Rawiporn Promsung
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rawiporn Promsung has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Ekwipoo Kalkornsurapranee
Division of Physical Sciences, Faculty of Science, Prince of Songkla University, Hat-Yai 90110, Thailand
5 shared publications - Jobish Johns
Department of Physics, Rajarajeswari College of Engineering, Bangalore 560074, India
4 shared publications - Yeampon Nakaramontri
Sustainable Polymer & Innovative Composite Materials Research Group, Department of Chemistry, Faculty of Science, King Mongkut’s University of Technology Thonburi, Bangkok 10140, Thailand
4 shared publications - Frank Clemens
Laboratory for High Performance Ceramics, Empa, Swiss Federal Laboratories for Materials Science and Technology, Überlandstrasse 129, 8600 Dübendorf, Switzerland
3 shared publications - Adisak Keereerak
Division of Physical Sciences , Faculty of Science , Prince of Songkla University , Hatyai , Songkhla , Thailand , psu.ac.th
2 shared publications - Antonia Georgopoulou
Cyborg Robotics and Intelligent Sensing (CyRIS) Max Planck Institute for Intelligent Systems Stuttgart & Cyber Valley Germany
2 shared publications
Latest Publications
- Open Access
- 4 February 2026
- Published by Elsevier in SSRN Electronic Journal
Enhancing piezoresistive sensitivity of natural rubber composites filled with conductive carbon black: A comparative study of grafted vs ungrafted forms
This study presents the development of piezoresistive strain sensors based on natural rubber (NR) filled conductive carbon black (CCB) composites for human motion detection applications. CCB-based composites with ungrafted NR and methyl methacrylate (MMA) grafted NR matrix were compared, based on their mechanical, electrical and piezoresistive properties. The successful synthesis of grafted NR was confirmed, for both materials influence of CCB contents was systematically investigated. Incorporation of CCB significantly improved the tensile properties of the composites. Composite matrix exhibiting superior reinforcement due to enhanced filler distribution and stronger filler-matrix interactions. Electrically, the composites with grafted NR matrix exhibited lower initial resistance, more uniform conductive networks, and higher gauge factors. These results confirm the presence of a CCB network structure, which effectively reorganizes the dead-arm CCB domains during extension. Furthermore, cyclic and quasi-static tests exhibited high relative resistance change, excellent repeatability and revealed stability with signal drift for composites with grafted NR matrix. Notably, exhibited higher stress relaxation, but lower relaxation of resistance could be achieved using grafted NR matrix, suggesting an accelerated viscoelastic stress decay accompanied by more stabilized conductive pathways within the composite network. The practical utility of the developed materials was demonstrated in wearable motion detection, where the grafted NR/CCB sensor successfully tracked complex hand movements with high reproducibility. These findings highlight grafted NR matrix material as an effective strategy to simultaneously achieve reinforced mechanical properties, stabilized electrical networks, and enhanced strain-sensing performance for piezoresistive NR composites, making them promising candidates for flexible and wearable sensor applications.
- 4 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEnhancing piezoresistive sensitivity of natural rubber composites filled with conductive carbon black: A comparative study of grafted vs ungrafted forms
This study presents the development of piezoresistive strain sensors based on natural rubber (NR) filled conductive carbon black (CCB) composites for human motion detection applications. CCB-based composites with ungrafted NR and methyl methacrylate (MMA) grafted NR matrix were compared, based on their mechanical, electrical and piezoresistive properties. The successful synthesis of grafted NR was confirmed, for both materials influence of CCB contents was systematically investigated. Incorporation of CCB significantly improved the tensile properties of the composites. Composite matrix exhibiting superior reinforcement due to enhanced filler distribution and stronger filler-matrix interactions. Electrically, the composites with grafted NR matrix exhibited lower initial resistance, more uniform conductive networks, and higher gauge factors. These results confirm the presence of a CCB network structure, which effectively reorganizes the dead-arm CCB domains during extension. Furthermore, cyclic and quasi-static tests exhibited high relative resistance change, excellent repeatability and revealed stability with signal drift for composites with grafted NR matrix. Notably, exhibited higher stress relaxation, but lower relaxation of resistance could be achieved using grafted NR matrix, suggesting an accelerated viscoelastic stress decay accompanied by more stabilized conductive pathways within the composite network. The practical utility of the developed materials was demonstrated in wearable motion detection, where the grafted NR/CCB sensor successfully tracked complex hand movements with high reproducibility. These findings highlight grafted NR matrix material as an effective strategy to simultaneously achieve reinforced mechanical properties, stabilized electrical networks, and enhanced strain-sensing performance for piezoresistive NR composites, making them promising candidates for flexible and wearable sensor applications.
