transparency, and autonomous self‐healing are highly desirable yet remain challenging to realize owing to the intricate and interdependent physicochemical interactions between polymer networks and ionic liquids. Here, dynamic covalent ionogels, formed by a disulfide–crosslinked tetra‐arm polyethylene glycol network, were systematically engineered by tuning the identity and composition of ionic liquids. We show that polymer–ionic liquid compatibility, viscosity, and ionic liquid content collectively regulate polymer segmental mobility, which governs disulfide exchange kinetics and thereby dictates healing efficiency and elasticity. The optimized ionogel is fully amorphous and exhibits 99% self‐healing at 25°C within 2 h, a low residual strain of 1.7% after a 100% cyclic tensile test, and 93% optical transmittance at 700 nm. As an ionogel electronic skin, it maintains stable sensing under repeated deformation, recovers its initial functionality after complete damage through self‐healing, and enables reliable real‐time strain sensing of the neck, wrist, finger, and knee. These findings establish chain‐mobility engineering as an effective design principle for robust wearable ionogel electronics.
- Open Access
- 11 August 2026
- Published by Wiley in Advanced Robotics Research
- Vol. 2 (4) , e70149
Inside Back Cover: Advances in Electroactive Liquid Crystal Elastomers for Intelligent Robotics and Electronics (Adv. Robotics Res. 4/2026)
- 11 August 2026
- Published by Wiley in Advanced Robotics Research
- Vol. 2 (4) , e70149
Open AccessInside Back Cover: Advances in Electroactive Liquid Crystal Elastomers for Intelligent Robotics and Electronics (Adv. Robotics Res. 4/2026)
- Open Access
- 28 April 2026
- Published by Wiley in Advanced Robotics Research
- Vol. 2 (4)
Advances in Electroactive Liquid Crystal Elastomers for Intelligent Robotics and Electronics
Electroactive liquid crystal elastomers (eLCEs) represent a rapidly emerging class of intelligent soft materials that integrate molecular anisotropy with electrical functionality. In this review, we classify eLCEs into two major subcategories: (i) robotic actuators, which enable programmable and reversible deformation in response to electrical stimuli, and (ii) adaptive electronics, which realize programmed morphing or functional reconfiguration. By coupling the orientational order of liquid crystals with the elasticity of polymer networks, robotic eLCEs convert electrical energy into mechanical actuation through diverse mechanisms, including electrothermal, electromechanical, electrostatic, and electrochemical pathways. In addition, electronic eLCEs primarily function as morphing substrates capable of controlled shape transformation, enabling reconfigurable electronic systems such as stretchable conductors, sensing antennas, and neural interfaces. To guide the field, this review provides an overview of activation mechanisms in eLCEs, followed by representative robotic and electronic applications with an emphasis on fabrication strategies that bridge material‐level advances toward next‐generation intelligent devices. Collectively, these advances highlight the significant potential of eLCEs for future soft robotics, adaptive electronics, and dynamic interface systems.
- 28 April 2026
- Published by Wiley in Advanced Robotics Research
- Vol. 2 (4)
Open AccessAdvances in Electroactive Liquid Crystal Elastomers for Intelligent Robotics and Electronics
Electroactive liquid crystal elastomers (eLCEs) represent a rapidly emerging class of intelligent soft materials that integrate molecular anisotropy with electrical functionality. In this review, we classify eLCEs into two major subcategories: (i) robotic actuators, which enable programmable and reversible deformation in response to electrical stimuli, and (ii) adaptive electronics, which realize programmed morphing or functional reconfiguration. By coupling the orientational order of liquid crystals with the elasticity of polymer networks, robotic eLCEs convert electrical energy into mechanical actuation through diverse mechanisms, including electrothermal, electromechanical, electrostatic, and electrochemical pathways. In addition, electronic eLCEs primarily function as morphing substrates capable of controlled shape transformation, enabling reconfigurable electronic systems such as stretchable conductors, sensing antennas, and neural interfaces. To guide the field, this review provides an overview of activation mechanisms in eLCEs, followed by representative robotic and electronic applications with an emphasis on fabrication strategies that bridge material‐level advances toward next‐generation intelligent devices. Collectively, these advances highlight the significant potential of eLCEs for future soft robotics, adaptive electronics, and dynamic interface systems.
