OSOleksandr Seliverstov

Oleksandr Seliverstov

*This is an algorithmically generated author record based on publicly available information.

Oleksandr Seliverstov has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Оцінка можливості виявлення тріщин під час контролю ЛЮМ1-ОВ на лопатках турбін після нанесення комплексних жаростійких покриттів

    by Konstantin Balushok, Oleksandr Seliverstov, Oleksandr Prokopenko, Sergii Sakhno

    Currently, gas turbine engines (GTD) are being improved and made more powerful by increasing the temperature of the gases in front of the turbine and increasing the air compression ratio in the compressor. In the aviation industry, nickel heat-resistant alloys such as ЖС6У-ВІ, ЖС26-ВІ, ЖС32-ВІ, etc. are used to manufacture GTD blades. Despite their high properties in terms of corrosion resistance and heat resistance, the service life of GTD blades and their protection against oxidation and corrosion damage is ensured by applying coatings using various technologies both to the flowing surface of the blade blades (heat-resistant and heat-protective) and to the inner surfaces of the cooled channels (diffusion coatings). Failure of turbine blades is one of the most severe types of damage to turbine blades, so at different stages of serial production, including after applying heat-resistant coatings, LUM1-OV inspection of blades is performed to detect cracks that can form during processing and lead to their failure during engine operation. The paper evaluates the possibility of detecting cracks on GTD turbine blades with complex heat-resistant coatings GCP+SDP-2. The study was carried out on samples of working blades in the form of an experiment. First, fatigue tests of the samples were carried out on a test bench until cracks appeared. Then, a complex heat-resistant coating of GCP (CrAl gas circulation coating) + SDP-2 (heat-resistant alloy of the Ni-Cr-Al-Y system) was applied to the blade profile in stages according to the serial technology. After each coating was applied, the blades were inspected by the LUM1-OV method to determine the possibility of crack detection. The results showed that immediately after the application of the complex heat-resistant coating, cracks on the blades were not detected, because they spread only in the GCP layer and partially pass into the SDP-2 layer without reaching the surface. The results obtained can be the basis for removing the luminescent inspection operation from the technological process, immediately after applying complex heat-resistant coatings. Since this does not allow detecting cracks in the blade material and can lead to unnecessary costs for additional technological operations.

  • Open Access

    Structure and properties of samples made from XH50BMTJuB-VI (EP648-VI) alloy produced by using selective laser melting process

    by Konstantyn Balushok, Oleksandr Seliverstov, Oleksii Pedash, Nataliya Lysenko

    The paper presented examines the composition, the structure and properties of samples made from the XH50VMTJuB-VI (hereinafter EP648-VI) alloy obtained by using the selective laser melting process (the SLM-process) in relation to manufacturing parts for aviation purposes. The authors carried out a comparative study of the samples’ structure and properties upon conducting such operations as depositing in two directions (horizontal and vertical), separate heat treatment and after hot isostatic pressing (HIP) followed by a standard heat treatment process applied for deformable semi-finished products made from the XH50VMTJuB-VI(EP648-VI) alloy. The authors inform that the manufacturing of samples by means of the SLM-process involved powders obtained through the technology of the vacuum-induction spraying of the molten metal jet with an inert gas (argon). The paper has established that samples obtained by using the HIP process with the application of the heat treatment (a vacuum high-temperature homogenization followed by a long-term aging) demonstrated the best set of mechanical properties, since the implemented complex process ensured the “healing” of pores and discontinuities in the structure, and strengthening by means of the intermetallic g¢-phase, while separations of the excess, needle-shaped a -Cr phase are fine and evenly distributed in the material structure. The authors noted that mechanical properties of samples under analysis were generally in compliance with the requirements set forth in the regulatory documentation for deformable semi-finished products made from the XH50VMTJuB-VI (EP648-VI) alloy, while underlining the increase in the level of impact strength of samples that underwent the HIP process, and the long-term strength of samples manufactured in the vertical direction compared to other options studied. Following the results of the analysis, the authors established that the SLM-process made it possible to manufacture products whose level of mechanical properties was close to the level of the deformable material, and even exceeded it in some cases.