Van-Quyet Tran
Research Subjects
Van-Quyet Tran has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Yu-Ren Wu
Department of Mechanical Engineering, National Central University, Taoyuan City, Taiwan (R.O.C.)
2 shared publications Achmad Arifin
Universitas Negeri Yogyakarta
1 shared publicationNgoc-Tuan Phan
Hung Yen University of Technology and Education
1 shared publication- Van-The Tran
Hung Yen University of Technology and Education
1 shared publication
Latest Publications
- 5 October 2025
- Published by Springer Nature
- p. 14-23
A Flexible Application for Generating of Screw Rotor Profile
- 5 October 2025
- Published by Springer Nature
- p. 14-23
A Flexible Application for Generating of Screw Rotor Profile
- 17 February 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240 (3) , 3328-3337
A novel profile considered geometry optimization for unequal rotor pair of claw-type vacuum pump
In the claw-type vacuum pumps, the rotor pair is a vital component, the rotor profiles are mainly affected by the performance of the claw-type vacuum pumps. Therefore, this study proposes a novel profile for unequal rotor pair considered geometry optimization to improve the performance of claw-type vacuum pumps. The proposed unequal rotor pair's geometric models and profile equations are established since geometry parameters of unequal rotor profile evaluated and optimized to improve the performance of claw-type vacuum pump. Moreover, the influence of geometry parameters on the working area ratio and sealing line length are presented. The numerical results indicate that the performance of claw-type vacuum pumps with novel unequal rotor profiles has improved significantly compared to the traditional rotor profile. The working area ratio of the proposed pump is higher 7.2% than that of the traditional pump. The working sealing line length of the proposed pump is shorter 31.89% than that of the traditional pump.
- 17 February 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240 (3) , 3328-3337
A novel profile considered geometry optimization for unequal rotor pair of claw-type vacuum pump
In the claw-type vacuum pumps, the rotor pair is a vital component, the rotor profiles are mainly affected by the performance of the claw-type vacuum pumps. Therefore, this study proposes a novel profile for unequal rotor pair considered geometry optimization to improve the performance of claw-type vacuum pumps. The proposed unequal rotor pair's geometric models and profile equations are established since geometry parameters of unequal rotor profile evaluated and optimized to improve the performance of claw-type vacuum pump. Moreover, the influence of geometry parameters on the working area ratio and sealing line length are presented. The numerical results indicate that the performance of claw-type vacuum pumps with novel unequal rotor profiles has improved significantly compared to the traditional rotor profile. The working area ratio of the proposed pump is higher 7.2% than that of the traditional pump. The working sealing line length of the proposed pump is shorter 31.89% than that of the traditional pump.
- 24 September 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 239 (1) , 71-84
A general mathematical model for manufacturing Roots pump rotors using conical milling cutters
The rotors are the key components in the Roots pump, and the rotor manufacture time will decide the pump price. In special cases, such as when one rotor shaft has two stages, respectively, with claw-type and Roots profiles, the traditional forming method is unsuitable for manufacturing the Roots rotor stage. Instead, more suitable manufacturing methods, such as planning or end-mill milling, can be applied. However, these two methods take time and effort. Therefore, this study proposes a general mathematical approach for Roots rotor manufacturing using the conical milling cutter as the key tool, which can reduce manufacturing time. The contact points and meshing angles between the rotor and the conical milling cutter can be calculated based on contact conditions. Then, a 3D conical milling cutter surface is obtained based on the cutter profile as a straight line, and the conical cutter is designed and considered to avoid undercutting in the rotor cutting process. The generated Roots rotor can be obtained by applying cutting simulation from the proposed mathematical model. The normal deviations of the rotor can be found by comparing the generated rotor profile to the datum rotor profile. In addition, the influence of axis errors of the conical milling cutter on the tooth profiles of the Roots pump rotor is investigated and discussed. The experimental results based on the proposed mathematical model are obtained and expressed to confirm the practicability of the proposed method.
- 24 September 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 239 (1) , 71-84
A general mathematical model for manufacturing Roots pump rotors using conical milling cutters
The rotors are the key components in the Roots pump, and the rotor manufacture time will decide the pump price. In special cases, such as when one rotor shaft has two stages, respectively, with claw-type and Roots profiles, the traditional forming method is unsuitable for manufacturing the Roots rotor stage. Instead, more suitable manufacturing methods, such as planning or end-mill milling, can be applied. However, these two methods take time and effort. Therefore, this study proposes a general mathematical approach for Roots rotor manufacturing using the conical milling cutter as the key tool, which can reduce manufacturing time. The contact points and meshing angles between the rotor and the conical milling cutter can be calculated based on contact conditions. Then, a 3D conical milling cutter surface is obtained based on the cutter profile as a straight line, and the conical cutter is designed and considered to avoid undercutting in the rotor cutting process. The generated Roots rotor can be obtained by applying cutting simulation from the proposed mathematical model. The normal deviations of the rotor can be found by comparing the generated rotor profile to the datum rotor profile. In addition, the influence of axis errors of the conical milling cutter on the tooth profiles of the Roots pump rotor is investigated and discussed. The experimental results based on the proposed mathematical model are obtained and expressed to confirm the practicability of the proposed method.