- Open Access
- 1 January 2026
- Published by Wiley in International Journal of Polymer Science
- Vol. 2026 (1) , 8121720
Influence of Mesostructure in Natural Rubber on Mechanical, Dynamic Mechanical, and Thermomechanical Properties of Several Hevea brasiliensis Clones
This study focused primarily on the relationship between mesostructure and the final vulcanizate performance of solid natural rubber (NR) derived from three Hevea brasiliensis clones: RRIM600, RRIT251, and PB235. The evaluated mesostructural characteristics included molecular weight (Mw), polydispersity index (PDI), molar mass distribution (MMD), and protein content. The RRIM600 and RRIT251 clones exhibited a bimodal MMD and a broad PDI, which correlated with their higher protein content. Notably, the RRIM600 clone demonstrated superior mechanical properties, including 500% modulus (5.21 MPa), tensile strength (27.19 MPa), tear strength (27.38 N mm −1 ), and rebound resilience (73.30%). It also showed enhanced thermal–mechanical stability, with a T90 of 213.5°C determined via temperature scanning stress relaxation (TSSR). Furthermore, the physical relaxation peaks in the TSSR spectrum were found to be strongly related to the protein content of the NR. Dynamic mechanical thermal analysis (DMTA) also revealed higher storage and loss modulus for RRIM600, indicating superior elasticity. Conversely, the PB235 clone displayed a unimodal MMD and the highest M w , signifying longer macromolecular chains that resulted in higher initial plasticity, minimum torque, and elongation at break. Overall, this research provides crucial insights for selecting appropriate NR clones to manufacture high‐performance rubber products.
- 1 January 2026
- Published by Wiley in International Journal of Polymer Science
- Vol. 2026 (1) , 8121720
Open AccessInfluence of Mesostructure in Natural Rubber on Mechanical, Dynamic Mechanical, and Thermomechanical Properties of Several Hevea brasiliensis Clones
This study focused primarily on the relationship between mesostructure and the final vulcanizate performance of solid natural rubber (NR) derived from three Hevea brasiliensis clones: RRIM600, RRIT251, and PB235. The evaluated mesostructural characteristics included molecular weight (Mw), polydispersity index (PDI), molar mass distribution (MMD), and protein content. The RRIM600 and RRIT251 clones exhibited a bimodal MMD and a broad PDI, which correlated with their higher protein content. Notably, the RRIM600 clone demonstrated superior mechanical properties, including 500% modulus (5.21 MPa), tensile strength (27.19 MPa), tear strength (27.38 N mm −1 ), and rebound resilience (73.30%). It also showed enhanced thermal–mechanical stability, with a T90 of 213.5°C determined via temperature scanning stress relaxation (TSSR). Furthermore, the physical relaxation peaks in the TSSR spectrum were found to be strongly related to the protein content of the NR. Dynamic mechanical thermal analysis (DMTA) also revealed higher storage and loss modulus for RRIM600, indicating superior elasticity. Conversely, the PB235 clone displayed a unimodal MMD and the highest M w , signifying longer macromolecular chains that resulted in higher initial plasticity, minimum torque, and elongation at break. Overall, this research provides crucial insights for selecting appropriate NR clones to manufacture high‐performance rubber products.
- Open Access
- 18 September 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (5) , 4310-4325
Piezoresistive Natural Rubber Composites: A Comparison Between Low‐Temperature Glutaraldehyde Curing Agents and Conventional Sulfur Curing Systems
This study examines the piezoresistive behavior of natural rubber (NR) composites cured with sulfur (S) and glutaraldehyde (GA) and reinforced with a hybrid conductive system of conductive carbon black (CCB) and carbon nanotubes (CNT). GA‐cured NR composites demonstrated superior mechano‐electrical performance, achieving a tensile modulus of 2.05 MPa at 100% strain, tensile strength of 9.6 MPa, electrical conductivity of 10.2 μS/cm, and a gauge factor of 226 at 300%–500% strain. The improvement in modulus and piezoresistive response is attributed to the homogeneous distribution of crosslink points in the GA‐cured NR network. Notably, the secondary electrical signal peak observed in S‐cured NR sensors was eliminated with GA curing. Furthermore, GA‐cured composites exhibited reduced signal drift (dynamic cycling) and relaxation (quasi‐static cycling) compared to S‐cured composites. Long‐term soft tendon actuator tests confirmed the enhanced stability of GA‐cured systems. These findings indicate that GA‐cured NR composites with hybrid CCB/CNT fillers combine high stretchability, stability, and sensitivity, making them promising candidates for high‐performance piezoresistive sensors. Leveraging renewable NR, this approach supports sustainable development while enabling applications in wearable electronics, soft robotics, and health monitoring systems.
