Vivien Nemes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Vivien Nemes has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Brigitta Fruzsina Szívós
Department of Vehicle Production and Engineering, Széchenyi István University, H-9026 Győr, Hungary
10 shared publications - Szabolcs Fischer
Central Campus Győr, Széchenyi István University, H-9026 Győr, Hungary
7 shared publications - Szabolcs Szalai
Department of Vehicle Production and Engineering, Széchenyi István University, Egyetem tér 1, 9026 Győr, Hungary
7 shared publications - Dmytro Kurhan
Department of Transport Infrastructure, Ukrainian State University of Science and Technologies, UA-49010 Dnipro, Ukraine
4 shared publications - Mykola Sysyn
Institute of Railway Systems and Public Transport, Technical University Dresden, 01069 Dresden, Germany
4 shared publications - György Szabó
Central Campus Győr, Széchenyi István University, H-9026 Győr, Hungary
2 shared publications
Latest Publications
- Open Access
- 19 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 40
Mechanical Performance of Heat-Set Threaded Inserts in FDM-Printed PLA Components
Heat-set threaded inserts provide a practical solution for reusable, load-bearing joints in FDM-printed polymer parts; however, their pull-out performance is governed not only by the insert itself, but also by the surrounding printed architecture. This study examines the pull-out behavior of heat-set M3 inserts embedded in FDM-printed PLA specimens across three wall thicknesses (1.28 mm, 1.6 mm, and 1.92 mm) and three infill patterns (adaptive cubic, cross-zag, and gyroid) using a repeatable drill-stand-based insertion fixture and a two-stage embedding protocol at 190 °C. Across 27 specimens, mean peak pull-out force ranged from 1353.6 ± 7.5 N to 1551.5 ± 20.4 N. Two-way ANOVA showed that both wall thickness and infill pattern significantly affected peak force, although the wall-thickness effect was practically modest—a 20% increase in material yielded only a 4.6% increase in mean force. Cross-zag specimens failed at significantly lower loads than adaptive cubic and gyroid, which performed comparably. Two specimens (7.4%) failed prematurely because of defective insert threads rather than the printed structure, underlining the importance of fastener quality control.
- 19 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 40
Open AccessMechanical Performance of Heat-Set Threaded Inserts in FDM-Printed PLA Components
Heat-set threaded inserts provide a practical solution for reusable, load-bearing joints in FDM-printed polymer parts; however, their pull-out performance is governed not only by the insert itself, but also by the surrounding printed architecture. This study examines the pull-out behavior of heat-set M3 inserts embedded in FDM-printed PLA specimens across three wall thicknesses (1.28 mm, 1.6 mm, and 1.92 mm) and three infill patterns (adaptive cubic, cross-zag, and gyroid) using a repeatable drill-stand-based insertion fixture and a two-stage embedding protocol at 190 °C. Across 27 specimens, mean peak pull-out force ranged from 1353.6 ± 7.5 N to 1551.5 ± 20.4 N. Two-way ANOVA showed that both wall thickness and infill pattern significantly affected peak force, although the wall-thickness effect was practically modest—a 20% increase in material yielded only a 4.6% increase in mean force. Cross-zag specimens failed at significantly lower loads than adaptive cubic and gyroid, which performed comparably. Two specimens (7.4%) failed prematurely because of defective insert threads rather than the printed structure, underlining the importance of fastener quality control.
- Open Access
- 19 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 33
Deformation Analysis of Bending Tests Using the GOM TRITOP System
This paper investigates the applicability of the GOM TRITOP photogrammetric system for displacement measurement in three-point bending tests of fused deposition modeling (FDM)-printed polylactic acid (PLA) specimens. Although TRITOP was originally developed primarily for the high-precision measurement of static object states, this study explores its extension toward deformation analysis by comparing discrete measurement stages recorded before loading and after fracture. In this sense, the method does not provide continuous deformation monitoring as in conventional digital image correlation (DIC)-based approaches, but enables marker-based displacement evaluation between defined loading states. Nine specimens manufactured from different commercial filaments and infill configurations were tested, and the TRITOP results were validated against digital dial-gauge measurements. The relative differences ranged from −1.3% to +2.3%, indicating good agreement. The system also enabled the simultaneous tracking of punch and specimen-end displacements, revealing differences between printing configurations and selected asymmetric bending responses. The results suggest that TRITOP can be practically extended to stage-based displacement analysis of additively manufactured components.
