Zygmunt Mikno
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zygmunt Mikno has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Janusz Pikuła
Łukasiewicz Research Network – Upper Silesian Institute of Technology
4 shared publications - Mariusz Stepien
Department of Power Electronics, Electrical Drives and Robotics, Silesian University of Technology, Gliwice, Poland
3 shared publications - Paweł Kustroń
Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, Lukasiewicza 5, 50-371 Wroclaw, Poland
2 shared publications Maciej Karpiński
ASPA sp. z o.o., Wrocław University of Technology
1 shared publication- Maciej Karpiński
Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, Lukasiewicza 5, 50-371 Wroclaw, Poland
1 shared publication - Marek Fidali
Department of Fundamentals of Machinery Design, Faculty of Mechanical Engineering, Silesian University of Technology, Gliwice, Poland
1 shared publication
Latest Publications
- Open Access
- 28 December 2025
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 26 (1) , 31
Pulsed operation of a DC welding power source in resistance projection welding
The effect of pulse welding current (DC, 1 kHz) on the progression of projection welding process of nuts was analysed. The study involved a comparative analysis using identical average value for pulsed DC current with continuous direct current (DCc), which is commonly used in conventional mode. The analysis was conducted for nuts featuring four trapezoidal projections, made of grade 10B21 steel (AISI1017-SORPAS library), with a projection height of 1.2 mm and an initial contact area between the projection and the sheet metal of 7.8 mm 2 . The second welded component was a 3.0 mm thick DC04 sheet metal. Numerical analyses in both cases were conducted using the SORPAS ™ software. The characteristic parameters evaluated were weld strength, volume of melted material (in both the sheet and the projection), area of molten material in the contact region, welding energy, and average welding current. The results of the numerical calculations were verified experimentally. The study demonstrated the beneficial effect of pulsed welding current (DC, 1 kHz) on weld quality, particularly in terms of improved strength. It is possible to both reduce welding time and increase weld strength for pulsed DC welding. With comparable weld strength, welding time can be reduced by over 30%. In turn, for the same welding time (and thus the same energy), the weld strength can be increased by 35%.
- 28 December 2025
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 26 (1) , 31
Open AccessPulsed operation of a DC welding power source in resistance projection welding
The effect of pulse welding current (DC, 1 kHz) on the progression of projection welding process of nuts was analysed. The study involved a comparative analysis using identical average value for pulsed DC current with continuous direct current (DCc), which is commonly used in conventional mode. The analysis was conducted for nuts featuring four trapezoidal projections, made of grade 10B21 steel (AISI1017-SORPAS library), with a projection height of 1.2 mm and an initial contact area between the projection and the sheet metal of 7.8 mm 2 . The second welded component was a 3.0 mm thick DC04 sheet metal. Numerical analyses in both cases were conducted using the SORPAS ™ software. The characteristic parameters evaluated were weld strength, volume of melted material (in both the sheet and the projection), area of molten material in the contact region, welding energy, and average welding current. The results of the numerical calculations were verified experimentally. The study demonstrated the beneficial effect of pulsed welding current (DC, 1 kHz) on weld quality, particularly in terms of improved strength. It is possible to both reduce welding time and increase weld strength for pulsed DC welding. With comparable weld strength, welding time can be reduced by over 30%. In turn, for the same welding time (and thus the same energy), the weld strength can be increased by 35%.
- Open Access
- 2 August 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 139 (9-10) , 5095-5107
Comparative analysis of a projection welding process with AC and DC current source for susceptibility study
The paper is aimed at the analysis of the influence of the welding current source (type-AC/DC) and its connection to the electrical grid on the quality of the resistance projection welding process (nuts/bolds). The investigation is based on FEM-SORPAS analysis. The relationship between (i) weld strength, (ii) the area of the melted material in the contact area of the welded elements, i.e., projection—sheet metal, and (iii) the volume of the melted material in the welding area is described in relation to the type of the welding current (AC/DC). Selected FEM calculations were referred to experimental results. In the second step, the influence of a source type and connection method on the decrease of the welding current was determined by a circuit modelling using the FALSTAD simulation environment. The obtained results show that the voltage drop and current decrease caused by the line connections and converter structure significantly reduce the strength of the joint. For nominal parameters, i.e., welding current source (type-AC/DC), the FEM calculation results were verified experimentally. Metallographic examinations of welded joints (AC/DC) were performed and compared with the temperature distribution in the welding area for FEM.
