Brigitta Fruzsina Szívós
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Brigitta Fruzsina Szívós has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Vivien Nemes
Department of Vehicle Production and Engineering, Széchenyi István University, H-9026 Győr, Hungary
10 shared publications - Szabolcs Fischer
Central Campus Győr, Széchenyi István University, H-9026 Győr, Hungary
8 shared publications - Szabolcs Szalai
Department of Vehicle Production and Engineering, Széchenyi István University, Egyetem tér 1, 9026 Győr, Hungary
8 shared publications - Dmytro Kurhan
Department of Transport Infrastructure, Ukrainian State University of Science and Technologies, UA-49010 Dnipro, Ukraine
4 shared publications - Mykola Sysyn
Institute of Railway Systems and Public Transport, Technical University Dresden, 01069 Dresden, Germany
4 shared publications - György Szabó
Central Campus Győr, Széchenyi István University, H-9026 Győr, Hungary
2 shared publications
Latest Publications
- Open Access
- 19 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 40
Mechanical Performance of Heat-Set Threaded Inserts in FDM-Printed PLA Components
Heat-set threaded inserts provide a practical solution for reusable, load-bearing joints in FDM-printed polymer parts; however, their pull-out performance is governed not only by the insert itself, but also by the surrounding printed architecture. This study examines the pull-out behavior of heat-set M3 inserts embedded in FDM-printed PLA specimens across three wall thicknesses (1.28 mm, 1.6 mm, and 1.92 mm) and three infill patterns (adaptive cubic, cross-zag, and gyroid) using a repeatable drill-stand-based insertion fixture and a two-stage embedding protocol at 190 °C. Across 27 specimens, mean peak pull-out force ranged from 1353.6 ± 7.5 N to 1551.5 ± 20.4 N. Two-way ANOVA showed that both wall thickness and infill pattern significantly affected peak force, although the wall-thickness effect was practically modest—a 20% increase in material yielded only a 4.6% increase in mean force. Cross-zag specimens failed at significantly lower loads than adaptive cubic and gyroid, which performed comparably. Two specimens (7.4%) failed prematurely because of defective insert threads rather than the printed structure, underlining the importance of fastener quality control.
- 19 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 40
Open AccessMechanical Performance of Heat-Set Threaded Inserts in FDM-Printed PLA Components
Heat-set threaded inserts provide a practical solution for reusable, load-bearing joints in FDM-printed polymer parts; however, their pull-out performance is governed not only by the insert itself, but also by the surrounding printed architecture. This study examines the pull-out behavior of heat-set M3 inserts embedded in FDM-printed PLA specimens across three wall thicknesses (1.28 mm, 1.6 mm, and 1.92 mm) and three infill patterns (adaptive cubic, cross-zag, and gyroid) using a repeatable drill-stand-based insertion fixture and a two-stage embedding protocol at 190 °C. Across 27 specimens, mean peak pull-out force ranged from 1353.6 ± 7.5 N to 1551.5 ± 20.4 N. Two-way ANOVA showed that both wall thickness and infill pattern significantly affected peak force, although the wall-thickness effect was practically modest—a 20% increase in material yielded only a 4.6% increase in mean force. Cross-zag specimens failed at significantly lower loads than adaptive cubic and gyroid, which performed comparably. Two specimens (7.4%) failed prematurely because of defective insert threads rather than the printed structure, underlining the importance of fastener quality control.
- Open Access
- 19 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 33
Deformation Analysis of Bending Tests Using the GOM TRITOP System
This paper investigates the applicability of the GOM TRITOP photogrammetric system for displacement measurement in three-point bending tests of fused deposition modeling (FDM)-printed polylactic acid (PLA) specimens. Although TRITOP was originally developed primarily for the high-precision measurement of static object states, this study explores its extension toward deformation analysis by comparing discrete measurement stages recorded before loading and after fracture. In this sense, the method does not provide continuous deformation monitoring as in conventional digital image correlation (DIC)-based approaches, but enables marker-based displacement evaluation between defined loading states. Nine specimens manufactured from different commercial filaments and infill configurations were tested, and the TRITOP results were validated against digital dial-gauge measurements. The relative differences ranged from −1.3% to +2.3%, indicating good agreement. The system also enabled the simultaneous tracking of punch and specimen-end displacements, revealing differences between printing configurations and selected asymmetric bending responses. The results suggest that TRITOP can be practically extended to stage-based displacement analysis of additively manufactured components.
