Д. А. Ляшенко
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Д. А. Ляшенко has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Vladimir A. Perfilov
Volgograd State Technical University
2 shared publications - Artem Igorevich Bogdanov
Materials Science and Composite Materials Department, Volgograd State Technical University, 400005 Volgograd, Russia
1 shared publication - M. E. Nikolaev
Volgograd State Technical University
1 shared publication V. A. Perfilov
Volgograd State Technical University (VSTU)
1 shared publicationVladimir Perfilov
1 shared publication
Latest Publications
- 31 October 2025
- Published by Moscow State University of Civil Engineering in Vestnik MGSU
- Vol. 20 (10)
The effect of dispersed reinforcement on the macro- and microstructure of dry building mixes using activation
- 31 October 2025
- Published by Moscow State University of Civil Engineering in Vestnik MGSU
- Vol. 20 (10)
The effect of dispersed reinforcement on the macro- and microstructure of dry building mixes using activation
- Open Access
- 1 August 2024
- Published by Moscow State University of Civil Engineering in Vestnik MGSU
- Vol. 19 (7) , 1116-1124
Наномодифицированная цементная композиция
Наномодифицированная цементная композиция
- 1 August 2024
- Published by Moscow State University of Civil Engineering in Vestnik MGSU
- Vol. 19 (7) , 1116-1124
Open AccessНаномодифицированная цементная композиция
Наномодифицированная цементная композиция
- Open Access
- 1 January 2024
- Published by Tambov State Technical University in Image Journal of Advanced Materials and Technologies
- Vol. 9 (2) , 91-99
Modification of fine-grained concrete with carbon nanotubes
The article considers the possibility of using nanotechnology in the production of concrete. Special attention is paid to the method of administration of nano-sized additives, due to their low concentration in the composition of concrete, as well as their tendency to form aggregates. Experimental data on the selection of a type of plasticizing additive to obtain optimum plastic properties of a concrete mix are presented. Thus, on the basis of the experimental data, the plasticizer SP-3 was selected, which allowed to reduce the water-cement ratio from 0.48 to 0.36 without losing the plasticity of the mixture. Data on the development of the composition of nanomodified fine-grained concrete by introducing Taunit-M carbon nanotubes in the amount of 0.01–0.001 % by weight of the binder are also presented. Two methods of introducing carbon nanotubes are considered, namely the technology of ultrasonic dispersion and the use of a vortex layer apparatus. The possibility of combining the two technologies to introduce a complex additive into concrete is considered. The greatest increase in strength (up to 26 %) was achieved when nanotubes were introduced into the mix using a linear induction rotator together with the introduction of a plasticizer into the water using an ultrasonic disperser.
- 1 January 2024
- Published by Tambov State Technical University in Image Journal of Advanced Materials and Technologies
- Vol. 9 (2) , 91-99
Open AccessModification of fine-grained concrete with carbon nanotubes
The article considers the possibility of using nanotechnology in the production of concrete. Special attention is paid to the method of administration of nano-sized additives, due to their low concentration in the composition of concrete, as well as their tendency to form aggregates. Experimental data on the selection of a type of plasticizing additive to obtain optimum plastic properties of a concrete mix are presented. Thus, on the basis of the experimental data, the plasticizer SP-3 was selected, which allowed to reduce the water-cement ratio from 0.48 to 0.36 without losing the plasticity of the mixture. Data on the development of the composition of nanomodified fine-grained concrete by introducing Taunit-M carbon nanotubes in the amount of 0.01–0.001 % by weight of the binder are also presented. Two methods of introducing carbon nanotubes are considered, namely the technology of ultrasonic dispersion and the use of a vortex layer apparatus. The possibility of combining the two technologies to introduce a complex additive into concrete is considered. The greatest increase in strength (up to 26 %) was achieved when nanotubes were introduced into the mix using a linear induction rotator together with the introduction of a plasticizer into the water using an ultrasonic disperser.