Sultan Ussenkhan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sultan Ussenkhan has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Almasbek U. Utegenov
Al-Farabi Kazakh National University, Almaty, Kazakhstan
5 shared publications - Sagi A. Orazbayev
Al-Farabi Kazakh National University
5 shared publications - Baglan Kyrykbay
Institute of Applied Sciences and Information Technologies
4 shared publications - Nazym Akhanova
Kazakh-British Technical University, Almaty, Kazakhstan
3 shared publications - Zhanseriк Onaibergenov
Institute of Applied Sciences and Information Technologies; Al-Farabi Kazakh National University
2 shared publications - A. R. Abdirakhmanov
University of Mons
1 shared publication
Latest Publications
- 27 June 2026
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 23 (2)
AUTOMATION OF NANOPARTICLE SYNTHESIS PROCESSES IN A PLASMA ENVIRONMENT USING LABVIEW
This work presents an automated control system for the synthesis of nanomaterials by plasma-enhanced chemical vapor deposition (PECVD), implemented using the LabVIEW software environment. The main objective of the study is to develop an integrated hardware-software platform that enables sequential control of the key stages of the PECVD process, including vacuum chamber preparation, pressure monitoring, working gas supply, plasma ignition, power matching, cyclic nanomaterial growth, and optical monitoring of nanoparticles in the plasma environment. The use of LabVIEW made it possible to integrate actuator control, experimental parameter acquisition, and realtime process visualization within a single automated system. The automated cycle begins with evacuation of the reaction chamber to a predefined base pressure. Transition to the next stage is permitted only after the specified pressure threshold has been reached, ensuring reproducible initial conditions for each experiment. The program then controls the supply of the working gas through mass flow controllers (MFCs). In this work, two gas-flow control modes were considered: analog control using a 0÷5 V voltage signal and digital communication via RS-232 interface. It was shown that the analog approach requires accurate scaling of the control voltage, since applying 5 V corresponds to full-scale opening of the controller and results in the maximum gas flow. In contrast, the RS232 interface enables the gas flow rate to be specified directly in sccm, improving the accuracy, flexibility, and convenience of gas-environment control. After pressure stabilization, LabVIEW initiates RF plasma ignition and executes the RF matching algorithm aimed at minimizing reflected power and improving the stability of the plasma process. A separate software module implements the cyclic nanomaterial growth mode, in which the plasma-on time, plasma duration, and total number of synthesis cycles are predefined. This approach makes it possible to control material accumulation on the substrate and to correlate the process parameters with the morphological characteristics of the resulting nanostructures. The final module of the system is designed for optical monitoring of the nanoparticle cloud density in dusty plasma. For this purpose, the change in the intensity of laser radiation passing through the plasma region is recorded using a photodetector and a Keithley 2401 measuring unit connected to LabVIEW via RS-232 interface. The difference between the initial and modified optical signal intensity is used as a diagnostic parameter characterizing the formation and temporal evolution of nanoparticles. The developed system demonstrates that LabVIEW can be effectively applied not only for the automation of individual instruments, but also for the implementation of a complete digital control cycle for PECVD-based nanomaterial synthesis.
- 27 June 2026
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 23 (2)
AUTOMATION OF NANOPARTICLE SYNTHESIS PROCESSES IN A PLASMA ENVIRONMENT USING LABVIEW
This work presents an automated control system for the synthesis of nanomaterials by plasma-enhanced chemical vapor deposition (PECVD), implemented using the LabVIEW software environment. The main objective of the study is to develop an integrated hardware-software platform that enables sequential control of the key stages of the PECVD process, including vacuum chamber preparation, pressure monitoring, working gas supply, plasma ignition, power matching, cyclic nanomaterial growth, and optical monitoring of nanoparticles in the plasma environment. The use of LabVIEW made it possible to integrate actuator control, experimental parameter acquisition, and realtime process visualization within a single automated system. The automated cycle begins with evacuation of the reaction chamber to a predefined base pressure. Transition to the next stage is permitted only after the specified pressure threshold has been reached, ensuring reproducible initial conditions for each experiment. The program then controls the supply of the working gas through mass flow controllers (MFCs). In this work, two gas-flow control modes were considered: analog control using a 0÷5 V voltage signal and digital communication via RS-232 interface. It was shown that the analog approach requires accurate scaling of the control voltage, since applying 5 V corresponds to full-scale opening of the controller and results in the maximum gas flow. In contrast, the RS232 interface enables the gas flow rate to be specified directly in sccm, improving the accuracy, flexibility, and convenience of gas-environment control. After pressure stabilization, LabVIEW initiates RF plasma ignition and executes the RF matching algorithm aimed at minimizing reflected power and improving the stability of the plasma process. A separate software module implements the cyclic nanomaterial growth mode, in which the plasma-on time, plasma duration, and total number of synthesis cycles are predefined. This approach makes it possible to control material accumulation on the substrate and to correlate the process parameters with the morphological characteristics of the resulting nanostructures. The final module of the system is designed for optical monitoring of the nanoparticle cloud density in dusty plasma. For this purpose, the change in the intensity of laser radiation passing through the plasma region is recorded using a photodetector and a Keithley 2401 measuring unit connected to LabVIEW via RS-232 interface. The difference between the initial and modified optical signal intensity is used as a diagnostic parameter characterizing the formation and temporal evolution of nanoparticles. The developed system demonstrates that LabVIEW can be effectively applied not only for the automation of individual instruments, but also for the implementation of a complete digital control cycle for PECVD-based nanomaterial synthesis.