- 19 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 33
Open AccessDeformation Analysis of Bending Tests Using the GOM TRITOP System
This paper investigates the applicability of the GOM TRITOP photogrammetric system for displacement measurement in three-point bending tests of fused deposition modeling (FDM)-printed polylactic acid (PLA) specimens. Although TRITOP was originally developed primarily for the high-precision measurement of static object states, this study explores its extension toward deformation analysis by comparing discrete measurement stages recorded before loading and after fracture. In this sense, the method does not provide continuous deformation monitoring as in conventional digital image correlation (DIC)-based approaches, but enables marker-based displacement evaluation between defined loading states. Nine specimens manufactured from different commercial filaments and infill configurations were tested, and the TRITOP results were validated against digital dial-gauge measurements. The relative differences ranged from −1.3% to +2.3%, indicating good agreement. The system also enabled the simultaneous tracking of punch and specimen-end displacements, revealing differences between printing configurations and selected asymmetric bending responses. The results suggest that TRITOP can be practically extended to stage-based displacement analysis of additively manufactured components.
- Open Access
- 16 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 25
Evaluation of Dimensional Precision and Repeatability in MSLA Resin Printing
The dimensional precision and repeatability of an entry-level masked stereolithography (MSLA) printer were evaluated using a two-part fit gauge representative of a blanking tool, in which the peg-bore clearance served as the functionally critical dimension. Specimens were produced on an Elegoo Mars 5 Ultra (ELEGOO, Hongkong, China) using Elegoo Standard Resin (ELEGOO, Hongkong, China), with a fixed print configuration based on the manufacturer’s recommended settings. Two single-parameter post-processing series were examined by varying either the washing time or the post-cure time. At the same time, dimensional inspection was performed using a coordinate measuring machine (CMM) and, for one series, hand-held calipers. The fit-defining diameters were reproduced accurately and remained stable across all tested conditions, yielding a consistent diametric clearance. In contrast, the axial depths of recessed features were systematically undersized and were influenced more by print configuration than by post-processing duration. The results indicate that in-plane dimensions can be reproduced reliably, whereas Z-direction features require feature-specific compensation.
- 16 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 25
Open AccessEvaluation of Dimensional Precision and Repeatability in MSLA Resin Printing
The dimensional precision and repeatability of an entry-level masked stereolithography (MSLA) printer were evaluated using a two-part fit gauge representative of a blanking tool, in which the peg-bore clearance served as the functionally critical dimension. Specimens were produced on an Elegoo Mars 5 Ultra (ELEGOO, Hongkong, China) using Elegoo Standard Resin (ELEGOO, Hongkong, China), with a fixed print configuration based on the manufacturer’s recommended settings. Two single-parameter post-processing series were examined by varying either the washing time or the post-cure time. At the same time, dimensional inspection was performed using a coordinate measuring machine (CMM) and, for one series, hand-held calipers. The fit-defining diameters were reproduced accurately and remained stable across all tested conditions, yielding a consistent diametric clearance. In contrast, the axial depths of recessed features were systematically undersized and were influenced more by print configuration than by post-processing duration. The results indicate that in-plane dimensions can be reproduced reliably, whereas Z-direction features require feature-specific compensation.
- Open Access
Passive Thermal Management of Cylindrical Lithium-Ion Cells Using Additively Manufactured Polymer Housings
Lithium-ion batteries are widely used in modern energy storage systems; however, increasing power demand makes thermal management a critical challenge, particularly for cylindrical cells operating under high discharge conditions. This study investigates the thermal behavior of cylindrical lithium-ion cells equipped with additively manufactured polymer housings produced by fused filament fabrication (FFF). PLA, PCTG, flame-retardant PLA (FG_PLA), and ASA housings were evaluated using Samsung 50S, Molicel P42A, and Reliance RS50 cells under 1C–5C discharge rates. Surface temperatures were measured at multiple locations to assess heat transfer through the housing structures. All investigated housings reduced the measured maximum cell surface temperature compared with the housing-free configuration, particularly at high discharge rates. PLA exhibited the greatest thermal buffering effect, while PCTG showed the highest estimated conductive heat-transfer rate and a more uniform temperature evolution across the housing. ASA demonstrated stable thermal behavior, with thin housings generally showing a greater measured temperature reduction than thick configurations. In contrast, flame-retardant PLA provided the smallest temperature reduction. Wall thickness influenced the transient thermal response but did not consistently result in a greater measured temperature reduction. At elevated temperatures, partial deformation of some polymer housings was observed. The results demonstrate that FFF-manufactured polymer housings can substantially modify the transient thermal response of cylindrical lithium-ion cells, while material selection and housing geometry remain key design parameters for passive thermal management applications.