- 19 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 33
Open AccessDeformation Analysis of Bending Tests Using the GOM TRITOP System
This paper investigates the applicability of the GOM TRITOP photogrammetric system for displacement measurement in three-point bending tests of fused deposition modeling (FDM)-printed polylactic acid (PLA) specimens. Although TRITOP was originally developed primarily for the high-precision measurement of static object states, this study explores its extension toward deformation analysis by comparing discrete measurement stages recorded before loading and after fracture. In this sense, the method does not provide continuous deformation monitoring as in conventional digital image correlation (DIC)-based approaches, but enables marker-based displacement evaluation between defined loading states. Nine specimens manufactured from different commercial filaments and infill configurations were tested, and the TRITOP results were validated against digital dial-gauge measurements. The relative differences ranged from −1.3% to +2.3%, indicating good agreement. The system also enabled the simultaneous tracking of punch and specimen-end displacements, revealing differences between printing configurations and selected asymmetric bending responses. The results suggest that TRITOP can be practically extended to stage-based displacement analysis of additively manufactured components.
- Open Access
- 16 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 25
Evaluation of Dimensional Precision and Repeatability in MSLA Resin Printing
The dimensional precision and repeatability of an entry-level masked stereolithography (MSLA) printer were evaluated using a two-part fit gauge representative of a blanking tool, in which the peg-bore clearance served as the functionally critical dimension. Specimens were produced on an Elegoo Mars 5 Ultra (ELEGOO, Hongkong, China) using Elegoo Standard Resin (ELEGOO, Hongkong, China), with a fixed print configuration based on the manufacturer’s recommended settings. Two single-parameter post-processing series were examined by varying either the washing time or the post-cure time. At the same time, dimensional inspection was performed using a coordinate measuring machine (CMM) and, for one series, hand-held calipers. The fit-defining diameters were reproduced accurately and remained stable across all tested conditions, yielding a consistent diametric clearance. In contrast, the axial depths of recessed features were systematically undersized and were influenced more by print configuration than by post-processing duration. The results indicate that in-plane dimensions can be reproduced reliably, whereas Z-direction features require feature-specific compensation.
- 16 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 25
Open AccessEvaluation of Dimensional Precision and Repeatability in MSLA Resin Printing
The dimensional precision and repeatability of an entry-level masked stereolithography (MSLA) printer were evaluated using a two-part fit gauge representative of a blanking tool, in which the peg-bore clearance served as the functionally critical dimension. Specimens were produced on an Elegoo Mars 5 Ultra (ELEGOO, Hongkong, China) using Elegoo Standard Resin (ELEGOO, Hongkong, China), with a fixed print configuration based on the manufacturer’s recommended settings. Two single-parameter post-processing series were examined by varying either the washing time or the post-cure time. At the same time, dimensional inspection was performed using a coordinate measuring machine (CMM) and, for one series, hand-held calipers. The fit-defining diameters were reproduced accurately and remained stable across all tested conditions, yielding a consistent diametric clearance. In contrast, the axial depths of recessed features were systematically undersized and were influenced more by print configuration than by post-processing duration. The results indicate that in-plane dimensions can be reproduced reliably, whereas Z-direction features require feature-specific compensation.
