Jerzy Zajac
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jerzy Zajac has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Adrian Anghelescu
National Institute for Research and Development in Microtechnologies, 077190 Bucharest, Romania
1 shared publication - Adrian Tulbure
Faculty of Informatics and Engineering, “1 Decembrie 1918” University of Alba Iulia, Gabriel Bethlen 5, 510009 Alba Iulia, Romania
1 shared publication - Bogdan Firtat
National Institute for Research and Development in Microtechnologies, 077190 Bucharest, Romania
1 shared publication - Carmen Moldovan
National Institute for Research and Development in Microtechnologies, 077190 Bucharest, Romania
1 shared publication - Costin Brasoveanu
National Institute for Research and Development in Microtechnologies, 077190 Bucharest, Romania
1 shared publication - Dariusz Szmigiel
Sieć Badawcza Łukasiewicz-Instytut Mikroelektroniki i Fotoniki, 02-668 Warszawa, Poland
1 shared publication
Latest Publications
- Open Access
- 27 May 2024
- Published by MDPI AG in Electronics
- Vol. 13 (11) , 2087
Piezoelectric MEMS Energy Harvester for Low-Power Applications
With the global market value of sensors on the rise, this paper focuses on the fabrication and testing of a proof-of-concept piezoelectric energy harvester which is able to harvest mechanical energy from the ambient environment and convert it into electrical energy in order to power wireless sensor networks. We focused on obtaining a new device structure based on a comb-type array of piezoelectric MEMS cantilevers (2 × 10) for a resonant frequency in the environmental application domain (a few hundred Hz) and a chip area of only 1 cm2. The configuration of the lead-free piezoelectric cantilever consists of a Si substrate, a pair of Ti-Pt electrodes and a sputtered piezoelectric layer of 12% Sc-doped AlN with a thickness of 1000 nm, a dielectric constant of ~13 and e31,f = 1.3 C/m2. At a resonant frequency of 465.2 Hz and an acceleration of 1 g, the maximum value for the collected power was 2.53 µW for an optimal load resistance of 1 MΩ resulting in a power density of 60.2 nW/mm3 for the unpacked device, without taking into account the vibration volume. By increasing the excitation acceleration to 2 g RMS and using LTC3588-1 for the power circuitry we were able to obtain a stabilized output voltage of 1.8 V.
- 27 May 2024
- Published by MDPI AG in Electronics
- Vol. 13 (11) , 2087
Open AccessPiezoelectric MEMS Energy Harvester for Low-Power Applications
With the global market value of sensors on the rise, this paper focuses on the fabrication and testing of a proof-of-concept piezoelectric energy harvester which is able to harvest mechanical energy from the ambient environment and convert it into electrical energy in order to power wireless sensor networks. We focused on obtaining a new device structure based on a comb-type array of piezoelectric MEMS cantilevers (2 × 10) for a resonant frequency in the environmental application domain (a few hundred Hz) and a chip area of only 1 cm2. The configuration of the lead-free piezoelectric cantilever consists of a Si substrate, a pair of Ti-Pt electrodes and a sputtered piezoelectric layer of 12% Sc-doped AlN with a thickness of 1000 nm, a dielectric constant of ~13 and e31,f = 1.3 C/m2. At a resonant frequency of 465.2 Hz and an acceleration of 1 g, the maximum value for the collected power was 2.53 µW for an optimal load resistance of 1 MΩ resulting in a power density of 60.2 nW/mm3 for the unpacked device, without taking into account the vibration volume. By increasing the excitation acceleration to 2 g RMS and using LTC3588-1 for the power circuitry we were able to obtain a stabilized output voltage of 1.8 V.