Ekaterina A. Ilicheva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ekaterina A. Ilicheva has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
- Polina K. Sukhorukova
LASE – Laboratory of Advanced Solar Energy , NUST MISIS, 119049 Moscow
7 shared publications - Danila Saranin
CERN
6 shared publications - Lev O. Luchnikov
LASE – Laboratory of Advanced Solar Energy NUST MISIS Moscow Russia
5 shared publications - Yuriy N. Luponosov
Enikolopov Institute of Synthetic Polymeric Materials of the Russian Academy of Sciences, Profsoyuznaya st. 70, Moscow 117393, Russia
5 shared publications - Anton A. Vasilev
National University of Science and Technology MISIS, Moscow 119049, Russia
4 shared publications - Dmitrii Yuryevich Dorofeev
Institute of New Materials, Research Technological University MISIS,Moskow,Russia
4 shared publications
Latest Publications
- Open Access
- 29 June 2026
- Published by Elsevier in SSRN Electronic Journal
Slot-die coated perovskite solar cells and modules with solvatophilic tri-functional self-assembling monolayers based on triphenylamine
The use of solution-processed self-assembled monolayers (SAMs) to passivate metal oxide thin films is an effective approach for high-performance perovskite solar cells. However, commonly used SAMs suffer from poor uniformity and wettability issues in ultrathin layers (1000 h, ISOS-L-2). Correlating local non-uniform wetting spots with lifetime, dark saturation current, and temperature coefficients reveals that mitigating SAM-induced wetting defects is essential for scalable, stable perovskite photovoltaics.
- 29 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSlot-die coated perovskite solar cells and modules with solvatophilic tri-functional self-assembling monolayers based on triphenylamine
The use of solution-processed self-assembled monolayers (SAMs) to passivate metal oxide thin films is an effective approach for high-performance perovskite solar cells. However, commonly used SAMs suffer from poor uniformity and wettability issues in ultrathin layers (1000 h, ISOS-L-2). Correlating local non-uniform wetting spots with lifetime, dark saturation current, and temperature coefficients reveals that mitigating SAM-induced wetting defects is essential for scalable, stable perovskite photovoltaics.
- Open Access
- 24 June 2026
- Published by Elsevier in SSRN Electronic Journal
Thermal Ionic Stability Under ISOS-D-2 Decouples Room-Temperature Efficiency from Durability in CsFAPbI3 Perovskite Solar Cells
Thermal performance of perovskite solar cells under elevated operating temperatures remains poorly understood, being one of the key bottlenecks for commercial deployment. While composition engineering has driven record power conversion efficiencies (PCEs), its impact on defect landscape and ionic transport stability is rarely quantified at the device level under harsh thermal stress (85°C). Here we compare two CsXFA1-XPbI₃ absorbers (x = 0.05 and 0.20) across structural, optical and ionic transport measurements under prolonged ISOS-D-2. Devices with reduced Cs concentration achieved PCE of 22.23% with high room-temperature recombination metrics, attributed to reduced lattice strain (ε = -0.00431) and charge carrier lifetimes. Temperature-coefficient measurements revealed that this advantage reverses under heating, with TPCE reaching -0.624%/°C versus -0.294%/°C for Cs 20%, driven by fill factor losses. Admittance and photo-induced spectroscopies resolved an increase in ion activation energy from 0.4 to >0.6 eV across Cs 5% and 20% compositions with different trends of diffusion coefficient. In Cs 20% devices, CsPbI3-rich cluster formation acted as an ionic sink, passivating active interfaces, while in Cs 5% devices unimpeded ion migration along grain boundaries affected charge collection efficiency. These findings establish that room-temperature efficiency and thermal ionic stability are decoupled parameters requiring independent compositional optimization.