- Open Access
- 8 June 2026
- Published by al-Farabi Kazakh National University in International Journal of Mathematics and Physics
- Vol. 17 (1) , 22-31
PREPARATION OF TRANSPARENT SUPERHYDROPHOBIC COATINGS WITH ANTI-ICING, ANTI-FOGGING AND SELF-CLEANING PROPERTIES BY PLASMA POLYMERISATION AT ATMOSPHERIC PRESSURE
This study analyses the stability of superhydrophobic coatings produced by plasma polymerisation at atmospheric pressure using argon (Ar) as the base gas and hexamethyldisiloxane (HMDSO) as the precursor. The evaluation was aimed at determining the strength and durability of these coatings when exposed to various environmental factors such as fogging, anti-icing and temperature fluctuations. The superhydrophobic properties of the coatings were investigated by measuring contact angles and surface roughness values. The results show that the coatings obtained by the above mentioned method have significant water repellent property and retain their superhydrophobic characteristics for a long time. The results indicate that the combination of Ar and HMDSO in plasma polymerisation at atmospheric pressure is a promising approach to create stable and durable superhydrophobic surfaces suitable for various applications. The main focus is on the stability of coatings, their ability to resist icing and fogging. The study showed that the hydrophobic properties of the coatings can be improved by optimising the process parameters, resulting in coatings with a water contact angle of more than 154±2 degrees and high transparency of up to 98.5% in the visible range. The obtained results testify to the high efficiency of the proposed method of obtaining coatings, which opens up prospects for their application in various fields where high resistance and transparency to external influences are required. Keywords: plasma polymerization, atmospheric pressure, superhydrophobic coatings.
- 8 June 2026
- Published by al-Farabi Kazakh National University in International Journal of Mathematics and Physics
- Vol. 17 (1) , 22-31
Open AccessPREPARATION OF TRANSPARENT SUPERHYDROPHOBIC COATINGS WITH ANTI-ICING, ANTI-FOGGING AND SELF-CLEANING PROPERTIES BY PLASMA POLYMERISATION AT ATMOSPHERIC PRESSURE
This study analyses the stability of superhydrophobic coatings produced by plasma polymerisation at atmospheric pressure using argon (Ar) as the base gas and hexamethyldisiloxane (HMDSO) as the precursor. The evaluation was aimed at determining the strength and durability of these coatings when exposed to various environmental factors such as fogging, anti-icing and temperature fluctuations. The superhydrophobic properties of the coatings were investigated by measuring contact angles and surface roughness values. The results show that the coatings obtained by the above mentioned method have significant water repellent property and retain their superhydrophobic characteristics for a long time. The results indicate that the combination of Ar and HMDSO in plasma polymerisation at atmospheric pressure is a promising approach to create stable and durable superhydrophobic surfaces suitable for various applications. The main focus is on the stability of coatings, their ability to resist icing and fogging. The study showed that the hydrophobic properties of the coatings can be improved by optimising the process parameters, resulting in coatings with a water contact angle of more than 154±2 degrees and high transparency of up to 98.5% in the visible range. The obtained results testify to the high efficiency of the proposed method of obtaining coatings, which opens up prospects for their application in various fields where high resistance and transparency to external influences are required. Keywords: plasma polymerization, atmospheric pressure, superhydrophobic coatings.
