LCLihua Cai

Lihua Cai

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lihua Cai has a total of 21 co-authors. Here are the top co-authors by number of shared publications:

  • Haifeng Fang

    College of Mechanical Engineering, Jiangsu University of Science & Technology, Zhenjiang, China

    3 shared publications
  • Wangyongjia Zhong

    College of Mechanical Engineering, Jiangsu University of Science & Technology, Zhenjiang, Jiangsu, China

    2 shared publications
  • D. F. He

    Jiangsu Beier Machinery Co., Ltd, Suzhou, China

    1 shared publication
  • Dianxu Ruan

    Shazhou Professional Institute of Technology, Suzhou, Jiangsu, China

    1 shared publication
  • F. J. Chu

    College of Mechanical Engineering, Jiangsu University of Science & Technology, Zhenjiang, China

    1 shared publication
  • H. F. Fang

    College of Mechanical Engineering, Jiangsu University of Science & Technology, Zhenjiang, China

    1 shared publication

Latest Publications

  • Investigation of the Temperature Field and Winding Method Effects During the Winding Process of GF-RTP

    by L. H. Cai, F. J. Chu, S. P. Zhang, H. F. Fang, Q. B. Wu, J. Yao, D. F. He

  • Open Access

    Study on the impact of near-wall air systems' wind speed variations on the combustion characteristics in coal-fired boilers

    by Lihua Cai, Wangyongjia Zhong, Dianxu Ruan, Xiangfei Lin, Haifeng Fang

    With increasingly strict national energy policies mandating ultra-low emissions for coal-fired power plants, the issue of high-temperature corrosion caused by reductive gases and elevated furnace temperatures has become critical. This study proposes the implementation of near-wall air systems on both sides of mid-furnace burners to mitigate water-cooled wall corrosion and enhance combustion efficiency. Using numerical simulation, the effects of a near-wall air system with a wind speed of 20 m/s were analyzed across the entire furnace. Results show that this approach reduces the average near-wall temperature by 4%, while increasing O? concentration in the combustion zone by approximately 6%, thus promoting more efficient combustion. Additionally, CO? and CO concentrations decrease by about 4.5% and 5.9%, respectively, effectively reducing reductive gases and alleviating high-temperature corrosion. NOx decreased significantly by 18.7%, indicating that air classification effectively suppressed NOx, which is a sign of efficient and low-nitrogen combustion. These findings offer a practical solution for improving boiler operational safety and efficiency under ultra-low emission requirements.

  • Numerical Simulation and Analysis of CO2 Bubble Deformation in PET Continuous Extrusion Process

    by Lihua Cai, Wangyongjia Zhong, Haifeng Fang, Zheng Rong, Sipeng Zhang

    In this paper, the dynamic deformation of supercritical CO2 bubbles in the shear flow field of polyethylene terephthalate (PET) is analyzed, and the dynamic continuous extrusion process of PET microcellular foaming is numerically simulated. The extrusion process of PET supercritical CO2 homogeneous solution is simulated by the user defined function (UDF) program, and the volume of fluid (VOF) method is used to track the gas‐liquid interface. The deformation of supercritical CO2 bubbles in the PET microcellular foaming extrusion process is simulated in FLUENT software. It is found that in the continuous dynamic extrusion process, the bubble moves with the polymer at a certain angle, and there will be an area at the two ends to inhibit the shear thinning of the melt, which affects the movement pattern of the bubble. The increase in shear rate is the main factor causing the increase in the aspect ratio of the bubble. The increase of the rheological index can promote the bubble to maintain the spherical shape by affecting the shear flow field around the bubble. In addition, it is found that the effect of surface tension on bubble morphology in the shear flow field is not as large as that in the static flow field.

  • Research on the impact mechanism and parameter optimization of RTP structure layer fusion process

    by Sipeng Zhang, Haifeng Fang, Lihua Cai, Junmin Zeng

    Fiber-reinforced thermoplastic composite pipes (RTP) possess a complex multilayer structure. Apart from the melting process of the reinforced layer, the melting process between the inner and outer layers and the reinforced layer is equally crucial. Factors such as heating time, heating temperature, and pipe diameter significantly influence the degree of tight bonding between these layers. The purpose of this study is to investigate the influence mechanism of the fusion process between the three main layers of RTP and to perform parameter optimization analysis. First, Box-Behnken response surface method and finite element analysis were used to obtain the softened layer thickness under different parameters and to couple the influence mechanism of process parameters on the softened layer thickness. Then, single parameter sensitivity analysis was used to reveal the influence mechanism of each parameter change on the softened layer thickness of the pipe, and then the coupling analysis of the process parameters was carried out. The analysis results show that the softened layer thickness is most sensitive to the change of heating temperature, followed by heating time and pipe diameter. Finally, the optimal parameter combination was obtained through the expected function method, and experiments were conducted on finished pipes.


  • Design and tactile classification of flexible tactile sensor for soft gripper

    by Shuo Dong, Lihua Cai, Yangyang Wei, Jianguo She

    Tactile object recognition is very important in robot sorting and handling system. The existing researches on tactile recognition mainly focus on rigid grippers, which cannot be directly applied to soft grippers with better safety and applicability. In this paper, a tactile sensor for soft gripper is proposed. The tactile sensor consists of a carbon composite Velostat and a flexible printed circuit designed for soft gripper. The sensor is equipped with signal scanning, amplifying and processing systems. A number of performance tests were carried out on the designed tactile sensor to prove that it has good performance in sensing sensitivity, loading stability, repeatability. In addition, tactile sensors are applied to tactile classification. The two fingers of the flexible gripper were loaded with a sensor and nine different objects were contacted. The tactile information of the objects was obtained through the stable gripper, and the tactile data was trained and classified by the support vector machine. Finally, the tactile recognition accuracy of the double-exponent data was 91.1%.