Rohmad Sigit
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rohmad Sigit has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Sri Ismarwanti
Research Organization for Nuclear Energy, National Research and Innovation Agency, KST B. J. Habibie, Serpong, Tangerang Selatan, Banten, Indonesia
3 shared publications - Jan Setiawan
Research Center for Energy Materials, National Research and Innovation Agency (BRIN), South Tangerang, Indonesia
2 shared publications - Maman Kartaman Ajiriyanto
Research Center for Nuclear Material and Radioactive Waste Technology – National Research and Innovation Agency
2 shared publications A Paid
Center for Nuclear Fuel Technology, BATAN, Kawasan PUSPIPTEK Building 20, Tangerang Selatan, Banten, Indonesia
1 shared publicationA. B. Ginting
National Research and Innovation Agency, Tangerang Selatan, Banten, Indonesia
1 shared publicationA. Gogo
National Research and Innovation Agency, Tangerang Selatan, Banten, Indonesia
1 shared publication
Latest Publications
- Open Access
- 30 June 2025
- Published by Universidad Nacional Autonoma de Mexico in Journal of Applied Research and Technology
- Vol. 23 (3) , 233-239
Fuel rod design for a high burnup small modular nuclear reactor
PWR is a type of nuclear reactor that is widely used as a nuclear power plant. Even though PWR has been around for a long time, technology continues to develop. The direction of development of PWR technology is to create a more compact design with a modular system (SMR) and more efficient fuel. More efficient fuel can be obtained by increasing fuel burnup. By increasing burnup, the fuel usage period is longer, thereby increasing the economic value of the fuel and reducing the volume of radioactive waste produced from spent fuel. High burnup means the fuel will be exposed to radiation for longer. Therefore, it is necessary to calculate both thermal and mechanical aspects with the new fuel rod design, to see whether the fuel can be used until the end of the fuel cycle. Calculations wereconducted using the Femaxi version 6 code. From the calculation results, it was obtained that the dimensions of the fuel rods were capable of reaching a burnup of 60 GWd/TU. The dimensions obtained include the diameter and length of the pellets of 7.4 mm and 10 mm, the diameter and depth of the disc of 4.7 mm and 0.51 mm, and the inner and outer diameters of the cladding of 7.8 mm and 9.3 mm. The calculation results show that the temperature distribution in the fuel rods during reactor operation is still within safe limits, and pellet cladding interaction (PCI) does not occur until the end of the fuel consumption cycle.
- 30 June 2025
- Published by Universidad Nacional Autonoma de Mexico in Journal of Applied Research and Technology
- Vol. 23 (3) , 233-239
Open AccessFuel rod design for a high burnup small modular nuclear reactor
PWR is a type of nuclear reactor that is widely used as a nuclear power plant. Even though PWR has been around for a long time, technology continues to develop. The direction of development of PWR technology is to create a more compact design with a modular system (SMR) and more efficient fuel. More efficient fuel can be obtained by increasing fuel burnup. By increasing burnup, the fuel usage period is longer, thereby increasing the economic value of the fuel and reducing the volume of radioactive waste produced from spent fuel. High burnup means the fuel will be exposed to radiation for longer. Therefore, it is necessary to calculate both thermal and mechanical aspects with the new fuel rod design, to see whether the fuel can be used until the end of the fuel cycle. Calculations wereconducted using the Femaxi version 6 code. From the calculation results, it was obtained that the dimensions of the fuel rods were capable of reaching a burnup of 60 GWd/TU. The dimensions obtained include the diameter and length of the pellets of 7.4 mm and 10 mm, the diameter and depth of the disc of 4.7 mm and 0.51 mm, and the inner and outer diameters of the cladding of 7.8 mm and 9.3 mm. The calculation results show that the temperature distribution in the fuel rods during reactor operation is still within safe limits, and pellet cladding interaction (PCI) does not occur until the end of the fuel consumption cycle.
- Open Access
- 31 August 2024
- Published by Universidad Nacional Autonoma de Mexico in Journal of Applied Research and Technology
- Vol. 22 (4) , 488-493
Non-destructive test of irradiated silicide fuel plate: Visual examination and digital X-ray radiography analysis
The development of high density silicide fuels for research reactor RSG-GA Siwabessy has been carried out by increasing the fuel density. The fuel density of U3Si2/Al fuels was increased from 2.96 gU/cm3 to 4.8 gU/cm3 with potential effect on the cladding integrity and its geometric stability, so a post-irradiation examination is required. Non-destructive test using digital X-ray radiography and visual inspection are the important test in performance evaluation of irradiated fuels. This research uses U3Si2/Al fuel plate with 4.8 gU/cm3 density and 20% burnup as known as CBJJ249. Visual inspection of the fuel surface was performed in hot cell 102 and 103 using a camera through the hot cell window and dedicated manipulator intra-camera. X-ray radiography test was performed in hot cell 103 using digital x-ray radiography apparatus with parameters set at 120 kV and 1000 µA, respectively. The image analysis was later performed using image processor, which involves the process of adjusting image contrast and histogram value to provide homogeneity and dimensional data of fuel plate. Based on visual inspections and digital x-ray radiography test, no significant surface defects and sub-surface defects were found. X-ray radiographic images clearly shows a homogeneous fuel profile. Thus, it can be concluded that the U3Si2/Al fuel plate during irradiation on the RSG-GAS core has a very good performance.
