SGSergey Aleksandrovich Glazkov

Sergey Aleksandrovich Glazkov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sergey Aleksandrovich Glazkov has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Methods for evaluating the mass of objects in motion by using a one-component strain-gauge dynamometer

    by S. A. Glazkov, A. R. Gorbushin, A. E. Kozik, E. A. Krapivina, A. V. Semenov, V. A. Yakyshev


  • Methods for determining the mass of objects in motion using a one-component strain-gauge dynamometer

    by S. A. Glazkov, A. R. Gorbushin, A. E. Kozik, E. A. Krapivina, A. V. Semenov, V. A. Yakyshev

    Increasing accuracy of weight-in-motion measurements is considered. Mass of moving objects is calculated through the measurement of unsteady force with the help of one-component strain-gauge dynamometers. It is shown that existing methods of dynamic weighing enable the measurement of non-stationary forces with an uncertainty exceeding 10 %. Such high error is related to the fact that, with higher speed, the accuracy of dynamic load measurements becomes more dependent on dynamical characteristics of the one-component strain-gauge dynamometer. New methods of dynamic load measurement eliminating the systematic error related to the dynamometer’s own dynamics have to be developed to increase mass determination accuracy. Two methods for weight-in-motion measurement of the mass of loads moving on the sensitive platform of a one-component strain-gauge dynamometer at high velocities are developed. Mass determination is carried out over a wide frequency range of the dynamometer, including the natural frequency. In order to apply the first method, only the dynamometer readings in the vicinity of the given point of time for calculating first and second time derivatives of the readings and the dynamical parameters of the dynamometer determined in laboratory conditions are required. To use the second method, it is necessary to first determine the natural frequency of the dynamometer with a platform, and then the frequency of the platform with the moving load. Then, measurement data obtained through methods one or two are used for calculating the mass. Average error in determining the mass using the first method was 2.8 %, and using the second method – 4.1 %. At the same time, the error did not exceed 6.0 %. The developed technology for determining the mass of moving objects can be implemented in weighing hardware for the use in many areas of industry, trade, agriculture and other.

  • Влияние границ потока при испытаниях затупленного тела на околозвуковых режимах

    by Sergey Aleksandrovich Glazkov, Aleksandr Alekseevich Ershov, Aleksandr Vladimirovich Semenov, Maksim Viktorovich Mikhailov

    Представлены результаты численного моделирования обтекания околозвуковым потоком затупленного тела при нулевом угле атаки в рабочей части с проницаемыми стенками аэродинамической (АДТ) трубы Т-128 (Россия, ЦАГИ). Расчеты выполнены с помощью пакета программ EWT-128 ЦАГИ, в котором на стенках рабочей части используется граничное условие типа Дарси. Коэффициент проницаемости в нем зависит от направления течения газа через проницаемую поверхность. Приводится сравнение расчетных и экспериментальных коэффициентов сопротивления модели, а также распределений изоэнтропического числа Маха на модели и на перфорированных стенках рабочей части АДТ. Предложен способ определения поправки к числу Маха набегающего потока для устранения влияния стенок рабочей части в аэродинамическом эксперименте (для такого типа моделей). Коэффициенты сопротивления, полученные в результате расчетов в условия АДТ, корректируются на влияние границ потока и сравниваются с данными безграничного обтекания. Расчетные поправки используются для коррекции экспериментальных данных.

  • Open Access

    Experimental study of boundary conditions on the perforated walls of test sections no. 1 and 2 of T-128 transonic wind tunnel

    by S. A. Glazkov, A. R. Gorbushin, A. V. Semenov

    This study outlines the results of experimental research on flow parameters (flow angularity and static pressure) near a perforated wall using a six-hole probe located on the wall of T-128 wind tunnel test section in the area of significant perturbation caused by the model. In test section 1 the probe was set on the upper and lower walls (during the tests of a full-scale model); in test section 2 – on the side wall (during the tests of a half model). The perforation ratio varied from f=2% to f=10%. The distance between the perforated wall and the probe varied from 70 mm to 200 mm in order to detect the position where the probe is above the boundary layer. Technique to process acquired experimental data and to determine porosity coefficient R was developed and described in detail. A particular care was taken to study perforation f=6% since it is considered as an optimality state in terms of minimizing flow boundary interference in subsonic tests. All the measurements were made during industrial tests of various models in a wide range of subsonic speeds 0.2≤М≤0.95. The introduction includes the review of works on the topic. The study provides examples of flow computation near perforated walls of wind tunnel test section for the tests of flight vehicle models using acquired boundary condition parameters.