Mehmet Baris Daryal
Research Subjects
Mehmet Baris Daryal has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Turan
Materials Science and Nanotechnology Engineering Department, Faculty of Engineering, Yeditepe University, Ataşehir, Istanbul 34755, Turkey
1 shared publication - Mehmet Hakan Morcali
Department of Chemistry and Chemical Processing Technologies, N. Topçuoğlu Vocational School Gaziantep University, Gaziantep, Turkey
1 shared publication - Sabahattin Deniz
Marmara Üniversitesi
1 shared publication - Timurhan Eser1 shared publication
- Umay Cinarli Yavas
Materials Science and Nanotechnology Engineering Department, Faculty of Engineering, Yeditepe University, Ataşehir, Istanbul 34755, Turkey
1 shared publication - Yalçın Boztoprak
Technology Faculty, Metallurgy and Materials Engineering, Marmara University 2 , İstanbul 34854
1 shared publication
Latest Publications
- Open Access
- 25 September 2025
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 60 (3) , e266
Gold extraction from oxide gold ores through glycine leaching
The use of glycine, a non-toxic and simple amino acid, has gained attention for gold extraction because of its selective dissolution of precious metals. This study explores gold extraction from oxide gold ore using non-analytical grade glycine at concentrations of 1-3 M and reaction times ranging from 4 to 60 hours. The pH was maintained at 11-12, with the reactor temperature set at 60 °C, a stirring speed of 350 rpm, and an air flow rate of 1 L·min-1. The ore's particle size averaged 70.7 μm. The highest gold extraction (81.41%) occurred at 3 M glycine after 48 hours. Silver extraction was moderate, reaching 44.50%, while iron solubility was low at 7.71%. The results show that increased reaction time and glycine concentration enhance gold dissolution from oxide ore. This glycine-based process offers a more environmentally friendly and sustainable approach for selective extraction of gold and silver from oxide ores or oxidized waste containing precious metals.
- 25 September 2025
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 60 (3) , e266
Open AccessGold extraction from oxide gold ores through glycine leaching
The use of glycine, a non-toxic and simple amino acid, has gained attention for gold extraction because of its selective dissolution of precious metals. This study explores gold extraction from oxide gold ore using non-analytical grade glycine at concentrations of 1-3 M and reaction times ranging from 4 to 60 hours. The pH was maintained at 11-12, with the reactor temperature set at 60 °C, a stirring speed of 350 rpm, and an air flow rate of 1 L·min-1. The ore's particle size averaged 70.7 μm. The highest gold extraction (81.41%) occurred at 3 M glycine after 48 hours. Silver extraction was moderate, reaching 44.50%, while iron solubility was low at 7.71%. The results show that increased reaction time and glycine concentration enhance gold dissolution from oxide ore. This glycine-based process offers a more environmentally friendly and sustainable approach for selective extraction of gold and silver from oxide ores or oxidized waste containing precious metals.
- 1 November 2024
- Published by Faculty of Technical Sciences
REINFORCEMENT OF 3D PRINTED PLA WITH CARBON FIBER REINFORCED COMPOSITE AND INVESTIGATION OF MECHANICAL PROPERTIES
While production methods with 3D printing are developing day by day, studies on this method are also increasing. 3D layered manufacturing is a method of creating layer-by-layer 3D solid models designed with computer-aided drawing (CAD) programs using melted raw material for each layer. In addition to PLA being the most commonly used filament in 3D printing, filaments such as ABS, PETG, and TPU are also used. A wide variety of products can be produced with this production method depending on the design. The mechanical properties of the products resulting from 3D printing depend on many parameters such as the number of layers, fill rate, material used, and printing speed. Various methods are also applied to further strengthen the products produced from printing. In this study, PLA samples obtained from 3D printing were reinforced with carbon fibre reinforced polymer composite (CFRP). The reinforcement process was carried out by placing CFRP material during PLA sample production, and the mechanical properties of the resulting samples were examined. Increased hardness as well as improved tensile, bending, impact, and wear strengths of the CFRP reinforced samples were observed
- 1 November 2024
- Published by Faculty of Technical Sciences
REINFORCEMENT OF 3D PRINTED PLA WITH CARBON FIBER REINFORCED COMPOSITE AND INVESTIGATION OF MECHANICAL PROPERTIES
While production methods with 3D printing are developing day by day, studies on this method are also increasing. 3D layered manufacturing is a method of creating layer-by-layer 3D solid models designed with computer-aided drawing (CAD) programs using melted raw material for each layer. In addition to PLA being the most commonly used filament in 3D printing, filaments such as ABS, PETG, and TPU are also used. A wide variety of products can be produced with this production method depending on the design. The mechanical properties of the products resulting from 3D printing depend on many parameters such as the number of layers, fill rate, material used, and printing speed. Various methods are also applied to further strengthen the products produced from printing. In this study, PLA samples obtained from 3D printing were reinforced with carbon fibre reinforced polymer composite (CFRP). The reinforcement process was carried out by placing CFRP material during PLA sample production, and the mechanical properties of the resulting samples were examined. Increased hardness as well as improved tensile, bending, impact, and wear strengths of the CFRP reinforced samples were observed