Open AccessPassive Thermal Management of Cylindrical Lithium-Ion Cells Using Additively Manufactured Polymer Housings
Lithium-ion batteries are widely used in modern energy storage systems; however, increasing power demand makes thermal management a critical challenge, particularly for cylindrical cells operating under high discharge conditions. This study investigates the thermal behavior of cylindrical lithium-ion cells equipped with additively manufactured polymer housings produced by fused filament fabrication (FFF). PLA, PCTG, flame-retardant PLA (FG_PLA), and ASA housings were evaluated using Samsung 50S, Molicel P42A, and Reliance RS50 cells under 1C–5C discharge rates. Surface temperatures were measured at multiple locations to assess heat transfer through the housing structures. All investigated housings reduced the measured maximum cell surface temperature compared with the housing-free configuration, particularly at high discharge rates. PLA exhibited the greatest thermal buffering effect, while PCTG showed the highest estimated conductive heat-transfer rate and a more uniform temperature evolution across the housing. ASA demonstrated stable thermal behavior, with thin housings generally showing a greater measured temperature reduction than thick configurations. In contrast, flame-retardant PLA provided the smallest temperature reduction. Wall thickness influenced the transient thermal response but did not consistently result in a greater measured temperature reduction. At elevated temperatures, partial deformation of some polymer housings was observed. The results demonstrate that FFF-manufactured polymer housings can substantially modify the transient thermal response of cylindrical lithium-ion cells, while material selection and housing geometry remain key design parameters for passive thermal management applications.
- Open Access
- 5 January 2026
- Published by Scientific Oasis in Spectrum of Engineering and Management Sciences
- Vol. 4 (1) , 233-254
Optimization of Speckle Pattern Generation for DIC-based Mechanical Characterization of Automotive Synthetic Leathers
Digital Image Correlation (DIC) is a pivotal non-contact technique for full-field deformation analysis in automotive engineering. However, the high flexibility and porosity of synthetic leathers often compromise speckle pattern stability and measurement accuracy. This study presents a systematic evaluation of commercial spray paints to optimize speckle pattern generation for automotive PVC and felt-based leathers. The methodology integrates standardized adhesion testing (ISO 2409 cross-cut test), drying-time optimization, and microscopic characterization to ensure robust bonding. Performance was validated through Erichsen cupping tests, simulating multi-axial strain states typical of automotive interior components. Results demonstrate that solvent-based acrylic sprays provide superior adhesion (ISO Class 0) and maintain pattern integrity under large deformations (up to 30% strain), whereas water-based alternatives suffer from cracking and delamination. The optimized painting protocol significantly reduces correlation errors and "lost subsets" in DIC software. This research provides a reliable experimental foundation for material characterization and Finite Element Method (FEM) validation of interior systems. The findings offer a practical, cost-effective framework for enhancing optical strain measurement precision in the automotive manufacturing and testing sectors.
- 5 January 2026
- Published by Scientific Oasis in Spectrum of Engineering and Management Sciences
- Vol. 4 (1) , 233-254
Open AccessOptimization of Speckle Pattern Generation for DIC-based Mechanical Characterization of Automotive Synthetic Leathers
Digital Image Correlation (DIC) is a pivotal non-contact technique for full-field deformation analysis in automotive engineering. However, the high flexibility and porosity of synthetic leathers often compromise speckle pattern stability and measurement accuracy. This study presents a systematic evaluation of commercial spray paints to optimize speckle pattern generation for automotive PVC and felt-based leathers. The methodology integrates standardized adhesion testing (ISO 2409 cross-cut test), drying-time optimization, and microscopic characterization to ensure robust bonding. Performance was validated through Erichsen cupping tests, simulating multi-axial strain states typical of automotive interior components. Results demonstrate that solvent-based acrylic sprays provide superior adhesion (ISO Class 0) and maintain pattern integrity under large deformations (up to 30% strain), whereas water-based alternatives suffer from cracking and delamination. The optimized painting protocol significantly reduces correlation errors and "lost subsets" in DIC software. This research provides a reliable experimental foundation for material characterization and Finite Element Method (FEM) validation of interior systems. The findings offer a practical, cost-effective framework for enhancing optical strain measurement precision in the automotive manufacturing and testing sectors.
