Reece Goldsberry
Research Subjects
Research Interests
Reece Goldsberry has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Homero Castaneda
Texas A&M University
5 shared publications - Ahmad Ivan Karayan
Department of Materials Science and Engineering , Texas A&M University , College Station , Texas 77843 , United States
1 shared publication - Bilal Mansoor
Texas A&M University
1 shared publication - Brisa Martínez-Aparicio
Universidad Autónoma de Nuevo León, FIME, Centro de Investigación e Innovación en Ingeniería Aeronáutica (CIIIA), San Nicolás de los Garza 66455, Mexico
1 shared publication - Changkyu Kim
Department of Nuclear Engineering and Engineering Physics
1 shared publication - Citlalli Gaona-Tiburcio
Universidad Autónoma de Nuevo León, FIME, Centro de Investigación e Innovación en Ingeniería Aeronáutica (CIIIA), San Nicolás de los Garza 66455, Mexico
1 shared publication
Latest Publications
- Open Access
- 1 November 2026
- Published by KEAI Publishing in Journal of Pipeline Science and Engineering
Influence of Interfacial Impedance on the Potential and Current Distribution in Buried Pipelines near Coating Defects
- 1 November 2026
- Published by KEAI Publishing in Journal of Pipeline Science and Engineering
Open AccessInfluence of Interfacial Impedance on the Potential and Current Distribution in Buried Pipelines near Coating Defects
- Open Access
- 1 July 2026
- Published by KEAI Publishing in Journal of Pipeline Science and Engineering
- Vol. 6 (4)
Characterization and potential distribution mapping of cathodically protected buried pipelines based on homogeneous and heterogenous factors
- 1 July 2026
- Published by KEAI Publishing in Journal of Pipeline Science and Engineering
- Vol. 6 (4)
Open AccessCharacterization and potential distribution mapping of cathodically protected buried pipelines based on homogeneous and heterogenous factors
- Open Access
Evaluation of Passive Films on 17-7PH and 410 Stainless Steel Exposed to NaCl Solution
This work covers the formation of a passive state for two different alloys used in the aeronautical industry. The aim of this study is to investigate the effectiveness of passivation treatments on 17-7PH and 410 SS (stainless steel) samples, specifically when performed with citric and nitric acid solutions at 49 °C using an immersion time of 90 min and subsequent exposure in 3.5 wt.% NaCl solution. Employing the cyclic potentiodynamic polarization (CPP) technique, the corrosion properties of the passivated material were evaluated according to the ASTM G65-11 standard. A microstructural analysis was performed using scanning electron microscopy (SEM). The passivated layer was characterized via X-ray photoelectron spectroscopy. In the results, the CPP curves showed positive hysteresis, indicating pitting localized corrosion, and 17-7PH steel passivated at 49 °C for 90 min in citric acid exhibited lower corrosion rate values equivalent to ×10−3 mm/year.
Open AccessEvaluation of Passive Films on 17-7PH and 410 Stainless Steel Exposed to NaCl Solution
This work covers the formation of a passive state for two different alloys used in the aeronautical industry. The aim of this study is to investigate the effectiveness of passivation treatments on 17-7PH and 410 SS (stainless steel) samples, specifically when performed with citric and nitric acid solutions at 49 °C using an immersion time of 90 min and subsequent exposure in 3.5 wt.% NaCl solution. Employing the cyclic potentiodynamic polarization (CPP) technique, the corrosion properties of the passivated material were evaluated according to the ASTM G65-11 standard. A microstructural analysis was performed using scanning electron microscopy (SEM). The passivated layer was characterized via X-ray photoelectron spectroscopy. In the results, the CPP curves showed positive hysteresis, indicating pitting localized corrosion, and 17-7PH steel passivated at 49 °C for 90 min in citric acid exhibited lower corrosion rate values equivalent to ×10−3 mm/year.
