Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ewelina Barnat has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Energy-Autonomous Cooling of Open Spaces—The Impact of Thermal Comfort Temperature on the Cooperation of the Cooling System with the PV Installation

    by Ewelina Barnat, Robert Sekret, Sławomir Rabczak, Justyna Darmochwał-Podoba

    Climate change and rising temperatures in cities due to the urban heat island (UHI) effect are causing increased heat stress and driving the development of efficient, sustainable outdoor cooling systems. The aim of this article was to analyze the integration of adiabatic air cooling systems with photovoltaic (PV) installations in the context of improving thermal comfort and energy autonomy. The study was conducted on the example of a bus station in Rzeszow (Poland), considering two system variants: indirect evaporative cooling and direct evaporative cooling. To assess the impact of comfort parameters on the number of hours of system operation, energy consumption, and operating costs, four upper thermal comfort limits were considered: 22 °C, 22.9 °C, 24 °C, and 25 °C. The results indicate that increasing the upper limit of thermal comfort reduces the operating time of the system and significantly reduces the demand for cooling—for example, increasing the thermal comfort range from 22.9 °C to 24 °C reduces useful energy by 41%. Assuming a thermal comfort range of 25 °C, the direct evaporative cooling system achieves full energy autonomy and is fully powered by photovoltaics. Life cycle analysis (LCA) and life cycle cost (LCC) confirmed the environmental and economic benefits of using higher thermal comfort values. The study highlights the potential of adiabatic cooling systems, in conjunction with a local photovoltaic installation, as an adaptive solution that improves thermal comfort in urban spaces with minimal energy consumption from the grid.

  • Open Access

    Energy-Autonomous Cooling of Open Spaces—The Impact of Thermal Comfort Temperature on the Cooperation of the Cooling System with the PV Installation

    by Ewelina Barnat, Robert Sekret, Slawomir Rabczak, Justyna Darmochwał-Podoba

    Climate change and rising temperatures in cities as a result of the Urban Heat Island (UHI) are increasing heat stress and forcing the development of efficient, sustainable outdoor cooling systems. The aim of this article was to analyse the integration of adiabatic air cooling systems with photovoltaic (PV) installations in the context of improving thermal comfort and energy autonomy. The study was carried out on the example of a bus station in Rzeszów (Poland), considering two variants of systems: indirect evaporative cooling (PKW/PV-CP-KW) and direct evaporative cooling (BKW/PV-CP-KW). Four levels of the upper limit of thermal comfort (TEmax = 22°C, 22.9°C, 24°C, 25°C) were considered to assess the impact of comfort parameters on the number of hours of system operation, energy consumption and operating costs. The results indicate that raising the TEmax reduces system uptime and significantly reduces the need for cooling – for example, increasing the TEmax from 22.9°C to 24°C reduces usable energy by 41%. At TEmax = 25°C, the BKW system achieves full energy autonomy, it is fully powered by PV. A Life Cycle Analysis (LCA) and Operating Cost of Ownership (LCC) confirmed the environmental and economic benefits of using higher TEmax values. The study highlights the potential of adiabatic cooling systems, in cooperation with a local PV installation, as an adaptive solution, improving thermal comfort in urban space with minimal grid energy consumption.

  • Open Access

    Cooling of Air in Outdoor Areas of Human Habitation

    by Ewelina Barnat, Robert Sekret, Bożena Babiarz

    This paper deals with the issue of air cooling in outdoor areas of human habitation. An analysis of air parameters during the summer season was carried out to determine the thermal comfort zone for a part of the northern platform of the local station in Rzeszow (Poland). The cooling capacity required for thermal comfort was calculated using outdoor air parameters and heat gains in the vicinity of the research object. Ten potential air-cooling systems were proposed for the outdoor zones. The systems differed in terms of cooling equipment, primary energy source, cooling medium, and recipients. They were divided into three categories: compressor, adsorption, and evaporative cooling. The electricity yield of the existing photovoltaic installation at the research facility was evaluated to identify potential synergies between the cooling demand and solar energy. An analysis assessed the energy, economic, and environmental impact of each proposed option. The best option for cooling the outdoor areas was found to be an evaporative cooling system with a PV system. Solar radiation can be effectively used for cooling outdoor zones in Poland in the summer. The optimal solution for the research facility is an evaporative cooling system based on direct evaporation combined with a photovoltaic system. The subject matter covered can be used as an effective tool for the optimal selection of outdoor air-cooling systems to ensure the thermal comfort of the occupants.


  • Open Access

    Energy Efficiency in Buildings: Toward Climate Neutrality

    by Bożena Babiarz, Dorota Anna Krawczyk, Alicja Siuta-Olcha, Candida Duarte Manuel, Artur Jaworski, Ewelina Barnat, Tomasz Cholewa, Beata Sadowska, Martyna Bocian, Maciej Gnieciak, et al.

    The pursuit of climate neutrality requires global systemic actions involving the use of solutions aimed at reducing emissions. Changes must be introduced in all sectors affecting climate change, namely power engineering and district heating, construction, transport, and industry, as well as agriculture and forestry. Analyzing the structure of final energy consumption in the EU by sector, it can be stated that households account for 27% of the total energy consumption. Comprehensive actions are needed to increase the energy efficiency of buildings. The aim of this paper was to indicate aspects of improving energy efficiency in buildings and their equipment, taking into account the striving for climate neutrality. Analyzed possibilities and conditions of using various solutions of energy-efficient systems aimed at increasing energy resilience and security and preventing environmental degradation. Particular attention was paid to construction and material solutions, as well as installation solutions, which increased the accumulation and energy efficiency of the building. These activities are closely related to the conditions and dynamics of the heat exchange process in the applied solutions and are also related to the factors influencing thermal comfort and energy consumption in buildings. Due to the growing popularity of modern information technologies and artificial intelligence in energy management in recent years, this article reviews the latest research in this area. One of the directions of future research indicated by scientists is autonomous building control in real time, adapting to the momentary needs of users. The analysis of the possibilities of using modern energy efficiency solutions in buildings conducted in this work may be useful for optimizing heat and energy management models and models of society’s consumption as an element of energy transformation towards climate neutrality and counteracting the deepening of energy poverty.


  • Open Access

    Frequency-dependent pulsed direct current magnetron sputtering of titanium oxide films

    by J.-Y. Kim, E. Barnat, E. J. Rymaszewski, T.-M. Lu

    Dramatic dependence of dielectric properties on the pulsing frequency was found for titanium oxide films deposited using the pulsed dc magnetron sputtering technique at room temperature. The frequency range studied was between 50 and 250 kHz by varying the oxygen pressure. A minimum leakage current density of 0.22 μA/cm2 at 0.5 MV/cm electric-field strength for a film with dielectric constant of 26 was achieved for relative oxygen pressure P=60% [P(%)=PO2/(PO2+PAr] and frequency f=200 kHz.


  • Real time copper resistivity measurements during sputter deposition

    by E.V. Barnat, T.-M. Lu

    Electrical resistivity of thin copper films sputtered onto silicon dioxide is measured in real time. The electrical resistivity is shown to strongly depend on the film's thickness, for thicknesses below the bulk mean free path of copper (390 /spl Aring/). Furthermore, observations are made on the relaxation of the electrical resistivity after the growth (by sputtering) is terminated. Both the magnitude of change in the electrical resistivity, and the time scale of change is observed to be a function of the film's thickness.