- Open Access
- 12 February 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (44)
Regiorandom Polythiophenes for Fully Stretchable Electrochemical Transistors and Logic Circuits
Regiorandom (RRa) polythiophenes have long been considered unsuitable for highperformance electronics owing to their poor molecular ordering and limited carrier transport. In this study, we demonstrate that RRa polythiophenes, when employed in organic electrochemical transistors (OECTs), exhibit unexpectedly efficient charge transport enabled by volumetric electrochemical doping. Among various alkyl side chains, RRa‐poly(3‐decylthiophene) (P3DT, C10) offers the optimal OECT performance, achieving an on‐state current of ≈160 µA in the saturation regime and an on/off ratio of ≈10 4 , which significantly surpasses the typical performance of disordered polymers. Remarkably, RRa‐P3DT maintains electrical characteristics under large strains of up to 200%, owing to its irregular structure. Fully stretchable OECTs were fabricated by integrating RRa‐P3DT with a single‐walled carbon nanotube (SWCNT) gate electrode and an ionogel electrolyte, retaining stable switching characteristics under 100% strain and occupying the upper‐right corner of the on/off ratio–stretchability plot, thereby outperforming most reported intrinsically stretchable OECTs. Moreover, the successful demonstration of stretchable logic gates including inverters, NAND, and NOR highlights the untapped potential of amorphous polymer semiconductors for stretchable electronics.
- 12 February 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (44)
Open AccessRegiorandom Polythiophenes for Fully Stretchable Electrochemical Transistors and Logic Circuits
Regiorandom (RRa) polythiophenes have long been considered unsuitable for highperformance electronics owing to their poor molecular ordering and limited carrier transport. In this study, we demonstrate that RRa polythiophenes, when employed in organic electrochemical transistors (OECTs), exhibit unexpectedly efficient charge transport enabled by volumetric electrochemical doping. Among various alkyl side chains, RRa‐poly(3‐decylthiophene) (P3DT, C10) offers the optimal OECT performance, achieving an on‐state current of ≈160 µA in the saturation regime and an on/off ratio of ≈10 4 , which significantly surpasses the typical performance of disordered polymers. Remarkably, RRa‐P3DT maintains electrical characteristics under large strains of up to 200%, owing to its irregular structure. Fully stretchable OECTs were fabricated by integrating RRa‐P3DT with a single‐walled carbon nanotube (SWCNT) gate electrode and an ionogel electrolyte, retaining stable switching characteristics under 100% strain and occupying the upper‐right corner of the on/off ratio–stretchability plot, thereby outperforming most reported intrinsically stretchable OECTs. Moreover, the successful demonstration of stretchable logic gates including inverters, NAND, and NOR highlights the untapped potential of amorphous polymer semiconductors for stretchable electronics.
- 28 February 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (10) , 15718-15727
Band Filling, Electrochemical Reaction, and Re-Entrant Insulating Behavior in Electrolyte-Gated BBL Polymer Semiconductor Films
Electrochemical doping of the n-type polymer poly(benzimidazobenzophenanthroline) (BBL) in contact with ionic liquids reveals a peak in the drain current (ID) vs gate voltage (VG) behavior, i.e., conductivity versus electron density. The conductivity peak is related to simultaneously acquired gate current-gate voltage (IG-VG) charging curves that are integrated to yield total charge accumulation. The IG-VG traces reveal three separate redox events upon charging BBL that can be correlated with the ID-VG behavior. We assign the first broad IG-VG peak to accumulation of mobile electrons in the BBL LUMO and an increase in ID. Two subsequent sharp IG-VG peaks correspond to electrochemical transformation of BBL to a polymer salt with 2:1 and 1:1 repeat unit-to-cation stoichiometries, respectively. Salt formation correlates with conductivity collapse at high VG; the 1:1 salt phase is insulating. Ex situ grazing incidence wide-angle X-ray scattering (GIWAXS) indicates an initial 5% contraction of the lamellar spacing upon doping with subsequent retention of lamellar (para)crystalline order for repeated doping cycles. Overall, our results reveal a complex interplay between band filling and electrochemical reaction in the transport behavior of electrochemically doped BBL films and provide additional evidence of nonmonotonic conductivity versus charge behavior that appears to be general in polymer semiconductor films.
