Sara El Afia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sara El Afia has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Cano
Department of Electrical Engineering, University of Jaén, 23071 Jaén, Spain
5 shared publications - Francisco Jurado
Department of Electrical Engineering, University of Jaén, 23071 Jaén, Spain
5 shared publications - Paul Arévalo
Department of Electrical Engineering, Electronics and Telecommunications, Universidad de Cuenca, Cuenca 010101, Ecuador
2 shared publications - Rachid Hidki
National School of Applied Sciences (ENSA), Sultan Moulay Slimane University Beni Mellal Morocco
1 shared publication - Raja Mazuir Raja Ahsan Shah
Centre of Excellence for Sustainable Mobility, University of Doha for Science and Technology, Doha 24449, Qatar
1 shared publication
Latest Publications
- Open Access
Thermo-Hydraulic Performance Assessment of Al2O3–Mineral Oil Nanofluids for Direct Immersion Cooling of Lithium-Ion Battery Packs Under Fast-Charging
The increasing thermal load associated with fast charging represents a major challenge for lithium-ion battery thermal management, particularly at high C-rates where conventional air cooling becomes insufficient. This study numerically investigates the thermo-hydraulic performance of Al2O3–mineral oil nanofluids for direct immersion cooling of an 18650 lithium-ion battery pack under fast-charging conditions. A three-dimensional transient CFD model is employed to evaluate Al2O3 volume fractions ranging from 0 to 1.0 vol.%, while the effects of charging rate and coolant inlet velocity are systematically examined. Thermal performance is assessed in terms of maximum cell temperature and temperature uniformity, together with pressure drop and pumping power to account for the associated hydraulic penalty. The results demonstrate that increasing the Al2O3 concentration progressively improves battery cooling and temperature uniformity compared with pure mineral oil, although the corresponding increase in flow resistance reveals a clear thermo-hydraulic trade-off. Increasing the charging rate from 2C to 8C substantially intensifies the thermal load, with the maximum cell temperature reaching 340.47 K at 8C, indicating that nanoparticle enhancement alone may be insufficient under ultra-fast charging. Increasing the coolant velocity from 0.05 to 0.20 m/s under 8C operation reduces the maximum cell temperature from 329.61 to 318.37 K, demonstrating the strong contribution of forced convection to thermal regulation. However, the pressure drop simultaneously increases from 23.89 to 114.57 Pa, accompanied by increased pumping-power demand. Among the investigated cases, 1 vol.% Al2O3 at 0.20 m/s provides the strongest thermal performance under 8C fast charging. These findings highlight the importance of considering both nanoparticle concentration and coolant inlet velocity when evaluating the thermal performance and associated hydraulic requirements of dielectric nanofluid immersion cooling systems under high-rate and ultra-fast-charging conditions.
Open AccessThermo-Hydraulic Performance Assessment of Al2O3–Mineral Oil Nanofluids for Direct Immersion Cooling of Lithium-Ion Battery Packs Under Fast-Charging
The increasing thermal load associated with fast charging represents a major challenge for lithium-ion battery thermal management, particularly at high C-rates where conventional air cooling becomes insufficient. This study numerically investigates the thermo-hydraulic performance of Al2O3–mineral oil nanofluids for direct immersion cooling of an 18650 lithium-ion battery pack under fast-charging conditions. A three-dimensional transient CFD model is employed to evaluate Al2O3 volume fractions ranging from 0 to 1.0 vol.%, while the effects of charging rate and coolant inlet velocity are systematically examined. Thermal performance is assessed in terms of maximum cell temperature and temperature uniformity, together with pressure drop and pumping power to account for the associated hydraulic penalty. The results demonstrate that increasing the Al2O3 concentration progressively improves battery cooling and temperature uniformity compared with pure mineral oil, although the corresponding increase in flow resistance reveals a clear thermo-hydraulic trade-off. Increasing the charging rate from 2C to 8C substantially intensifies the thermal load, with the maximum cell temperature reaching 340.47 K at 8C, indicating that nanoparticle enhancement alone may be insufficient under ultra-fast charging. Increasing the coolant velocity from 0.05 to 0.20 m/s under 8C operation reduces the maximum cell temperature from 329.61 to 318.37 K, demonstrating the strong contribution of forced convection to thermal regulation. However, the pressure drop simultaneously increases from 23.89 to 114.57 Pa, accompanied by increased pumping-power demand. Among the investigated cases, 1 vol.% Al2O3 at 0.20 m/s provides the strongest thermal performance under 8C fast charging. These findings highlight the importance of considering both nanoparticle concentration and coolant inlet velocity when evaluating the thermal performance and associated hydraulic requirements of dielectric nanofluid immersion cooling systems under high-rate and ultra-fast-charging conditions.