- 18 September 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (5) , 4310-4325
Open AccessPiezoresistive Natural Rubber Composites: A Comparison Between Low‐Temperature Glutaraldehyde Curing Agents and Conventional Sulfur Curing Systems
This study examines the piezoresistive behavior of natural rubber (NR) composites cured with sulfur (S) and glutaraldehyde (GA) and reinforced with a hybrid conductive system of conductive carbon black (CCB) and carbon nanotubes (CNT). GA‐cured NR composites demonstrated superior mechano‐electrical performance, achieving a tensile modulus of 2.05 MPa at 100% strain, tensile strength of 9.6 MPa, electrical conductivity of 10.2 μS/cm, and a gauge factor of 226 at 300%–500% strain. The improvement in modulus and piezoresistive response is attributed to the homogeneous distribution of crosslink points in the GA‐cured NR network. Notably, the secondary electrical signal peak observed in S‐cured NR sensors was eliminated with GA curing. Furthermore, GA‐cured composites exhibited reduced signal drift (dynamic cycling) and relaxation (quasi‐static cycling) compared to S‐cured composites. Long‐term soft tendon actuator tests confirmed the enhanced stability of GA‐cured systems. These findings indicate that GA‐cured NR composites with hybrid CCB/CNT fillers combine high stretchability, stability, and sensitivity, making them promising candidates for high‐performance piezoresistive sensors. Leveraging renewable NR, this approach supports sustainable development while enabling applications in wearable electronics, soft robotics, and health monitoring systems.
- 19 April 2025
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 341
Carbon nanotube/conductive carbon black-filled natural rubber composites for strain sensing
- 19 April 2025
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 341
Carbon nanotube/conductive carbon black-filled natural rubber composites for strain sensing
- Open Access
- 1 January 2025
- Published by Wiley in Advances in Polymer Technology
- Vol. 2025 (1)
Impact of Molecular Weight Variation Among Rubber Clones on the Properties of Vulcanized Latex Films
Vulcanized latex films from different Hevea brasiliensis natural rubber clones, including RRIM600, RRIT251, and PB235, were prepared using the creaming process of concentrated latex. The protein content, morphology, molecular weight distribution (MWD), mechanical properties, dynamic mechanical analysis, and thermo‐mechanical properties were studied. The morphological characteristics of the Hevea brasiliensis natural rubber clones were analyzed using transmission electron microscopy (TEM). The results indicated that the particle sizes of the three clones ranged from 1.0 to 2.5 µm. Moreover, the MWD exhibited a bimodal pattern in the RRIM600 and RRIT251 clones, leading to a high polydispersity index (PDI) that correlates with protein content. Additionally, the PB235 clone showed higher molecular weight (Mw) than the other clones, which affected the properties of the vulcanized latex films. The mechanical properties, dynamic mechanical properties, thermal properties from temperature scanning stress relaxation (TSSR) analysis, and swelling resistance were also studied. The results indicated that the crosslinked density of the vulcanized latex films is related to the bimodal MWD. This leads to increased physical interactions between the end chains of short and long rubber molecules. Moreover, the crosslinked density is associated with protein content. This study confirms that the MWD and non‐rubber components in different natural rubber clones affect the properties of vulcanized rubber.
- 1 January 2025
- Published by Wiley in Advances in Polymer Technology
- Vol. 2025 (1)
Open AccessImpact of Molecular Weight Variation Among Rubber Clones on the Properties of Vulcanized Latex Films
Vulcanized latex films from different Hevea brasiliensis natural rubber clones, including RRIM600, RRIT251, and PB235, were prepared using the creaming process of concentrated latex. The protein content, morphology, molecular weight distribution (MWD), mechanical properties, dynamic mechanical analysis, and thermo‐mechanical properties were studied. The morphological characteristics of the Hevea brasiliensis natural rubber clones were analyzed using transmission electron microscopy (TEM). The results indicated that the particle sizes of the three clones ranged from 1.0 to 2.5 µm. Moreover, the MWD exhibited a bimodal pattern in the RRIM600 and RRIT251 clones, leading to a high polydispersity index (PDI) that correlates with protein content. Additionally, the PB235 clone showed higher molecular weight (Mw) than the other clones, which affected the properties of the vulcanized latex films. The mechanical properties, dynamic mechanical properties, thermal properties from temperature scanning stress relaxation (TSSR) analysis, and swelling resistance were also studied. The results indicated that the crosslinked density of the vulcanized latex films is related to the bimodal MWD. This leads to increased physical interactions between the end chains of short and long rubber molecules. Moreover, the crosslinked density is associated with protein content. This study confirms that the MWD and non‐rubber components in different natural rubber clones affect the properties of vulcanized rubber.
- Open Access
- 1 July 2024
- Published by Elsevier in Applied Materials Today
- Vol. 39
Piezoresistive properties for soft structures using hybrid CCB/CNT-based natural rubber latex composites
- 1 July 2024
- Published by Elsevier in Applied Materials Today
- Vol. 39
Open AccessPiezoresistive properties for soft structures using hybrid CCB/CNT-based natural rubber latex composites
- 1 June 2021
- Published by Elsevier in Materials Today Communications
- Vol. 27, 102387
Grafting of various acrylic monomers on to natural rubber: Effects of glutaraldehyde curing on mechanical and thermo-mechanical properties
- 1 June 2021
- Published by Elsevier in Materials Today Communications
- Vol. 27, 102387
Grafting of various acrylic monomers on to natural rubber: Effects of glutaraldehyde curing on mechanical and thermo-mechanical properties