D. A. Pupkova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
D. A. Pupkova has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Igor Nikolaevich Kravchenko
Mechanical Engineering Research Institute of the Russian Academy of Sciences, Moscow, Russia
2 shared publications - Nina Zh. Shkaruba
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
2 shared publications - Oleg A. Leonov
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
2 shared publications Timirâzevskaâ Selʹskohozâjstvennaâ Akademiâ
2 shared publications- И. Н. Кравченко
Российский государственный аграрный университет – МСХА имени К.А. Тимирязева
2 shared publications - D. U. Khasyanova
Mechanical Engineering Research Institute of the Russian Academy of Sciences, Moscow, Russia
1 shared publication
Latest Publications
- 1 September 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (9) , 1233-1237
Assessment of the Hardness of Hardened Mass-Produced Plow Blades by Lemken
The article considers the problem of increasing the service life of agricultural machinery tools under conditions of abrasive wear by using hardening techn
- 1 September 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (9) , 1233-1237
Assessment of the Hardness of Hardened Mass-Produced Plow Blades by Lemken
The article considers the problem of increasing the service life of agricultural machinery tools under conditions of abrasive wear by using hardening techn
- 1 September 2024
- Published by Allerton Press in Russian Engineering Research
- Vol. 44 (9) , 1240-1243
Improving the Reliability of Pipe End Joints Using Shape Memory
A technology is developed for connecting pipes by means of sleeves or fittings made of materials with shape memory. When using this technology, joints in p
- 1 September 2024
- Published by Allerton Press in Russian Engineering Research
- Vol. 44 (9) , 1240-1243
Improving the Reliability of Pipe End Joints Using Shape Memory
A technology is developed for connecting pipes by means of sleeves or fittings made of materials with shape memory. When using this technology, joints in p
- 1 February 2024
- Published by Allerton Press in Russian Engineering Research
- Vol. 44 (2) , 184-188
Calculation and Selection of Interference Fits for Restoring the Shaft Surface under the Sealing Ring by Pressing Thin-Walled Bushings
Methods for restoring shaft surfaces to nominal sizes are analyzed. It is recommended to use the thin-walled bushing method. The research used the principl
- 1 February 2024
- Published by Allerton Press in Russian Engineering Research
- Vol. 44 (2) , 184-188
Calculation and Selection of Interference Fits for Restoring the Shaft Surface under the Sealing Ring by Pressing Thin-Walled Bushings
Methods for restoring shaft surfaces to nominal sizes are analyzed. It is recommended to use the thin-walled bushing method. The research used the principl
- Open Access
- 1 January 2024
- Published by Russian State Agrarian University - Moscow Timiryazev Agricultural Academy in Agricultural engineering
- Vol. 26 (5) , 39-46
Assessment of the quality of the crankshaft grinding process for repair size
Mechanical processing of critical parts affects the quality of engine repair. The authors carried out research to assess the quality of setting for machining the crankshaft main journals of the ZMZ engine for the repair size. They studied the diameters of 20 crankshaft main journals of the ZMZ engine after machining for the repair size. The diameters were controlled by a lever clamp SR-75. The following tools were sequentially used to evaluate the quality of machining main bearing journals: a “box-and-whisker” diagram, Shewhart control charts, and a histogram. According to the “Box and Whiskers” diagram it was found that after machining for the repair size all the journals have a diameter within the machining tolerance field, but at the same time there is a scatter between the diameters of the journals of the same crankshaft. After analyzing the Shewhart control charts, it was found that the scatter values within one subgroup (crankshaft) and between the subgroups were caused by the usual reasons, and this scatter pattern can be considered random. Consequently, the technological process can be considered stable and controllable. The histogram helped to determine the probability of correctable rejects after machining of the engine journal for the repair size, equal to 1.95%, and the probability of irreparable rejects, equal to 0. The calculated reproducibility index of 0.93 indicates a significant wear of the equipment. Over time, the index will decrease and the risks of rejects will increase. The authors conclude that the quality of setting for machining crankshaft main bearing journals for the repair size is acceptable. It is desirable to regularly check the quality of machining crankshaft main journals for the repair size, consistently applying all the three tools to identify the size variation and inconsistencies, which is especially relevant for worn equipment.
- 1 January 2024
- Published by Russian State Agrarian University - Moscow Timiryazev Agricultural Academy in Agricultural engineering
- Vol. 26 (5) , 39-46
Open AccessAssessment of the quality of the crankshaft grinding process for repair size
Mechanical processing of critical parts affects the quality of engine repair. The authors carried out research to assess the quality of setting for machining the crankshaft main journals of the ZMZ engine for the repair size. They studied the diameters of 20 crankshaft main journals of the ZMZ engine after machining for the repair size. The diameters were controlled by a lever clamp SR-75. The following tools were sequentially used to evaluate the quality of machining main bearing journals: a “box-and-whisker” diagram, Shewhart control charts, and a histogram. According to the “Box and Whiskers” diagram it was found that after machining for the repair size all the journals have a diameter within the machining tolerance field, but at the same time there is a scatter between the diameters of the journals of the same crankshaft. After analyzing the Shewhart control charts, it was found that the scatter values within one subgroup (crankshaft) and between the subgroups were caused by the usual reasons, and this scatter pattern can be considered random. Consequently, the technological process can be considered stable and controllable. The histogram helped to determine the probability of correctable rejects after machining of the engine journal for the repair size, equal to 1.95%, and the probability of irreparable rejects, equal to 0. The calculated reproducibility index of 0.93 indicates a significant wear of the equipment. Over time, the index will decrease and the risks of rejects will increase. The authors conclude that the quality of setting for machining crankshaft main bearing journals for the repair size is acceptable. It is desirable to regularly check the quality of machining crankshaft main journals for the repair size, consistently applying all the three tools to identify the size variation and inconsistencies, which is especially relevant for worn equipment.
- 1 January 2023
- Published by Innovative Mashinostroenie Publishing
Tests of the disk intake device of a droplet refrigerator-emitter with blocking of reflected flows and optimization of the design
The results of tests of the intake device of the droplet refrigerator of the emitter of the thermal stabilization system of spacecraft power systems using droplet monodisperse flows are presented. Design optimization based on them is proposed. Keywords droplet refrigerator-emitter, thermal control of energy systems, cooling of spacecraft power plants
- 1 January 2023
- Published by Innovative Mashinostroenie Publishing
Tests of the disk intake device of a droplet refrigerator-emitter with blocking of reflected flows and optimization of the design
The results of tests of the intake device of the droplet refrigerator of the emitter of the thermal stabilization system of spacecraft power systems using droplet monodisperse flows are presented. Design optimization based on them is proposed. Keywords droplet refrigerator-emitter, thermal control of energy systems, cooling of spacecraft power plants
- Open Access
- 1 January 2023
- Published by Russian State Agrarian University - Moscow Timiryazev Agricultural Academy in Agricultural engineering
- Vol. 25 (5) , 73-77
Application of microwave energy to improve the safety indicators of raw grain
Применение СВЧ-энергии для улучшения показателей безопасности зернового сырья
- 1 January 2023
- Published by Russian State Agrarian University - Moscow Timiryazev Agricultural Academy in Agricultural engineering
- Vol. 25 (5) , 73-77
Open AccessApplication of microwave energy to improve the safety indicators of raw grain
Применение СВЧ-энергии для улучшения показателей безопасности зернового сырья