- Open Access
- 20 December 2025
- Published by al-Farabi Kazakh National University in Physical Sciences and Technology
- Vol. 12 (3-4) , 4-10
Plasma treatment for producing hydrophobic and hydrophilic coatings on Fabric Surfaces
This study investigates methods for forming hydrophilic and superhydrophobic surfaces using plasma jets at atmospheric pressure. The primary focus is on ensuring the waterproofing of fabrics by creating superhydrophobic coatings. The influence of plasma on the structural and chemical characteristics of the treated materials was analyzed, along with the impact of key technological parameters, including discharge power and the composition of the plasma-forming gas. In the experiments, argon (Ar) was used as the main gas flow, while hexamethyldisiloxane (HMDSO) vapor served as the precursor. The hydrophilic properties of the surface were examined after one and ten treatment cycles using plasma in an argon flow at a rate of 40 mL/s with a power of 200 W under atmospheric pressure. The experimental parameters for the formation of the superhydrophobic coating included a discharge power of 200 W, an Ar flow rate of 40 mL/s, and a gas mixture flow rate of Ar + HMDSO at 20 mL/min. After plasma treatment, the contact angle was measured to evaluate changes in surface hydrophilicity and superhydrophobicity depending on the treatment parameters.The results confirmed the effectiveness of plasma modification for controlling the hydrophobic properties of materials. Furthermore, the stability of the coatings in contact with various liquids was investigated.
- 20 December 2025
- Published by al-Farabi Kazakh National University in Physical Sciences and Technology
- Vol. 12 (3-4) , 4-10
Open AccessPlasma treatment for producing hydrophobic and hydrophilic coatings on Fabric Surfaces
This study investigates methods for forming hydrophilic and superhydrophobic surfaces using plasma jets at atmospheric pressure. The primary focus is on ensuring the waterproofing of fabrics by creating superhydrophobic coatings. The influence of plasma on the structural and chemical characteristics of the treated materials was analyzed, along with the impact of key technological parameters, including discharge power and the composition of the plasma-forming gas. In the experiments, argon (Ar) was used as the main gas flow, while hexamethyldisiloxane (HMDSO) vapor served as the precursor. The hydrophilic properties of the surface were examined after one and ten treatment cycles using plasma in an argon flow at a rate of 40 mL/s with a power of 200 W under atmospheric pressure. The experimental parameters for the formation of the superhydrophobic coating included a discharge power of 200 W, an Ar flow rate of 40 mL/s, and a gas mixture flow rate of Ar + HMDSO at 20 mL/min. After plasma treatment, the contact angle was measured to evaluate changes in surface hydrophilicity and superhydrophobicity depending on the treatment parameters.The results confirmed the effectiveness of plasma modification for controlling the hydrophobic properties of materials. Furthermore, the stability of the coatings in contact with various liquids was investigated.
- Open Access
- 1 January 2025
- Published by al-Farabi Kazakh National University in Physical Sciences and Technology
- Vol. 12 (3-4) , 4-9
Plasma treatment for producing hydrophobic and hydrophilic coatings on fabric surfaces
This study examines the formation of hydrophilic and superhydrophobic surfaces using atmospheric-pressure plasma jets, with a particular emphasis on developing durable waterproof coatings for textile materials. The effects of plasma treatment on the structural and chemical properties of the substrates were analyzed, along with the influence of key technological parameters such as discharge power and the composition of the plasma-forming gas. Argon (Ar) was used as the primary plasma gas, while hexamethyldisiloxane (HMDSO) vapor served as the precursor for hydrophobic coating formation. Surface hydrophilicity was evaluated after one and ten treatment cycles using Ar plasma at a flow rate of 40 mL/s and a discharge power of 200 W. Superhydrophobic coatings were produced under similar plasma conditions, with a gas mixture of Ar + HMDSO introduced at 20 mL/min. Contact angle measurements were performed to assess changes in wettability and to quantify the hydrophilic or superhydrophobic character of the treated surfaces. The results demonstrate that plasma treatment enables effective tuning of surface hydrophobicity and that the resulting coatings exhibit stable performance when exposed to various liquids.