- Open Access
- 5 January 2026
- Published by Scientific Oasis in Spectrum of Engineering and Management Sciences
- Vol. 4 (1) , 233-254
Optimization of Speckle Pattern Generation for DIC-based Mechanical Characterization of Automotive Synthetic Leathers
Digital Image Correlation (DIC) is a pivotal non-contact technique for full-field deformation analysis in automotive engineering. However, the high flexibility and porosity of synthetic leathers often compromise speckle pattern stability and measurement accuracy. This study presents a systematic evaluation of commercial spray paints to optimize speckle pattern generation for automotive PVC and felt-based leathers. The methodology integrates standardized adhesion testing (ISO 2409 cross-cut test), drying-time optimization, and microscopic characterization to ensure robust bonding. Performance was validated through Erichsen cupping tests, simulating multi-axial strain states typical of automotive interior components. Results demonstrate that solvent-based acrylic sprays provide superior adhesion (ISO Class 0) and maintain pattern integrity under large deformations (up to 30% strain), whereas water-based alternatives suffer from cracking and delamination. The optimized painting protocol significantly reduces correlation errors and "lost subsets" in DIC software. This research provides a reliable experimental foundation for material characterization and Finite Element Method (FEM) validation of interior systems. The findings offer a practical, cost-effective framework for enhancing optical strain measurement precision in the automotive manufacturing and testing sectors.
- 5 January 2026
- Published by Scientific Oasis in Spectrum of Engineering and Management Sciences
- Vol. 4 (1) , 233-254
Open AccessOptimization of Speckle Pattern Generation for DIC-based Mechanical Characterization of Automotive Synthetic Leathers
Digital Image Correlation (DIC) is a pivotal non-contact technique for full-field deformation analysis in automotive engineering. However, the high flexibility and porosity of synthetic leathers often compromise speckle pattern stability and measurement accuracy. This study presents a systematic evaluation of commercial spray paints to optimize speckle pattern generation for automotive PVC and felt-based leathers. The methodology integrates standardized adhesion testing (ISO 2409 cross-cut test), drying-time optimization, and microscopic characterization to ensure robust bonding. Performance was validated through Erichsen cupping tests, simulating multi-axial strain states typical of automotive interior components. Results demonstrate that solvent-based acrylic sprays provide superior adhesion (ISO Class 0) and maintain pattern integrity under large deformations (up to 30% strain), whereas water-based alternatives suffer from cracking and delamination. The optimized painting protocol significantly reduces correlation errors and "lost subsets" in DIC software. This research provides a reliable experimental foundation for material characterization and Finite Element Method (FEM) validation of interior systems. The findings offer a practical, cost-effective framework for enhancing optical strain measurement precision in the automotive manufacturing and testing sectors.
- Open Access
- 7 November 2025
- Published by MDPI AG in Engineering Proceedings
- Vol. 113 (1) , 35
Measurement Errors and Challenges in Sheet Metal Components When Using Digital Image Correlation (DIC) Systems
Digital Image Correlation systems are increasingly being used for non-contact measurement of deformation and strain in sheet metal components. However, the accuracy of such measurements can be significantly affected by various external and system-related factors. If these are not properly considered, substantial errors may be introduced. In this study, a short and longer flat sheet specimen were clamped in a vise to investigate how overhang and clamping stability influence the accuracy of the measured deformation fields. Two different measurement volumes were also evaluated to assess their effect on the results. These factors were evaluated through targeted experiments, and the resulting data were analyzed and interpreted. Based on the findings, recommendations were formulated to enhance the reliability of Digital Image Correlation measurements in both laboratory and industrial environments.
- 7 November 2025
- Published by MDPI AG in Engineering Proceedings
- Vol. 113 (1) , 35
Open AccessMeasurement Errors and Challenges in Sheet Metal Components When Using Digital Image Correlation (DIC) Systems
Digital Image Correlation systems are increasingly being used for non-contact measurement of deformation and strain in sheet metal components. However, the accuracy of such measurements can be significantly affected by various external and system-related factors. If these are not properly considered, substantial errors may be introduced. In this study, a short and longer flat sheet specimen were clamped in a vise to investigate how overhang and clamping stability influence the accuracy of the measured deformation fields. Two different measurement volumes were also evaluated to assess their effect on the results. These factors were evaluated through targeted experiments, and the resulting data were analyzed and interpreted. Based on the findings, recommendations were formulated to enhance the reliability of Digital Image Correlation measurements in both laboratory and industrial environments.