- Open Access
Computational Fluid Dynamics Analysis of Battery Immersion Cooling: Impact of Dielectric Fluid Thermophysical Properties
The rapid growth in the electric vehicle sector has increased demand for advanced battery thermal management systems (BTMSs) with high heat-dissipation capacity and temperature uniformity. Immersion cooling using dielectric fluids has recently been recognized as a promising alternative technology to conventional indirect liquid cooling methods. This study investigates the thermal and hydrodynamic behaviour of a sixteen-lithium-ion cell battery (LIB) module immersed in low-viscosity dielectric fluids using three-dimensional computational fluid dynamics simulations. In this context, a total of twenty dielectric fluids are evaluated using the ANSYS Fluent solver, with particular emphasis on the effects of key thermophysical properties, including viscosity, density, specific heat capacity, and thermal conductivity. The simulation findings reveal that mineral oil and PAO4 yield the lowest maximum LIB cell temperatures, with a reduction of approximately 4 K compared to the least effective dielectric fluids, such as undecane and cumene. Moreover, in terms of temperature uniformity, mineral oil, Novec 7000, and PAO4 exhibit the most homogeneous temperature distributions among the twenty dielectric fluids. In addition, they show an improvement in the temperature uniformity index of approximately 32.4% compared with the least effective dielectric fluid, cumene. On the other hand, mineral oil and PAO4 generate significantly higher pressure drops because of their relatively high viscosities, which increases hydraulic resistance and pumping power requirements. These findings demonstrate that excellent thermal performance does not necessarily correspond to optimal overall thermo-hydraulic behaviour. Overall, the results confirm that immersion-BTMS performance is governed by a complex interaction between dielectric fluid thermophysical properties and flow behaviour, highlighting the importance of coupled thermo-hydraulic optimization in the selection of dielectric fluids for next-generation immersion-cooled battery systems.
Open AccessComputational Fluid Dynamics Analysis of Battery Immersion Cooling: Impact of Dielectric Fluid Thermophysical Properties
The rapid growth in the electric vehicle sector has increased demand for advanced battery thermal management systems (BTMSs) with high heat-dissipation capacity and temperature uniformity. Immersion cooling using dielectric fluids has recently been recognized as a promising alternative technology to conventional indirect liquid cooling methods. This study investigates the thermal and hydrodynamic behaviour of a sixteen-lithium-ion cell battery (LIB) module immersed in low-viscosity dielectric fluids using three-dimensional computational fluid dynamics simulations. In this context, a total of twenty dielectric fluids are evaluated using the ANSYS Fluent solver, with particular emphasis on the effects of key thermophysical properties, including viscosity, density, specific heat capacity, and thermal conductivity. The simulation findings reveal that mineral oil and PAO4 yield the lowest maximum LIB cell temperatures, with a reduction of approximately 4 K compared to the least effective dielectric fluids, such as undecane and cumene. Moreover, in terms of temperature uniformity, mineral oil, Novec 7000, and PAO4 exhibit the most homogeneous temperature distributions among the twenty dielectric fluids. In addition, they show an improvement in the temperature uniformity index of approximately 32.4% compared with the least effective dielectric fluid, cumene. On the other hand, mineral oil and PAO4 generate significantly higher pressure drops because of their relatively high viscosities, which increases hydraulic resistance and pumping power requirements. These findings demonstrate that excellent thermal performance does not necessarily correspond to optimal overall thermo-hydraulic behaviour. Overall, the results confirm that immersion-BTMS performance is governed by a complex interaction between dielectric fluid thermophysical properties and flow behaviour, highlighting the importance of coupled thermo-hydraulic optimization in the selection of dielectric fluids for next-generation immersion-cooled battery systems.