- 31 August 2024
- Published by Universidad Nacional Autonoma de Mexico in Journal of Applied Research and Technology
- Vol. 22 (4) , 488-493
Open AccessNon-destructive test of irradiated silicide fuel plate: Visual examination and digital X-ray radiography analysis
The development of high density silicide fuels for research reactor RSG-GA Siwabessy has been carried out by increasing the fuel density. The fuel density of U3Si2/Al fuels was increased from 2.96 gU/cm3 to 4.8 gU/cm3 with potential effect on the cladding integrity and its geometric stability, so a post-irradiation examination is required. Non-destructive test using digital X-ray radiography and visual inspection are the important test in performance evaluation of irradiated fuels. This research uses U3Si2/Al fuel plate with 4.8 gU/cm3 density and 20% burnup as known as CBJJ249. Visual inspection of the fuel surface was performed in hot cell 102 and 103 using a camera through the hot cell window and dedicated manipulator intra-camera. X-ray radiography test was performed in hot cell 103 using digital x-ray radiography apparatus with parameters set at 120 kV and 1000 µA, respectively. The image analysis was later performed using image processor, which involves the process of adjusting image contrast and histogram value to provide homogeneity and dimensional data of fuel plate. Based on visual inspections and digital x-ray radiography test, no significant surface defects and sub-surface defects were found. X-ray radiographic images clearly shows a homogeneous fuel profile. Thus, it can be concluded that the U3Si2/Al fuel plate during irradiation on the RSG-GAS core has a very good performance.
- Open Access
- 29 October 2021
- Published by National Atomic Energy Agency of Indonesia (BATAN) in Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir
- Vol. 27 (3) , 133-142
ANALISIS KETIDAKPASTIAN PENGUKURAN KEKUATAN TARIK DAN ELONGASI SPESIMEN SS304 BERBENTUK RING
ANALISIS KETIDAKPASTIAN PENGUKURAN KEKUATAN TARIK DAN ELONGASI SPESIMEN SS304 BERBENTUK RING. Ketidakpastian adalah tolok ukur dari kehandalan suatu pengukuran. Salah satu pendekatan analisa ketidakpastian yang banyak digunakan adalah dengan menggunakan Guide to the expression of uncertainty in measurement (GUM). Langkah-langkah untuk menganalisa ketidakpastian dari suatu pengukuran telah dijelaskan secara rinci oleh pendekatan GUM. Analisa ketidakpastian dilakukan pada pengujian tarik untuk mengetahui ketertelusuran data yang diperoleh. Pengujian tarik menghasilkan data berupa kekuatan tarik dan elongasi dari material uji. Kekuatan tarik adalah besaran yang melibatkan besaran gaya dan panjang. Elongasi adalah penambahan panjang saat dilakukan penarikan. Kekuatan tarik pada sampel berbentuk ring akan dipengaruhi oleh luas penampang pada kedua belah sisi ring ketika diberikan tegangan tarik. Sehingga untuk menentukan ketidakpastian pengujian tarik akan memerlukan analisa terhadap penyumbang ketidakpastian. Makalah ini memberikan penjelasan bagaimana cara untuk menganalisa ketidakpastian pengukuran kekuatan tarik dan elongasi pada sampel berbentuk ring. Selain itu juga akan diperoleh nilai ketidakpastian pengukuran kekuatan tarik dan elongasi SS304 berbentuk ring. Dari pengujian yang dilakukan dapat diketahui bahwa kekuatan tarik ring SS304 rata-rata adalah 631,070 ± 26,976 Nmm-2 dengan ketidakpastian diperluas sebesar 50,451 Nmm-2 pada tingkat kepercayaan 95%. Selain itu pada tingkat kepercayaan yang sama diperoleh hasil elongasi ring SS304 rata-rata 18,681% ± 2,425% dengan ketidakpastian diperluas sebesar 2,867%. Keberulangan data atau repeatability menjadi penyumbang terbesar terhadap ketidakpastian pengukuran kekuatan tarik dan elongasi ring SS304. Kata kunci: Ketidakpastian, GUM, kekuatan tarik, elongasi, ring SS304.