- Open Access
- 7 August 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (15) , 8747
Investigation of the Load-Bearing Capacity of Resin-Printed Components Under Different Printing Strategies
This study examines the influence of different printing orientations and infill settings on the strength and flexibility of components produced using resin-based 3D printing, particularly with masked stereolithography (MSLA). Using a common photopolymer resin and a widely available desktop MSLA printer, we produced and tested a series of samples with varying tilt angles and internal structures. To understand their mechanical behavior, we applied a custom bending test combined with high-precision deformation tracking through the GOM ARAMIS digital image correlation system. The results obtained clearly show that both the angle of printing and the density of the internal infill structure play a significant role in how much strain the printed parts can handle before breaking. Notably, a 75° orientation provided the best deformation performance, and infill rates between 60% and 90% offered a good balance between strength and material efficiency. These findings highlight how adjusting print settings can lead to stronger parts while also saving time and resources—an important consideration for practical applications in engineering, design, and manufacturing.
- 7 August 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (15) , 8747
Open AccessInvestigation of the Load-Bearing Capacity of Resin-Printed Components Under Different Printing Strategies
This study examines the influence of different printing orientations and infill settings on the strength and flexibility of components produced using resin-based 3D printing, particularly with masked stereolithography (MSLA). Using a common photopolymer resin and a widely available desktop MSLA printer, we produced and tested a series of samples with varying tilt angles and internal structures. To understand their mechanical behavior, we applied a custom bending test combined with high-precision deformation tracking through the GOM ARAMIS digital image correlation system. The results obtained clearly show that both the angle of printing and the density of the internal infill structure play a significant role in how much strain the printed parts can handle before breaking. Notably, a 75° orientation provided the best deformation performance, and infill rates between 60% and 90% offered a good balance between strength and material efficiency. These findings highlight how adjusting print settings can lead to stronger parts while also saving time and resources—an important consideration for practical applications in engineering, design, and manufacturing.
- Open Access
Deformation Characterization of Glass Fiber and Carbon Fiber-Reinforced 3D Printing Filaments Using Digital Image Correlation
The paper offers an in-depth deformation study of glass fiber-reinforced and carbon composite filaments of 3D printers. During the certification, the authors used DIC (Digital Image Correlation) as a full-field strain measurement technique to explore key material traits as a non-contact optical measurement method. The insights captured through the DIC technology enabled to better understand the localized strain distributions during the loading of these reinforced filaments. The paper analyzes the glass fiber and carbon fiber filaments used in 3D printing that are reinforced with these materials and are subjected to bending and compressive loading. The segment presents how loading affects the performance of reinforced filaments when varying such factors as the deposition patterns, layer orientation, and other process parameters. Different types and combinations of reinforcements and printing variables were tested, and the resulting dependencies of mechanical parameters and failure modes were established for each case. Key conclusions demonstrate that the mechanical behavior of both carbon- and glass fiber-reinforced filaments is strongly affected by the 3D printing parameters, particularly infill density, pattern, and build orientation. The application of Digital Image Correlation (DIC) allowed for a precise, full-field analysis of strain distribution and deformation behavior, offering new insights into the structural performance of fiber-reinforced 3D printed composites. The findings from the study provide guidance for the proper choice of filling material and the optimal parameters for the 3D printing process of models with high-performance indexes and seamless applications in the automotive and industrial manufacturing sectors.
Open AccessDeformation Characterization of Glass Fiber and Carbon Fiber-Reinforced 3D Printing Filaments Using Digital Image Correlation
The paper offers an in-depth deformation study of glass fiber-reinforced and carbon composite filaments of 3D printers. During the certification, the authors used DIC (Digital Image Correlation) as a full-field strain measurement technique to explore key material traits as a non-contact optical measurement method. The insights captured through the DIC technology enabled to better understand the localized strain distributions during the loading of these reinforced filaments. The paper analyzes the glass fiber and carbon fiber filaments used in 3D printing that are reinforced with these materials and are subjected to bending and compressive loading. The segment presents how loading affects the performance of reinforced filaments when varying such factors as the deposition patterns, layer orientation, and other process parameters. Different types and combinations of reinforcements and printing variables were tested, and the resulting dependencies of mechanical parameters and failure modes were established for each case. Key conclusions demonstrate that the mechanical behavior of both carbon- and glass fiber-reinforced filaments is strongly affected by the 3D printing parameters, particularly infill density, pattern, and build orientation. The application of Digital Image Correlation (DIC) allowed for a precise, full-field analysis of strain distribution and deformation behavior, offering new insights into the structural performance of fiber-reinforced 3D printed composites. The findings from the study provide guidance for the proper choice of filling material and the optimal parameters for the 3D printing process of models with high-performance indexes and seamless applications in the automotive and industrial manufacturing sectors.