- Open Access
Numerical Investigation into 18650 Li-Ion Battery Temperature Control Applying Immersion Cooling with FC-40 Dielectric Fluid
Nowadays, immersion cooling-based battery thermal management systems have demonstrated their effectiveness in controlling the temperature of lithium-ion batteries. While previous scientific research has primarily concentrated on traditional dielectric fluids such as mineral oil, the current research investigates the effectiveness of the dielectric fluid FC-40. A three-dimensional Computational Fluid Dynamics model of an eight-cell 18650 battery system was constructed using ANSYS Fluent 19.2 to examine the effect of cooling fluids (air, mineral oil, and FC-40), velocity of flow (0.01 m/s to 0.15 m/s), discharge rate (1C to 5C), and inlet/outlet size (2.5 mm to 3.5 mm) on thermal efficiency as well as pressure drop. The findings indicate that employing FC-40 as the dielectric fluid significantly reduces the peak cell temperature, with an absolute decrease of 2.80 °C compared to mineral oil and 15.10 °C compared to air. Furthermore, FC-40 achieves the highest uniformity with minimal hotspot. On the other hand, as the fluid velocity increases, the maximum temperature of the battery drops, reaching a minimum of 26 °C at a velocity of 0.15 m/s. Otherwise, at lower flow velocities, the pressure drop remains minimal, thereby reducing the pumping power consumption. Additionally, increasing the inlet and outlet diameter of the fluid directly improves cooling uniformity. Consequently, the temperature dropped by up to 4.3%. Finally, the findings demonstrate that elevated discharge rates contribute to increased heat dissipation but adversely affect the efficiency of the thermal management system. This study provides critical knowledge for the enhancement of battery thermal management systems based on immersion cooling using FC-40 as a dielectric.
Open AccessNumerical Investigation into 18650 Li-Ion Battery Temperature Control Applying Immersion Cooling with FC-40 Dielectric Fluid
Nowadays, immersion cooling-based battery thermal management systems have demonstrated their effectiveness in controlling the temperature of lithium-ion batteries. While previous scientific research has primarily concentrated on traditional dielectric fluids such as mineral oil, the current research investigates the effectiveness of the dielectric fluid FC-40. A three-dimensional Computational Fluid Dynamics model of an eight-cell 18650 battery system was constructed using ANSYS Fluent 19.2 to examine the effect of cooling fluids (air, mineral oil, and FC-40), velocity of flow (0.01 m/s to 0.15 m/s), discharge rate (1C to 5C), and inlet/outlet size (2.5 mm to 3.5 mm) on thermal efficiency as well as pressure drop. The findings indicate that employing FC-40 as the dielectric fluid significantly reduces the peak cell temperature, with an absolute decrease of 2.80 °C compared to mineral oil and 15.10 °C compared to air. Furthermore, FC-40 achieves the highest uniformity with minimal hotspot. On the other hand, as the fluid velocity increases, the maximum temperature of the battery drops, reaching a minimum of 26 °C at a velocity of 0.15 m/s. Otherwise, at lower flow velocities, the pressure drop remains minimal, thereby reducing the pumping power consumption. Additionally, increasing the inlet and outlet diameter of the fluid directly improves cooling uniformity. Consequently, the temperature dropped by up to 4.3%. Finally, the findings demonstrate that elevated discharge rates contribute to increased heat dissipation but adversely affect the efficiency of the thermal management system. This study provides critical knowledge for the enhancement of battery thermal management systems based on immersion cooling using FC-40 as a dielectric.