- 2 August 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 139 (9-10) , 5095-5107
Open AccessComparative analysis of a projection welding process with AC and DC current source for susceptibility study
The paper is aimed at the analysis of the influence of the welding current source (type-AC/DC) and its connection to the electrical grid on the quality of the resistance projection welding process (nuts/bolds). The investigation is based on FEM-SORPAS analysis. The relationship between (i) weld strength, (ii) the area of the melted material in the contact area of the welded elements, i.e., projection—sheet metal, and (iii) the volume of the melted material in the welding area is described in relation to the type of the welding current (AC/DC). Selected FEM calculations were referred to experimental results. In the second step, the influence of a source type and connection method on the decrease of the welding current was determined by a circuit modelling using the FALSTAD simulation environment. The obtained results show that the voltage drop and current decrease caused by the line connections and converter structure significantly reduce the strength of the joint. For nominal parameters, i.e., welding current source (type-AC/DC), the FEM calculation results were verified experimentally. Metallographic examinations of welded joints (AC/DC) were performed and compared with the temperature distribution in the welding area for FEM.
- Open Access
- 21 March 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- p. 311
Assessment of resistance spot welding process quality using modal analysis
The resistance spot welding is one of the main methods used to join thin-walled metal parts, while a number of factors adversely affect the process and thus the quality of the connections made. This article presents the study results of the possibility of applying modal analysis in the quality examination of welded parts by detecting the missing weld. It was aimed to determine this kind welding process imperfections influence on modal shapes and frequencies by the study of the dynamic properties of welded elements in the frequency domain. The research included real and numerical tests. The proposed testing method for spot welded constructions is a scientific novelty in the world, but the investigation results indicated, that the modal analysis may find application in detecting welding defects such as the lack of the welds. To assess the quality of the numerical models, the results obtained in the simulation and experimental test results were compared. The analysis involved the first five modes. The mode shapes in relation to the first five modal frequencies identified using the FEM analyses and the experimental tests was consistent with respect to element distortion. The differences indicate the satisfactory conformity of the numerical simulation results with the experimental test results. The article fundamentally demonstrates the applicability of the above-mentioned method to analyse the performance of all welds at once.
- 21 March 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- p. 311
Open AccessAssessment of resistance spot welding process quality using modal analysis
The resistance spot welding is one of the main methods used to join thin-walled metal parts, while a number of factors adversely affect the process and thus the quality of the connections made. This article presents the study results of the possibility of applying modal analysis in the quality examination of welded parts by detecting the missing weld. It was aimed to determine this kind welding process imperfections influence on modal shapes and frequencies by the study of the dynamic properties of welded elements in the frequency domain. The research included real and numerical tests. The proposed testing method for spot welded constructions is a scientific novelty in the world, but the investigation results indicated, that the modal analysis may find application in detecting welding defects such as the lack of the welds. To assess the quality of the numerical models, the results obtained in the simulation and experimental test results were compared. The analysis involved the first five modes. The mode shapes in relation to the first five modal frequencies identified using the FEM analyses and the experimental tests was consistent with respect to element distortion. The differences indicate the satisfactory conformity of the numerical simulation results with the experimental test results. The article fundamentally demonstrates the applicability of the above-mentioned method to analyse the performance of all welds at once.