- Open Access
- 7 November 2025
- Published by MDPI AG in Engineering Proceedings
- Vol. 113 (1) , 35
Measurement Errors and Challenges in Sheet Metal Components When Using Digital Image Correlation (DIC) Systems
Digital Image Correlation systems are increasingly being used for non-contact measurement of deformation and strain in sheet metal components. However, the accuracy of such measurements can be significantly affected by various external and system-related factors. If these are not properly considered, substantial errors may be introduced. In this study, a short and longer flat sheet specimen were clamped in a vise to investigate how overhang and clamping stability influence the accuracy of the measured deformation fields. Two different measurement volumes were also evaluated to assess their effect on the results. These factors were evaluated through targeted experiments, and the resulting data were analyzed and interpreted. Based on the findings, recommendations were formulated to enhance the reliability of Digital Image Correlation measurements in both laboratory and industrial environments.
- 7 November 2025
- Published by MDPI AG in Engineering Proceedings
- Vol. 113 (1) , 35
Open AccessMeasurement Errors and Challenges in Sheet Metal Components When Using Digital Image Correlation (DIC) Systems
Digital Image Correlation systems are increasingly being used for non-contact measurement of deformation and strain in sheet metal components. However, the accuracy of such measurements can be significantly affected by various external and system-related factors. If these are not properly considered, substantial errors may be introduced. In this study, a short and longer flat sheet specimen were clamped in a vise to investigate how overhang and clamping stability influence the accuracy of the measured deformation fields. Two different measurement volumes were also evaluated to assess their effect on the results. These factors were evaluated through targeted experiments, and the resulting data were analyzed and interpreted. Based on the findings, recommendations were formulated to enhance the reliability of Digital Image Correlation measurements in both laboratory and industrial environments.
- Open Access
- 7 August 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (15) , 8747
Investigation of the Load-Bearing Capacity of Resin-Printed Components Under Different Printing Strategies
This study examines the influence of different printing orientations and infill settings on the strength and flexibility of components produced using resin-based 3D printing, particularly with masked stereolithography (MSLA). Using a common photopolymer resin and a widely available desktop MSLA printer, we produced and tested a series of samples with varying tilt angles and internal structures. To understand their mechanical behavior, we applied a custom bending test combined with high-precision deformation tracking through the GOM ARAMIS digital image correlation system. The results obtained clearly show that both the angle of printing and the density of the internal infill structure play a significant role in how much strain the printed parts can handle before breaking. Notably, a 75° orientation provided the best deformation performance, and infill rates between 60% and 90% offered a good balance between strength and material efficiency. These findings highlight how adjusting print settings can lead to stronger parts while also saving time and resources—an important consideration for practical applications in engineering, design, and manufacturing.
- 7 August 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (15) , 8747
Open AccessInvestigation of the Load-Bearing Capacity of Resin-Printed Components Under Different Printing Strategies
This study examines the influence of different printing orientations and infill settings on the strength and flexibility of components produced using resin-based 3D printing, particularly with masked stereolithography (MSLA). Using a common photopolymer resin and a widely available desktop MSLA printer, we produced and tested a series of samples with varying tilt angles and internal structures. To understand their mechanical behavior, we applied a custom bending test combined with high-precision deformation tracking through the GOM ARAMIS digital image correlation system. The results obtained clearly show that both the angle of printing and the density of the internal infill structure play a significant role in how much strain the printed parts can handle before breaking. Notably, a 75° orientation provided the best deformation performance, and infill rates between 60% and 90% offered a good balance between strength and material efficiency. These findings highlight how adjusting print settings can lead to stronger parts while also saving time and resources—an important consideration for practical applications in engineering, design, and manufacturing.
- Open Access
Deformation Characterization of Glass Fiber and Carbon Fiber-Reinforced 3D Printing Filaments Using Digital Image Correlation
The paper offers an in-depth deformation study of glass fiber-reinforced and carbon composite filaments of 3D printers. During the certification, the authors used DIC (Digital Image Correlation) as a full-field strain measurement technique to explore key material traits as a non-contact optical measurement method. The insights captured through the DIC technology enabled to better understand the localized strain distributions during the loading of these reinforced filaments. The paper analyzes the glass fiber and carbon fiber filaments used in 3D printing that are reinforced with these materials and are subjected to bending and compressive loading. The segment presents how loading affects the performance of reinforced filaments when varying such factors as the deposition patterns, layer orientation, and other process parameters. Different types and combinations of reinforcements and printing variables were tested, and the resulting dependencies of mechanical parameters and failure modes were established for each case. Key conclusions demonstrate that the mechanical behavior of both carbon- and glass fiber-reinforced filaments is strongly affected by the 3D printing parameters, particularly infill density, pattern, and build orientation. The application of Digital Image Correlation (DIC) allowed for a precise, full-field analysis of strain distribution and deformation behavior, offering new insights into the structural performance of fiber-reinforced 3D printed composites. The findings from the study provide guidance for the proper choice of filling material and the optimal parameters for the 3D printing process of models with high-performance indexes and seamless applications in the automotive and industrial manufacturing sectors.