- 28 February 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (10) , 15718-15727
Band Filling, Electrochemical Reaction, and Re-Entrant Insulating Behavior in Electrolyte-Gated BBL Polymer Semiconductor Films
Electrochemical doping of the n-type polymer poly(benzimidazobenzophenanthroline) (BBL) in contact with ionic liquids reveals a peak in the drain current (ID) vs gate voltage (VG) behavior, i.e., conductivity versus electron density. The conductivity peak is related to simultaneously acquired gate current-gate voltage (IG-VG) charging curves that are integrated to yield total charge accumulation. The IG-VG traces reveal three separate redox events upon charging BBL that can be correlated with the ID-VG behavior. We assign the first broad IG-VG peak to accumulation of mobile electrons in the BBL LUMO and an increase in ID. Two subsequent sharp IG-VG peaks correspond to electrochemical transformation of BBL to a polymer salt with 2:1 and 1:1 repeat unit-to-cation stoichiometries, respectively. Salt formation correlates with conductivity collapse at high VG; the 1:1 salt phase is insulating. Ex situ grazing incidence wide-angle X-ray scattering (GIWAXS) indicates an initial 5% contraction of the lamellar spacing upon doping with subsequent retention of lamellar (para)crystalline order for repeated doping cycles. Overall, our results reveal a complex interplay between band filling and electrochemical reaction in the transport behavior of electrochemically doped BBL films and provide additional evidence of nonmonotonic conductivity versus charge behavior that appears to be general in polymer semiconductor films.
- 6 January 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 35 (20)
Redox‐Enhanced Ionogels for Stretchable High‐Energy Density Electrochemical Capacitors
Developing stretchable energy storage devices with high energy and power densities poses a significant challenge for future wearable/deformable electronics. This study proposes new redox (R)‐ionogels that incorporate organodisulfides as redox species for high‐energy, stretchable redox‐enhanced solid‐state electrochemical capacitors (R‐SECs). The R‐SECs are prepared using R‐ionogels made from tetraethylthiuram disulfide (TETDS), 1‐ethyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide ([EMI][TFSI]), and a physically crosslinked polymer network (poly(vinylidene fluoride‐co‐hexafluoropropylene), P(VDF‐HFP)), sandwiched between two carbonaceous electrodes. Cyclic voltammetry and galvanostatic charge/discharge characteristics of the R‐SECs demonstrated both effective redox reactions and non‐faradaic capacitive energy storage. The optimized 0.25 M TETDS R‐ionogel achieved a specific capacitance of 405 F g‒1, 83% rate retention, 80% cyclic stability after 2000 cycles, an energy density of 117 Wh kg‒1, and a power density of 5.9 kW kg‒1. Additionally, the 0.25 M TETDS enhanced the mechanical properties of the ionogel, increasing the strain at break from 1.92 to 3.25 and toughness from 0.38 to 1.35 MJ m⁻3. Finally, stretchable R‐SECs possessing excellent stretching/releasing durability at 100% strain and volumetric energy densities 26.3 mWh cm−3 that surpass the upper bound of the Ragone plot for reported stretchable capacitors are successfully fabricated for the first time.
- 6 January 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 35 (20)
Redox‐Enhanced Ionogels for Stretchable High‐Energy Density Electrochemical Capacitors
Developing stretchable energy storage devices with high energy and power densities poses a significant challenge for future wearable/deformable electronics. This study proposes new redox (R)‐ionogels that incorporate organodisulfides as redox species for high‐energy, stretchable redox‐enhanced solid‐state electrochemical capacitors (R‐SECs). The R‐SECs are prepared using R‐ionogels made from tetraethylthiuram disulfide (TETDS), 1‐ethyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide ([EMI][TFSI]), and a physically crosslinked polymer network (poly(vinylidene fluoride‐co‐hexafluoropropylene), P(VDF‐HFP)), sandwiched between two carbonaceous electrodes. Cyclic voltammetry and galvanostatic charge/discharge characteristics of the R‐SECs demonstrated both effective redox reactions and non‐faradaic capacitive energy storage. The optimized 0.25 M TETDS R‐ionogel achieved a specific capacitance of 405 F g‒1, 83% rate retention, 80% cyclic stability after 2000 cycles, an energy density of 117 Wh kg‒1, and a power density of 5.9 kW kg‒1. Additionally, the 0.25 M TETDS enhanced the mechanical properties of the ionogel, increasing the strain at break from 1.92 to 3.25 and toughness from 0.38 to 1.35 MJ m⁻3. Finally, stretchable R‐SECs possessing excellent stretching/releasing durability at 100% strain and volumetric energy densities 26.3 mWh cm−3 that surpass the upper bound of the Ragone plot for reported stretchable capacitors are successfully fabricated for the first time.