- Open Access
- 15 October 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (5-6) , 2087-2095
Analysis of projection welding in relation to the non-parallelism of electrodes
The article contains the analysis of projection welding in relation to the non-parallel location (non-parallelism) of electrodes. For a thin-walled flat element, e.g., sheet metal with two embossed projections, calculations were conducted for different angles between the upper electrode and the lower electrode. The calculation involved the use of the SORPAS 3D software. The analysis included the distribution of temperature, power density, electrode displacement, the volume of molten metal in the weld nugget, nugget diameters, and energy supplied to the weld. The article presents the comparison of results obtained for various angles between the electrodes of the welding machine. The results of numerical calculations were verified experimentally through technological welding tests and destructive tests (peeling/metallographic). The convergence of the experimental and numerical results was satisfactory. The tests involved a typical element used in the automotive industry, i.e., a nut with two embossed projections in the flat part. The article represents quite an innovative new approach to multiple-projection welding from a numerical calculation point of view. Such an approach allows the researcher to identify the phenomena taking place in the process. The article also presents a new approach to the analysis of multi-projection welding as regards the non-parallelism of electrodes. The results enabled the determination of phenomena taking place in the multi-projection welding process as well as the boundary conditions in relation to which the process became improper (unstable).
- 15 October 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (5-6) , 2087-2095
Open AccessAnalysis of projection welding in relation to the non-parallelism of electrodes
The article contains the analysis of projection welding in relation to the non-parallel location (non-parallelism) of electrodes. For a thin-walled flat element, e.g., sheet metal with two embossed projections, calculations were conducted for different angles between the upper electrode and the lower electrode. The calculation involved the use of the SORPAS 3D software. The analysis included the distribution of temperature, power density, electrode displacement, the volume of molten metal in the weld nugget, nugget diameters, and energy supplied to the weld. The article presents the comparison of results obtained for various angles between the electrodes of the welding machine. The results of numerical calculations were verified experimentally through technological welding tests and destructive tests (peeling/metallographic). The convergence of the experimental and numerical results was satisfactory. The tests involved a typical element used in the automotive industry, i.e., a nut with two embossed projections in the flat part. The article represents quite an innovative new approach to multiple-projection welding from a numerical calculation point of view. Such an approach allows the researcher to identify the phenomena taking place in the process. The article also presents a new approach to the analysis of multi-projection welding as regards the non-parallelism of electrodes. The results enabled the determination of phenomena taking place in the multi-projection welding process as well as the boundary conditions in relation to which the process became improper (unstable).
- Open Access
Development of a Quality Control System Using Modal Analysis to Evaluate a Multi-Point Projection Welding Process
The article presents the results of the development and research regarding the application of modal analysis to the evaluation of a multi-point projection welding process. The quality control system is based on the information provided by modal analysis for the entire welding station after the previously completed welding process. The research is carried out due to the lack of an effective method for assessing the course of the multi-spot projection welding process in the case of a single current circuit passing through many points at the same time. A study of the applicability of modal analysis in investigating the quality of a multipoint joint was conducted for four DIN 928 nuts welded to a steel profile. The aim of the study was to determine the influence of weld defects on the displacement of resonant frequencies. To realize the objective, the dynamic properties of the entire welding station, including the sample in the frequency domain, were investigated. In the first stage of the study, a finite element method was used to perform modal analysis and examine the form of vibrations for the individual natural frequencies of the welding fixture including the sample. Then, quality verification using the dynamic resistance method was performed, which was compared later with the modal approach. The last stage of the study was to conduct modal analysis in the frequency domain to verify the numerical studies.
Open AccessDevelopment of a Quality Control System Using Modal Analysis to Evaluate a Multi-Point Projection Welding Process
The article presents the results of the development and research regarding the application of modal analysis to the evaluation of a multi-point projection welding process. The quality control system is based on the information provided by modal analysis for the entire welding station after the previously completed welding process. The research is carried out due to the lack of an effective method for assessing the course of the multi-spot projection welding process in the case of a single current circuit passing through many points at the same time. A study of the applicability of modal analysis in investigating the quality of a multipoint joint was conducted for four DIN 928 nuts welded to a steel profile. The aim of the study was to determine the influence of weld defects on the displacement of resonant frequencies. To realize the objective, the dynamic properties of the entire welding station, including the sample in the frequency domain, were investigated. In the first stage of the study, a finite element method was used to perform modal analysis and examine the form of vibrations for the individual natural frequencies of the welding fixture including the sample. Then, quality verification using the dynamic resistance method was performed, which was compared later with the modal approach. The last stage of the study was to conduct modal analysis in the frequency domain to verify the numerical studies.