Open AccessDeformation Characterization of Glass Fiber and Carbon Fiber-Reinforced 3D Printing Filaments Using Digital Image Correlation
The paper offers an in-depth deformation study of glass fiber-reinforced and carbon composite filaments of 3D printers. During the certification, the authors used DIC (Digital Image Correlation) as a full-field strain measurement technique to explore key material traits as a non-contact optical measurement method. The insights captured through the DIC technology enabled to better understand the localized strain distributions during the loading of these reinforced filaments. The paper analyzes the glass fiber and carbon fiber filaments used in 3D printing that are reinforced with these materials and are subjected to bending and compressive loading. The segment presents how loading affects the performance of reinforced filaments when varying such factors as the deposition patterns, layer orientation, and other process parameters. Different types and combinations of reinforcements and printing variables were tested, and the resulting dependencies of mechanical parameters and failure modes were established for each case. Key conclusions demonstrate that the mechanical behavior of both carbon- and glass fiber-reinforced filaments is strongly affected by the 3D printing parameters, particularly infill density, pattern, and build orientation. The application of Digital Image Correlation (DIC) allowed for a precise, full-field analysis of strain distribution and deformation behavior, offering new insights into the structural performance of fiber-reinforced 3D printed composites. The findings from the study provide guidance for the proper choice of filling material and the optimal parameters for the 3D printing process of models with high-performance indexes and seamless applications in the automotive and industrial manufacturing sectors.
- 25 February 2025
- Published by Springer Nature
- p. 175-187
Production and Testing of 3D Printed PLA Structures with DIC Technology for the Reinforcement of Concrete Elements
- 25 February 2025
- Published by Springer Nature
- p. 175-187
Production and Testing of 3D Printed PLA Structures with DIC Technology for the Reinforcement of Concrete Elements
- Open Access
- 15 January 2025
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 9 (1) , 25
Investigation of Digital Light Processing-Based 3D Printing for Optimized Tooling in Automotive and Electronics Sheet Metal Forming
This study addresses the emerging need for efficient and cost-effective solutions in low-volume production by exploring the mechanical performance and industrial feasibility of cutting tools that are fabricated using stereolithography apparatus (SLA) technology. SLA’s high-resolution capabilities make it suitable for creating precise cutting dies, which were tested on aluminum sheets (Al99.5, 0.3 mm, and AlMg3, 1.0 mm) under a 60-ton hydraulic press. Measurements using digital image correlation (DIC) revealed minimal wear and deformation, with tolerances consistently within IT 0.1 mm. The results demonstrated that SLA-printed tools perform comparably to conventional metal tools in cutting and bending operations, achieving similar surface quality and edge precision while significantly reducing the production time and cost. Despite some limitations in wear resistance, the findings highlight SLA technology’s potential for rapid prototyping and short-run manufacturing in the automotive and electronics sectors. This research fills a critical gap in understanding SLA-based tooling applications, offering insights into process optimization to enhance tool durability and broaden material compatibility. These advancements position SLA technology as a transformative tool-making technology for flexible manufacturing.
- 15 January 2025
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 9 (1) , 25
Open AccessInvestigation of Digital Light Processing-Based 3D Printing for Optimized Tooling in Automotive and Electronics Sheet Metal Forming
This study addresses the emerging need for efficient and cost-effective solutions in low-volume production by exploring the mechanical performance and industrial feasibility of cutting tools that are fabricated using stereolithography apparatus (SLA) technology. SLA’s high-resolution capabilities make it suitable for creating precise cutting dies, which were tested on aluminum sheets (Al99.5, 0.3 mm, and AlMg3, 1.0 mm) under a 60-ton hydraulic press. Measurements using digital image correlation (DIC) revealed minimal wear and deformation, with tolerances consistently within IT 0.1 mm. The results demonstrated that SLA-printed tools perform comparably to conventional metal tools in cutting and bending operations, achieving similar surface quality and edge precision while significantly reducing the production time and cost. Despite some limitations in wear resistance, the findings highlight SLA technology’s potential for rapid prototyping and short-run manufacturing in the automotive and electronics sectors. This research fills a critical gap in understanding SLA-based tooling applications, offering insights into process optimization to enhance tool durability and broaden material compatibility. These advancements position SLA technology as a transformative tool-making technology for flexible manufacturing.