- Open Access
Effect of Temperature on Passive Film Characteristics of LPBF (Laser Powder-Bed Fusion) Processing on UNS-S31603
The effect of temperature on the localized corrosion resistance and passive film characteristics of laser powder-bed fusion (LPBF) 316L (UNS S31603) was studied in a buffered 3.5 wt% NaCl solution at 25, 50, and 75 °C. DC techniques such as cyclic potentiodynamic polarization showed lower passive current densities, high breakdown potentials, and a higher resistance to initial breakdown compared with wrought 316L samples at all temperatures. However, LPBF 316L was more susceptible to metastable pitting at potentials before film breakdown and higher damage accumulation post film breakdown. AC techniques, such as Mott–Schottky analysis and electrochemical impedance spectroscopy, showed that the formed passive film was more robust on the LPBF 316L samples at all temperatures, accounting for the higher initial resistance to pitting. However, with increasing temperatures, the film formed had an increasing concentration of defect density. Passive compositions at the various test temperatures studied using X-ray photoelectron spectroscopy (XPS) showed that the LPBF samples showed higher amounts of Cr and Fe oxides and hydroxides compared with the wrought samples, which made the passive films on the LPBF samples more compact and protective. Investigation of the pits formed on the LPBF showed the preferential regions of attack were the melt-pool boundaries and cell interiors due to their being depleted of Cr and Mo when compared with the boundaries and matrix.
Open AccessEffect of Temperature on Passive Film Characteristics of LPBF (Laser Powder-Bed Fusion) Processing on UNS-S31603
The effect of temperature on the localized corrosion resistance and passive film characteristics of laser powder-bed fusion (LPBF) 316L (UNS S31603) was studied in a buffered 3.5 wt% NaCl solution at 25, 50, and 75 °C. DC techniques such as cyclic potentiodynamic polarization showed lower passive current densities, high breakdown potentials, and a higher resistance to initial breakdown compared with wrought 316L samples at all temperatures. However, LPBF 316L was more susceptible to metastable pitting at potentials before film breakdown and higher damage accumulation post film breakdown. AC techniques, such as Mott–Schottky analysis and electrochemical impedance spectroscopy, showed that the formed passive film was more robust on the LPBF 316L samples at all temperatures, accounting for the higher initial resistance to pitting. However, with increasing temperatures, the film formed had an increasing concentration of defect density. Passive compositions at the various test temperatures studied using X-ray photoelectron spectroscopy (XPS) showed that the LPBF samples showed higher amounts of Cr and Fe oxides and hydroxides compared with the wrought samples, which made the passive films on the LPBF samples more compact and protective. Investigation of the pits formed on the LPBF showed the preferential regions of attack were the melt-pool boundaries and cell interiors due to their being depleted of Cr and Mo when compared with the boundaries and matrix.
- Open Access
- 9 April 2019
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 271, 07009
Preparation and Electrochemical Characterization of Concrete Containing Microencapsulated Calcium Nitrate Corrosion Inhibitor
We present the preparation and inhibition behavior of rebar in the presence of calcium nitrate (CN)-containing microcapsules with concentrations of 0.50, 2.00, and 5.00 wt.% in concrete. From both open circuit potential (OCP) and electrochemical impedance spectroscopy spectra, it was found that an addition of microcapsules containing CN corrosion inhibitor into concrete beams successfully repassivated or maintained the passivity of the rebar when the concrete was cracked. This corrosion inhibitor repassivated the rebar by forming a passive layer on the rebar surface under the crack. This repassivation process was evident by an increase of OCP values to more positive values or by stable OCP values at around -100 mV vs SCE. An increase in phase angle after corrosion activation for the sample with 2.00 wt.% microcapsule clearly showed this repassivation process. The optimum concentration for maintaining the passivity on rebar in the cracked concrete was found to be 5.00 wt.%.
- 9 April 2019
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 271, 07009
Open AccessPreparation and Electrochemical Characterization of Concrete Containing Microencapsulated Calcium Nitrate Corrosion Inhibitor
We present the preparation and inhibition behavior of rebar in the presence of calcium nitrate (CN)-containing microcapsules with concentrations of 0.50, 2.00, and 5.00 wt.% in concrete. From both open circuit potential (OCP) and electrochemical impedance spectroscopy spectra, it was found that an addition of microcapsules containing CN corrosion inhibitor into concrete beams successfully repassivated or maintained the passivity of the rebar when the concrete was cracked. This corrosion inhibitor repassivated the rebar by forming a passive layer on the rebar surface under the crack. This repassivation process was evident by an increase of OCP values to more positive values or by stable OCP values at around -100 mV vs SCE. An increase in phase angle after corrosion activation for the sample with 2.00 wt.% microcapsule clearly showed this repassivation process. The optimum concentration for maintaining the passivity on rebar in the cracked concrete was found to be 5.00 wt.%.