- Open Access
- 1 June 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 133 (3-4) , 1915-1927
Analysis of welding conditions at synchronous operation of resistance welding machines
The paper is devoted to analysis of power losses in a resistance welding machine including supplying system and examination of welding conditions of the welding machine current in a case of synchronous (simultaneous) operation of multiple welding machines, i.e., during the conduction of welding current. Analysis of the most important contributors of power losses generated on the current path between a power source and the welded joint is carried out. The analysis is carried out for a DC (direct current) welding machine with power electronics inverter. AC (alternating current) welding machines are also taken into account. The analysis is divided in two parts. The first one is the analysis of single welding machine operation, while in the second part, coexistence (mutual operation) of two synchronous welding machines is considered. The analysis is based on results of numerical and experimental investigations. The first one is focused on calculation of power losses in the energy path (including a Sankey type power loss distribution diagrams), and the second one is based on experimental tests carried out to determine the diameter of the weld nugget and the strength of the joints, for cases of reducing the welding current. An example of simultaneous operation of welding machines was presented and discussed. The percentage voltage drops and power losses in the entire power supply path of the resistance welder are shown. The analysis carried out is extremely important from this point quality of welded joints.
- 1 June 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 133 (3-4) , 1915-1927
Open AccessAnalysis of welding conditions at synchronous operation of resistance welding machines
The paper is devoted to analysis of power losses in a resistance welding machine including supplying system and examination of welding conditions of the welding machine current in a case of synchronous (simultaneous) operation of multiple welding machines, i.e., during the conduction of welding current. Analysis of the most important contributors of power losses generated on the current path between a power source and the welded joint is carried out. The analysis is carried out for a DC (direct current) welding machine with power electronics inverter. AC (alternating current) welding machines are also taken into account. The analysis is divided in two parts. The first one is the analysis of single welding machine operation, while in the second part, coexistence (mutual operation) of two synchronous welding machines is considered. The analysis is based on results of numerical and experimental investigations. The first one is focused on calculation of power losses in the energy path (including a Sankey type power loss distribution diagrams), and the second one is based on experimental tests carried out to determine the diameter of the weld nugget and the strength of the joints, for cases of reducing the welding current. An example of simultaneous operation of welding machines was presented and discussed. The percentage voltage drops and power losses in the entire power supply path of the resistance welder are shown. The analysis carried out is extremely important from this point quality of welded joints.
- Open Access
- 29 May 2024
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 24 (3) , 1-17
Optimised projection welding of steel Bars
The article presents tests aimed at optimising the welding of bars, made of steel AISI1005 (ø 4.2 mm), in a cruciform configuration (i.e. using the cross-wire welding process). The authors identified research gaps and carried out a detailed numerical analysis of these cases. The research-related calculations involved the use of SORPAS software. The new areas of research included (i) bars with protective zinc coatings having various thicknesses of 0 µm, 5 µm, 10 µm and 30 µm, (ii) various welding current rise times (up-slope) and (iii) single and multi-pulse welding cycles. The tests were carried out using a DC 1 kHz inverter welding machine; the results concerning welding up-slope times were compared with those obtainable using a conventional AC 50 Hz welding machine. The results of the study, in the form of a welding technology with various values of up-slope time, have been implemented in industry. The inventive idea is protected by patent no. P.229445 at the Polish Patent Office.
- 29 May 2024
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 24 (3) , 1-17
Open AccessOptimised projection welding of steel Bars
The article presents tests aimed at optimising the welding of bars, made of steel AISI1005 (ø 4.2 mm), in a cruciform configuration (i.e. using the cross-wire welding process). The authors identified research gaps and carried out a detailed numerical analysis of these cases. The research-related calculations involved the use of SORPAS software. The new areas of research included (i) bars with protective zinc coatings having various thicknesses of 0 µm, 5 µm, 10 µm and 30 µm, (ii) various welding current rise times (up-slope) and (iii) single and multi-pulse welding cycles. The tests were carried out using a DC 1 kHz inverter welding machine; the results concerning welding up-slope times were compared with those obtainable using a conventional AC 50 Hz welding machine. The results of the study, in the form of a welding technology with various values of up-slope time, have been implemented in industry. The inventive idea is protected by patent no. P.229445 at the Polish Patent Office.