- 24 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessThermal Ionic Stability Under ISOS-D-2 Decouples Room-Temperature Efficiency from Durability in CsFAPbI3 Perovskite Solar Cells
Thermal performance of perovskite solar cells under elevated operating temperatures remains poorly understood, being one of the key bottlenecks for commercial deployment. While composition engineering has driven record power conversion efficiencies (PCEs), its impact on defect landscape and ionic transport stability is rarely quantified at the device level under harsh thermal stress (85°C). Here we compare two CsXFA1-XPbI₃ absorbers (x = 0.05 and 0.20) across structural, optical and ionic transport measurements under prolonged ISOS-D-2. Devices with reduced Cs concentration achieved PCE of 22.23% with high room-temperature recombination metrics, attributed to reduced lattice strain (ε = -0.00431) and charge carrier lifetimes. Temperature-coefficient measurements revealed that this advantage reverses under heating, with TPCE reaching -0.624%/°C versus -0.294%/°C for Cs 20%, driven by fill factor losses. Admittance and photo-induced spectroscopies resolved an increase in ion activation energy from 0.4 to >0.6 eV across Cs 5% and 20% compositions with different trends of diffusion coefficient. In Cs 20% devices, CsPbI3-rich cluster formation acted as an ionic sink, passivating active interfaces, while in Cs 5% devices unimpeded ion migration along grain boundaries affected charge collection efficiency. These findings establish that room-temperature efficiency and thermal ionic stability are decoupled parameters requiring independent compositional optimization.
Enhanced Thermal Stability of Inverted Perovskite Solar Cells by Bulky Passivation With Pyridine‐Functionalized Triphenylamine
Despite competitive efficiency compared to Si solar cells and relevant stability at near room temperatures, the rapid degradation at elevated temperatures remains the critical obstacle for the exploitation of perovskite photovoltaics. In this work, a 4‐(pyridin‐4‐yl)triphenylamine (TPA‐Py) with pyridine anchor group was employed for intergrain bulk modification of double‐cation CsCH(NH 2 ) 2 PbI 3 perovskite absorbers to enhance thermal stability. Through coordination and dipole–dipole interactions, nitrogen‐containing fragments (diphenylamine and pyridine) of TPA‐Py passivate uncoordinated cations and improve the phase resilience of perovskite films against segregation. This resulted in a power conversion efficiency of 21.3% with a high open‐circuit voltage of 1.14 V. Notable impact of self‐assembled monolayer incorporated into the bulk of the perovskite film manifested in a huge improvement of thermal stability at 85°C (ISOS‐D‐2). TPA‐Py modification extended the T80 lifetime to ≈700 h compared to only 200 h for the reference under harsh heating stress in ambient conditions. In‐depth analysis using photoinduced voltage transients and admittance spectroscopy after different stress periods revealed the screening of ion migration (0.45 eV) for devices with TPA‐Py. This work offers an important understanding of the bulk modification of microcrystalline perovskite absorbers and a guide for robust design of bulk and buried interfaces in highly efficient perovskite solar cells.
Enhanced Thermal Stability of Inverted Perovskite Solar Cells by Bulky Passivation With Pyridine‐Functionalized Triphenylamine
Despite competitive efficiency compared to Si solar cells and relevant stability at near room temperatures, the rapid degradation at elevated temperatures remains the critical obstacle for the exploitation of perovskite photovoltaics. In this work, a 4‐(pyridin‐4‐yl)triphenylamine (TPA‐Py) with pyridine anchor group was employed for intergrain bulk modification of double‐cation CsCH(NH 2 ) 2 PbI 3 perovskite absorbers to enhance thermal stability. Through coordination and dipole–dipole interactions, nitrogen‐containing fragments (diphenylamine and pyridine) of TPA‐Py passivate uncoordinated cations and improve the phase resilience of perovskite films against segregation. This resulted in a power conversion efficiency of 21.3% with a high open‐circuit voltage of 1.14 V. Notable impact of self‐assembled monolayer incorporated into the bulk of the perovskite film manifested in a huge improvement of thermal stability at 85°C (ISOS‐D‐2). TPA‐Py modification extended the T80 lifetime to ≈700 h compared to only 200 h for the reference under harsh heating stress in ambient conditions. In‐depth analysis using photoinduced voltage transients and admittance spectroscopy after different stress periods revealed the screening of ion migration (0.45 eV) for devices with TPA‐Py. This work offers an important understanding of the bulk modification of microcrystalline perovskite absorbers and a guide for robust design of bulk and buried interfaces in highly efficient perovskite solar cells.
- 22 September 2025
- Published by Elsevier in Applied Surface Science
- Vol. 716
Stabilization of interfaces for double-cation halide perovskites with AVA2FAPb2I7 additives
- 22 September 2025
- Published by Elsevier in Applied Surface Science
- Vol. 716
Stabilization of interfaces for double-cation halide perovskites with AVA2FAPb2I7 additives