- Open Access
- 15 January 2025
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 9 (1) , 25
Investigation of Digital Light Processing-Based 3D Printing for Optimized Tooling in Automotive and Electronics Sheet Metal Forming
This study addresses the emerging need for efficient and cost-effective solutions in low-volume production by exploring the mechanical performance and industrial feasibility of cutting tools that are fabricated using stereolithography apparatus (SLA) technology. SLA’s high-resolution capabilities make it suitable for creating precise cutting dies, which were tested on aluminum sheets (Al99.5, 0.3 mm, and AlMg3, 1.0 mm) under a 60-ton hydraulic press. Measurements using digital image correlation (DIC) revealed minimal wear and deformation, with tolerances consistently within IT 0.1 mm. The results demonstrated that SLA-printed tools perform comparably to conventional metal tools in cutting and bending operations, achieving similar surface quality and edge precision while significantly reducing the production time and cost. Despite some limitations in wear resistance, the findings highlight SLA technology’s potential for rapid prototyping and short-run manufacturing in the automotive and electronics sectors. This research fills a critical gap in understanding SLA-based tooling applications, offering insights into process optimization to enhance tool durability and broaden material compatibility. These advancements position SLA technology as a transformative tool-making technology for flexible manufacturing.
- 15 January 2025
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 9 (1) , 25
Open AccessInvestigation of Digital Light Processing-Based 3D Printing for Optimized Tooling in Automotive and Electronics Sheet Metal Forming
This study addresses the emerging need for efficient and cost-effective solutions in low-volume production by exploring the mechanical performance and industrial feasibility of cutting tools that are fabricated using stereolithography apparatus (SLA) technology. SLA’s high-resolution capabilities make it suitable for creating precise cutting dies, which were tested on aluminum sheets (Al99.5, 0.3 mm, and AlMg3, 1.0 mm) under a 60-ton hydraulic press. Measurements using digital image correlation (DIC) revealed minimal wear and deformation, with tolerances consistently within IT 0.1 mm. The results demonstrated that SLA-printed tools perform comparably to conventional metal tools in cutting and bending operations, achieving similar surface quality and edge precision while significantly reducing the production time and cost. Despite some limitations in wear resistance, the findings highlight SLA technology’s potential for rapid prototyping and short-run manufacturing in the automotive and electronics sectors. This research fills a critical gap in understanding SLA-based tooling applications, offering insights into process optimization to enhance tool durability and broaden material compatibility. These advancements position SLA technology as a transformative tool-making technology for flexible manufacturing.
- Open Access
- 6 January 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (1) , 442
Investigation of FDM-Based 3D Printing for Optimized Tooling in Automotive and Electronics Sheet Metal Cutting
Within the scope of the work, the possible use of fused deposition modeling (FDM) technology in executing rapid prototypes of cutting tools for aluminum sheets was systematically studied. Relevant investigations have thus far mainly concentrated on tools for the 3D printing of bent and deep-drawn pieces, yet the implementation of FDM tools in cutting has been insufficiently covered. This study aims to determine the characteristics of FDM cutting tools, such as wear and tear, dimensional stability, and cutting efficiency. Various tool designs were tested under different wall thicknesses and orientations with respect to the feed of Al99.5 sheets with thicknesses of 0.22 mm and 0.3 mm. According to the results, in the best case, three-dimensional printed PLA tools performed six cuts with no burrs and an acceptable wear level due to the IT tolerances (IT9 and IT10). Tools with thicker walls and more appropriate orientations were found to be more robust. However, some designs failed when subjected to greater loads, revealing a deficiency in some of the strength properties of the material. These observations suggest that it is possible to create 3D printed tools for modeling and small-scale production at considerably cheaper and faster rates than conventional methods. Future work will integrate advanced materials and designs to enhance tool performance, further solidifying FDM as a transformative approach in industrial tool manufacturing. With this research, the authors wanted to demonstrate that FDM technology can also be used to produce a classic sheet cut, which, of course, is still of great importance for prototyping or setting up production processes. This research demonstrated that FDM printing can play a role in this area.