- 1 January 2025
- Published by al-Farabi Kazakh National University in Physical Sciences and Technology
- Vol. 12 (3-4) , 4-9
Open AccessPlasma treatment for producing hydrophobic and hydrophilic coatings on fabric surfaces
This study examines the formation of hydrophilic and superhydrophobic surfaces using atmospheric-pressure plasma jets, with a particular emphasis on developing durable waterproof coatings for textile materials. The effects of plasma treatment on the structural and chemical properties of the substrates were analyzed, along with the influence of key technological parameters such as discharge power and the composition of the plasma-forming gas. Argon (Ar) was used as the primary plasma gas, while hexamethyldisiloxane (HMDSO) vapor served as the precursor for hydrophobic coating formation. Surface hydrophilicity was evaluated after one and ten treatment cycles using Ar plasma at a flow rate of 40 mL/s and a discharge power of 200 W. Superhydrophobic coatings were produced under similar plasma conditions, with a gas mixture of Ar + HMDSO introduced at 20 mL/min. Contact angle measurements were performed to assess changes in wettability and to quantify the hydrophilic or superhydrophobic character of the treated surfaces. The results demonstrate that plasma treatment enables effective tuning of surface hydrophobicity and that the resulting coatings exhibit stable performance when exposed to various liquids.
- Open Access
- 1 January 2024
- Published by al-Farabi Kazakh National University in International Journal of Mathematics and Physics
- Vol. 15 (1) , 77-82
Obtaining hydrophobic coatings from AR+HMDSO using radiofrequency discharge at atmospheric pressure
Hydrophobic coatings have attracted much attention due to their wide applications in various industries including electronics, textiles, and automotive. This study deals with the process of creating nanoscale coatings on a substrate achieved by plasma polymerization using plasma flow (jet) using radiofrequency discharge together with the precursor c6h18osi2 and the carrier gas Ar. In this work, we investigate the production of hydrophobic coatings using radiofrequency (RF) discharge at atmospheric pressure using a mixture of argon (Ar) and hexamethyldisiloxane (HMDSO). RF discharge is a versatile and efficient method of plasma generation that allows the deposition of thin films with defined properties. Here we investigate the influence of process parameters such as gas flow rate, discharge power, and substrate temperature on the morphology, chemistry, and hydrophobicity of the deposited coatings. The formation of these coatings was carefully studied under atmospheric pressure conditions, varying the number of cycles of experiments while maintaining optimal plasma parameters. The properties and elemental composition of the coatings were thoroughly studied using scanning electron microscopy (SEM) and energy dispersion spectroscopy (EDS). In addition, the obtained coatings were found to possess hydrophobic properties. The hydrophobicity of these coatings was evaluated by measuring the contact angle with a goniometer with respect to cycles of experiments and long-term durability. This study contributes to a better understanding of the synthesis, structure, and hydrophobic characteristics of nanoscale coatings, opening promising perspectives for various applications. The results show that the hydrophobicity of the coatings can be optimized by tuning the process parameters, resulting in coatings with water contact angles greater than 160 degrees. Additionally, the durability and stability of the hydrophobic coatings are evaluated under different environmental conditions, allowing an assessment of their potential for practical applications.
- 1 January 2024
- Published by al-Farabi Kazakh National University in International Journal of Mathematics and Physics
- Vol. 15 (1) , 77-82
Open AccessObtaining hydrophobic coatings from AR+HMDSO using radiofrequency discharge at atmospheric pressure
Hydrophobic coatings have attracted much attention due to their wide applications in various industries including electronics, textiles, and automotive. This study deals with the process of creating nanoscale coatings on a substrate achieved by plasma polymerization using plasma flow (jet) using radiofrequency discharge together with the precursor c6h18osi2 and the carrier gas Ar. In this work, we investigate the production of hydrophobic coatings using radiofrequency (RF) discharge at atmospheric pressure using a mixture of argon (Ar) and hexamethyldisiloxane (HMDSO). RF discharge is a versatile and efficient method of plasma generation that allows the deposition of thin films with defined properties. Here we investigate the influence of process parameters such as gas flow rate, discharge power, and substrate temperature on the morphology, chemistry, and hydrophobicity of the deposited coatings. The formation of these coatings was carefully studied under atmospheric pressure conditions, varying the number of cycles of experiments while maintaining optimal plasma parameters. The properties and elemental composition of the coatings were thoroughly studied using scanning electron microscopy (SEM) and energy dispersion spectroscopy (EDS). In addition, the obtained coatings were found to possess hydrophobic properties. The hydrophobicity of these coatings was evaluated by measuring the contact angle with a goniometer with respect to cycles of experiments and long-term durability. This study contributes to a better understanding of the synthesis, structure, and hydrophobic characteristics of nanoscale coatings, opening promising perspectives for various applications. The results show that the hydrophobicity of the coatings can be optimized by tuning the process parameters, resulting in coatings with water contact angles greater than 160 degrees. Additionally, the durability and stability of the hydrophobic coatings are evaluated under different environmental conditions, allowing an assessment of their potential for practical applications.