Dariusz Czułek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dariusz Czułek has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
A Duță
National Institute of Metrology (INM), Sos. Vitan-Bârzesti 11, 042122 Bucuresti, Romania
1 shared publicationAldona Kubala-Kukuś
1 shared publication- Aldona Nowicka1 shared publication
- Alessandro Germak
INRiM, National Institute of Metrological Research, 10135 Torino, Italy
1 shared publication - Andrzej Sierakowski
Institute of Microelectronics and Photonics, Łukasiewicz Research Network
1 shared publication B Gastaldi
13 Instituto Nacional de Tecnología Industrial (INTI), Av. Vélez Sarsfield 1561, Córdoba, X5000JKC, Argentina
1 shared publication
Latest Publications
- Open Access
- 5 June 2026
- Published by Elsevier in SSRN Electronic Journal
Fabrication and Metrological Validation of a Candidate AFM Calibration Standard Based on Silicon Nanostructures
This study presents the design, fabrication, and the AFM technique characterization of novel silicon-based periodic nanostructures intended as advanced calibration references for SPM lateral and vertical scaling. The samples were fabricated using electron beam lithography (EBL) to produce sub-micrometer structures (critical dimension: 250 nm half-pitch), resulting in raised (islands) or recessed (pits) SiO2 square arrays in silicon, with controlled height (depth) of 40 nm. The resulting structures were thoroughly characterized using the AFM technique. AFM measurements were preceded by an characterization of the commercial TGQ1 calibration sample (nominal values: period of 3.0 μm, structure size 1.5 μm and height 20 nm), which confirmed proper operation of the AFM system and demonstrated reliable measurement performance. The AFM analysis of the fabricated samples facilitated determining the X and Y spectral periods as well as its height (depth). The fabricated structures are characterized by very high repeatability of the periodic patterns, both the in the X and Y directions (standard deviation of the mean on the level 0.3-0.6 nm (island structure) and 0.3-3 nm (pit structure), as well as in height/depth (0.06-0.08 nm/0.02-0.05 nm). The AFM results applied to determine structural periodicity of the fabricated samples were further confirmed by the Scanning Electron Microscopy (SEM) measurements. These custom nanostructures demonstrate excellent dimensional stability, cleanability, and compatibility with the AFM technique, addressing key limitations of commercial standards. Furthermore, they offer a promising pathway toward more versatile, SI-traceable calibration artifacts for emerging high-resolution SPM applications in nanotechnology, materials science, and nanometrology.
- 5 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessFabrication and Metrological Validation of a Candidate AFM Calibration Standard Based on Silicon Nanostructures
This study presents the design, fabrication, and the AFM technique characterization of novel silicon-based periodic nanostructures intended as advanced calibration references for SPM lateral and vertical scaling. The samples were fabricated using electron beam lithography (EBL) to produce sub-micrometer structures (critical dimension: 250 nm half-pitch), resulting in raised (islands) or recessed (pits) SiO2 square arrays in silicon, with controlled height (depth) of 40 nm. The resulting structures were thoroughly characterized using the AFM technique. AFM measurements were preceded by an characterization of the commercial TGQ1 calibration sample (nominal values: period of 3.0 μm, structure size 1.5 μm and height 20 nm), which confirmed proper operation of the AFM system and demonstrated reliable measurement performance. The AFM analysis of the fabricated samples facilitated determining the X and Y spectral periods as well as its height (depth). The fabricated structures are characterized by very high repeatability of the periodic patterns, both the in the X and Y directions (standard deviation of the mean on the level 0.3-0.6 nm (island structure) and 0.3-3 nm (pit structure), as well as in height/depth (0.06-0.08 nm/0.02-0.05 nm). The AFM results applied to determine structural periodicity of the fabricated samples were further confirmed by the Scanning Electron Microscopy (SEM) measurements. These custom nanostructures demonstrate excellent dimensional stability, cleanability, and compatibility with the AFM technique, addressing key limitations of commercial standards. Furthermore, they offer a promising pathway toward more versatile, SI-traceable calibration artifacts for emerging high-resolution SPM applications in nanotechnology, materials science, and nanometrology.
- 1 January 2024
- Published by IOP Publishing in Metrologia
- Vol. 61 (1A)
Report on EURAMET supplementary comparison on measurement of a 1 mm stage micrometer
Main text: The results of the EURAMET supplementary comparison on the calibration of a 1 mm stage micrometer are reported. 13 NMIs from 4 RMOs participated in the comparison. Originally, the comparison was planned to use a single artefact. Because it was destroyed during the duration of the comparison, it was necessary to carry out the test in two loops using a new artefact. Artefact circulation started in August 2020 and was completed in September 2022. Both artefacts were the same make and kind. The two artefacts are standard stage micrometers as used in optical microscopy on a transparent, low thermal expansion substrate. The scale length is 1 mm divided in 100 parts. The distances of all 100 scale marks from the zero mark have been measured by each participant. The results with associated uncertainties of all participating NMIs were in good agreement. All En values were smaller than 1 already from the pre-draft A state on. Therefore, no separate analysis of a largest consistent subset was necessary. With 1400 values without a single outlier, it is tempting to assume that uncertainty contributions are somehow overestimated. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database https://www.bipm.org/kcdb/. The final report has been peer-reviewed and approved for publication by the CCL, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).
- 1 January 2024
- Published by IOP Publishing in Metrologia
- Vol. 61 (1A)
Report on EURAMET supplementary comparison on measurement of a 1 mm stage micrometer
Main text: The results of the EURAMET supplementary comparison on the calibration of a 1 mm stage micrometer are reported. 13 NMIs from 4 RMOs participated in the comparison. Originally, the comparison was planned to use a single artefact. Because it was destroyed during the duration of the comparison, it was necessary to carry out the test in two loops using a new artefact. Artefact circulation started in August 2020 and was completed in September 2022. Both artefacts were the same make and kind. The two artefacts are standard stage micrometers as used in optical microscopy on a transparent, low thermal expansion substrate. The scale length is 1 mm divided in 100 parts. The distances of all 100 scale marks from the zero mark have been measured by each participant. The results with associated uncertainties of all participating NMIs were in good agreement. All En values were smaller than 1 already from the pre-draft A state on. Therefore, no separate analysis of a largest consistent subset was necessary. With 1400 values without a single outlier, it is tempting to assume that uncertainty contributions are somehow overestimated. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database https://www.bipm.org/kcdb/. The final report has been peer-reviewed and approved for publication by the CCL, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).