- 6 January 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (1) , 442
Open AccessInvestigation of FDM-Based 3D Printing for Optimized Tooling in Automotive and Electronics Sheet Metal Cutting
Within the scope of the work, the possible use of fused deposition modeling (FDM) technology in executing rapid prototypes of cutting tools for aluminum sheets was systematically studied. Relevant investigations have thus far mainly concentrated on tools for the 3D printing of bent and deep-drawn pieces, yet the implementation of FDM tools in cutting has been insufficiently covered. This study aims to determine the characteristics of FDM cutting tools, such as wear and tear, dimensional stability, and cutting efficiency. Various tool designs were tested under different wall thicknesses and orientations with respect to the feed of Al99.5 sheets with thicknesses of 0.22 mm and 0.3 mm. According to the results, in the best case, three-dimensional printed PLA tools performed six cuts with no burrs and an acceptable wear level due to the IT tolerances (IT9 and IT10). Tools with thicker walls and more appropriate orientations were found to be more robust. However, some designs failed when subjected to greater loads, revealing a deficiency in some of the strength properties of the material. These observations suggest that it is possible to create 3D printed tools for modeling and small-scale production at considerably cheaper and faster rates than conventional methods. Future work will integrate advanced materials and designs to enhance tool performance, further solidifying FDM as a transformative approach in industrial tool manufacturing. With this research, the authors wanted to demonstrate that FDM technology can also be used to produce a classic sheet cut, which, of course, is still of great importance for prototyping or setting up production processes. This research demonstrated that FDM printing can play a role in this area.
- Open Access
- 7 November 2024
- Published by MDPI AG in Engineering Proceedings
- Vol. 79 (1) , 69
Testing Sustainable 3D-Printed Battery Housings with DIC Technology
Three-dimensional printing has rapidly gained traction in the automotive industry, offering significant benefits in terms of design flexibility, production speed, and cost efficiency. However, as the use of 3D printing grows, there is a rising focus on incorporating sustainable materials to minimize the environmental footprint of automotive components. This study centers on using eco-friendly, 3D-printable materials to produce electric vehicle battery covers. The primary goal is to assess these sustainable battery housings’ mechanical properties, durability, and overall feasibility. Additionally, the research explores the potential of foaming polylactic acid filaments in measurement applications using Digital Image Correlation technology, which is widely employed in the automotive sector. The study also evaluates these housings’ manufacturability and real-world applicability, offering insights into their role in the future of automotive production, where sustainability is becoming increasingly important. The research seeks to contribute to the broader movement toward greener manufacturing processes within the automotive industry by conducting these analyses.
- 7 November 2024
- Published by MDPI AG in Engineering Proceedings
- Vol. 79 (1) , 69
Open AccessTesting Sustainable 3D-Printed Battery Housings with DIC Technology
Three-dimensional printing has rapidly gained traction in the automotive industry, offering significant benefits in terms of design flexibility, production speed, and cost efficiency. However, as the use of 3D printing grows, there is a rising focus on incorporating sustainable materials to minimize the environmental footprint of automotive components. This study centers on using eco-friendly, 3D-printable materials to produce electric vehicle battery covers. The primary goal is to assess these sustainable battery housings’ mechanical properties, durability, and overall feasibility. Additionally, the research explores the potential of foaming polylactic acid filaments in measurement applications using Digital Image Correlation technology, which is widely employed in the automotive sector. The study also evaluates these housings’ manufacturability and real-world applicability, offering insights into their role in the future of automotive production, where sustainability is becoming increasingly important. The research seeks to contribute to the broader movement toward greener manufacturing processes within the automotive industry by conducting these analyses.