- 29 October 2021
- Published by National Atomic Energy Agency of Indonesia (BATAN) in Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir
- Vol. 27 (3) , 133-142
Open AccessANALISIS KETIDAKPASTIAN PENGUKURAN KEKUATAN TARIK DAN ELONGASI SPESIMEN SS304 BERBENTUK RING
ANALISIS KETIDAKPASTIAN PENGUKURAN KEKUATAN TARIK DAN ELONGASI SPESIMEN SS304 BERBENTUK RING. Ketidakpastian adalah tolok ukur dari kehandalan suatu pengukuran. Salah satu pendekatan analisa ketidakpastian yang banyak digunakan adalah dengan menggunakan Guide to the expression of uncertainty in measurement (GUM). Langkah-langkah untuk menganalisa ketidakpastian dari suatu pengukuran telah dijelaskan secara rinci oleh pendekatan GUM. Analisa ketidakpastian dilakukan pada pengujian tarik untuk mengetahui ketertelusuran data yang diperoleh. Pengujian tarik menghasilkan data berupa kekuatan tarik dan elongasi dari material uji. Kekuatan tarik adalah besaran yang melibatkan besaran gaya dan panjang. Elongasi adalah penambahan panjang saat dilakukan penarikan. Kekuatan tarik pada sampel berbentuk ring akan dipengaruhi oleh luas penampang pada kedua belah sisi ring ketika diberikan tegangan tarik. Sehingga untuk menentukan ketidakpastian pengujian tarik akan memerlukan analisa terhadap penyumbang ketidakpastian. Makalah ini memberikan penjelasan bagaimana cara untuk menganalisa ketidakpastian pengukuran kekuatan tarik dan elongasi pada sampel berbentuk ring. Selain itu juga akan diperoleh nilai ketidakpastian pengukuran kekuatan tarik dan elongasi SS304 berbentuk ring. Dari pengujian yang dilakukan dapat diketahui bahwa kekuatan tarik ring SS304 rata-rata adalah 631,070 ± 26,976 Nmm-2 dengan ketidakpastian diperluas sebesar 50,451 Nmm-2 pada tingkat kepercayaan 95%. Selain itu pada tingkat kepercayaan yang sama diperoleh hasil elongasi ring SS304 rata-rata 18,681% ± 2,425% dengan ketidakpastian diperluas sebesar 2,867%. Keberulangan data atau repeatability menjadi penyumbang terbesar terhadap ketidakpastian pengukuran kekuatan tarik dan elongasi ring SS304. Kata kunci: Ketidakpastian, GUM, kekuatan tarik, elongasi, ring SS304.
- Open Access
- 1 October 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2048 (1) , 012015
Capability of Indonesian Hot cell Towards Pebble Bed Post Irradiation Examination
Post irradiation examination is one of the requirements to obtain licensing of nuclear fuel, and the purpose of this activity is to represent the performance of nuclear fuel itself. Currently, Indonesia is developing the 10 MWth high-temperature reactor type with its fuel in the form of pebble bed. Indonesia has a hot cell installation that has a function to do post-irradiated examinations. This hot cell mainly used for plate and rod type fuel. This paper wants to show this installation capability to perform the post-irradiation examinations based on its documents and current status. We also show the future possibility of performing pebble bed post-irradiation examinations. The hot cell installation in Indonesia, mainly divided into two areas. First areas are to perform the examinations in the intact form of fuel and second areas are to perform in the small specimen of fuel. For the future pebble bed examinations, Indonesian hot cell structure is possible to perform these examinations. These examinations are possible with limiting amount and stay time of fuel inside the hot cell. The current status gap with requirements for pebble bed tests such as handling tool, deconsolidation apparatus, simulation accident test apparatus also is described.
- 1 October 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2048 (1) , 012015
Open AccessCapability of Indonesian Hot cell Towards Pebble Bed Post Irradiation Examination
Post irradiation examination is one of the requirements to obtain licensing of nuclear fuel, and the purpose of this activity is to represent the performance of nuclear fuel itself. Currently, Indonesia is developing the 10 MWth high-temperature reactor type with its fuel in the form of pebble bed. Indonesia has a hot cell installation that has a function to do post-irradiated examinations. This hot cell mainly used for plate and rod type fuel. This paper wants to show this installation capability to perform the post-irradiation examinations based on its documents and current status. We also show the future possibility of performing pebble bed post-irradiation examinations. The hot cell installation in Indonesia, mainly divided into two areas. First areas are to perform the examinations in the intact form of fuel and second areas are to perform in the small specimen of fuel. For the future pebble bed examinations, Indonesian hot cell structure is possible to perform these examinations. These examinations are possible with limiting amount and stay time of fuel inside the hot cell. The current status gap with requirements for pebble bed tests such as handling tool, deconsolidation apparatus, simulation accident test apparatus also is described.