- Open Access
- 7 May 2024
- Published by Springer Nature in Research Square
Analysis of Projection Welding in Relation to the Non-Parallelism of Electrodes
The article contains the analysis of projection welding in relation to the non-parallel location (non-parallelism) of electrodes. For a thin-walled flat element (sheet metal) with two embossed projections, the FEM calculations were conducted in relation to different angles between the electrodes. The calculation involved the use of the software SORPAS-3D. The analysis included the temperature distribution, power density, electrode displacement, volume of molten metal, nugget diameter and welding energy. The FEM results were verified experimentally by technological welding tests, destructive examination (peeling/metallographic). The experimental tests involved the application of a typical element e.g. nut with two embossed projections. The research results allow the obtainment of knowledge concerning phenomena occurring in the above-named process and unacceptable bevelling angle between electrodes.
- 7 May 2024
- Published by Springer Nature in Research Square
Open AccessAnalysis of Projection Welding in Relation to the Non-Parallelism of Electrodes
The article contains the analysis of projection welding in relation to the non-parallel location (non-parallelism) of electrodes. For a thin-walled flat element (sheet metal) with two embossed projections, the FEM calculations were conducted in relation to different angles between the electrodes. The calculation involved the use of the software SORPAS-3D. The analysis included the temperature distribution, power density, electrode displacement, volume of molten metal, nugget diameter and welding energy. The FEM results were verified experimentally by technological welding tests, destructive examination (peeling/metallographic). The experimental tests involved the application of a typical element e.g. nut with two embossed projections. The research results allow the obtainment of knowledge concerning phenomena occurring in the above-named process and unacceptable bevelling angle between electrodes.
- 1 May 2024
- Published by Siec Badawcza Lukasiewicz - Gornoslaski Instytut Technologiczny in Materials Science and Welding Technologies
- Vol. 68 (2/2024) , 1-9
Spectral Analysis in Assessment of Multispot Projection Welding
The article presents the possibility of an innovative use of spectral analysis to control the quality of joints welded using the multispot projection welding method. The tests discussed in the article included the analysis of welding machine and welding fixtures frequency. The analysis consisted in the impulse-based excitation of vibrations in the entire system (including the welding machine and elements subjected to welding) and the recording of the object response using an acceleration sensor. The results were afterwards subjected to spectral analysis using the Fourier transform. As a result, it was possible to identify the effect of the lack of a weld on the free vibration frequencies of the entire system. Related quality control was performed by comparing the free vibration frequency spectrum of reference elements with that of elements not containing a metallic joint between them. The acquisition and analysis of measurement data were carried out in the LabView environment. The test results confirmed the possibility of using spectral analysis to control the quality of the projection welding process.
- 1 May 2024
- Published by Siec Badawcza Lukasiewicz - Gornoslaski Instytut Technologiczny in Materials Science and Welding Technologies
- Vol. 68 (2/2024) , 1-9
Spectral Analysis in Assessment of Multispot Projection Welding
The article presents the possibility of an innovative use of spectral analysis to control the quality of joints welded using the multispot projection welding method. The tests discussed in the article included the analysis of welding machine and welding fixtures frequency. The analysis consisted in the impulse-based excitation of vibrations in the entire system (including the welding machine and elements subjected to welding) and the recording of the object response using an acceleration sensor. The results were afterwards subjected to spectral analysis using the Fourier transform. As a result, it was possible to identify the effect of the lack of a weld on the free vibration frequencies of the entire system. Related quality control was performed by comparing the free vibration frequency spectrum of reference elements with that of elements not containing a metallic joint between them. The acquisition and analysis of measurement data were carried out in the LabView environment. The test results confirmed the possibility of using spectral analysis to control the quality of the projection welding process.