- 9 April 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (15) , 19309-19317
Tuning Gate Potential Profiles and Current–Voltage Characteristics of Polymer Electrolyte-Gated Transistors by Capacitance Engineering
We demonstrate that the transfer characteristics of electrolyte-gated transistors (EGTs) with polythiophene semiconductor channels are a strong function of gate/electrolyte interfacial contact area, i.e., gate size. Polythiophene EGTs with gate/electrolyte areas much larger than the channel/electrolyte areas show a clear peak in the drain current vs gate voltage (ID–VG) behavior, as well as peak voltage hysteresis between the forward and reverse VG sweeps. Polythiophene EGTs with small gate/electrolyte areas, on the other hand, exhibit current plateaus in the ID–VG behavior and a gate-size-dependent hysteresis loop between turn on and off. The qualitatively different transport behaviors are attributed to the relative sizes of the gate/electrolyte and channel/electrolyte interface capacitances, which are proportional to interfacial area. These interfacial capacitances are in series with each other such that the total capacitance of the full gate/electrolyte/channel stack is dominated by the interface with the smallest capacitance or area. For EGTs with large gates, most of the applied VG is dropped at the channel/electrolyte interface, leading to very high charge accumulations, up to ∼0.3 holes per ring (hpr) in the case of polythiophene semiconductors. The large charge density results in sub-band-filling and a marked decrease in hole mobility, giving rise to the peak in ID–VG. For EGTs with small gates, hole accumulation saturates near 0.15 hpr, band-filling does not occur, and hole mobility is maintained at a fixed value, which leads to the ID plateau. Potential drops at the interfaces are confirmed by in situ potential measurements inside a gate/electrolyte/polymer semiconductor stack. Hole accumulations are measured with gate current-gate voltage (IG–VG) measurements acquired simultaneously with the ID–VG characteristics. Overall, our measurements demonstrate that remarkably different ID behavior can be obtained for polythiophene EGTs by controlling the magnitude of the gate-electrolyte interfacial capacitance.
- 9 April 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (15) , 19309-19317
Tuning Gate Potential Profiles and Current–Voltage Characteristics of Polymer Electrolyte-Gated Transistors by Capacitance Engineering
We demonstrate that the transfer characteristics of electrolyte-gated transistors (EGTs) with polythiophene semiconductor channels are a strong function of gate/electrolyte interfacial contact area, i.e., gate size. Polythiophene EGTs with gate/electrolyte areas much larger than the channel/electrolyte areas show a clear peak in the drain current vs gate voltage (ID–VG) behavior, as well as peak voltage hysteresis between the forward and reverse VG sweeps. Polythiophene EGTs with small gate/electrolyte areas, on the other hand, exhibit current plateaus in the ID–VG behavior and a gate-size-dependent hysteresis loop between turn on and off. The qualitatively different transport behaviors are attributed to the relative sizes of the gate/electrolyte and channel/electrolyte interface capacitances, which are proportional to interfacial area. These interfacial capacitances are in series with each other such that the total capacitance of the full gate/electrolyte/channel stack is dominated by the interface with the smallest capacitance or area. For EGTs with large gates, most of the applied VG is dropped at the channel/electrolyte interface, leading to very high charge accumulations, up to ∼0.3 holes per ring (hpr) in the case of polythiophene semiconductors. The large charge density results in sub-band-filling and a marked decrease in hole mobility, giving rise to the peak in ID–VG. For EGTs with small gates, hole accumulation saturates near 0.15 hpr, band-filling does not occur, and hole mobility is maintained at a fixed value, which leads to the ID plateau. Potential drops at the interfaces are confirmed by in situ potential measurements inside a gate/electrolyte/polymer semiconductor stack. Hole accumulations are measured with gate current-gate voltage (IG–VG) measurements acquired simultaneously with the ID–VG characteristics. Overall, our measurements demonstrate that remarkably different ID behavior can be obtained for polythiophene EGTs by controlling the magnitude of the gate-electrolyte interfacial capacitance.