- Open Access
Rechargeable Li-Ion Batteries, Nanocomposite Materials and Applications
Lithium-ion batteries (LIBs) are pivotal in a wide range of applications, including consumer electronics, electric vehicles, and stationary energy storage systems. The broader adoption of LIBs hinges on advancements in their safety, cost-effectiveness, cycle life, energy density, and rate capability. While traditional LIBs already benefit from composite materials in components such as the cathode, anode, and separator, the integration of nanocomposite materials presents significant potential for enhancing these properties. Nanocomposites, including carbon–oxide, polymer–oxide, and silicon-based variants, are engineered to optimize key performance metrics, such as electrical conductivity, structural stability, capacity, and charging/discharging efficiency. Recent research has focused on refining these composites to overcome existing limitations in energy density and cycle life, thus paving the way for the next generation of LIB technologies. Despite these advancements, challenges related to high production costs and scalability remain substantial barriers to the widespread commercial deployment of nanocomposite-enhanced LIBs. Addressing these challenges is essential for realizing the full potential of these advanced materials, thereby driving significant improvements in the performance and practical applications of LIBs across various industries.
Open AccessRechargeable Li-Ion Batteries, Nanocomposite Materials and Applications
Lithium-ion batteries (LIBs) are pivotal in a wide range of applications, including consumer electronics, electric vehicles, and stationary energy storage systems. The broader adoption of LIBs hinges on advancements in their safety, cost-effectiveness, cycle life, energy density, and rate capability. While traditional LIBs already benefit from composite materials in components such as the cathode, anode, and separator, the integration of nanocomposite materials presents significant potential for enhancing these properties. Nanocomposites, including carbon–oxide, polymer–oxide, and silicon-based variants, are engineered to optimize key performance metrics, such as electrical conductivity, structural stability, capacity, and charging/discharging efficiency. Recent research has focused on refining these composites to overcome existing limitations in energy density and cycle life, thus paving the way for the next generation of LIB technologies. Despite these advancements, challenges related to high production costs and scalability remain substantial barriers to the widespread commercial deployment of nanocomposite-enhanced LIBs. Addressing these challenges is essential for realizing the full potential of these advanced materials, thereby driving significant improvements in the performance and practical applications of LIBs across various industries.
- Open Access
Energy Sources and Battery Thermal Energy Management Technologies for Electrical Vehicles: A Technical Comprehensive Review
Electric vehicles are increasingly seen as a viable alternative to conventional combustion-engine vehicles, offering advantages such as lower emissions and enhanced energy efficiency. The critical role of batteries in EVs drives the need for high-performance, cost-effective, and safe solutions, where thermal management is key to ensuring optimal performance and longevity. This study is motivated by the need to address the limitations of current battery thermal management systems (BTMS), particularly the effectiveness of cooling methods in maintaining safe operating temperatures. The hypothesis is that immersion cooling offers superior thermal regulation compared to the widely used indirect liquid cooling approach. Using MATLAB Simulink, this research investigates the dynamic thermal behaviour of three cooling systems, including air cooling, indirect liquid cooling, and immersion cooling, by comparing their performance with an uncooled battery. The results show that immersion cooling outperforms indirect liquid cooling in terms of temperature control and safety, providing a more efficient solution. These findings challenge the existing literature, positioning immersion cooling as the optimal BTMS. The main contribution of this paper lies in its comprehensive evaluation of cooling technologies and its validation of immersion cooling as a superior method for enhancing EV battery performance.
Open AccessEnergy Sources and Battery Thermal Energy Management Technologies for Electrical Vehicles: A Technical Comprehensive Review
Electric vehicles are increasingly seen as a viable alternative to conventional combustion-engine vehicles, offering advantages such as lower emissions and enhanced energy efficiency. The critical role of batteries in EVs drives the need for high-performance, cost-effective, and safe solutions, where thermal management is key to ensuring optimal performance and longevity. This study is motivated by the need to address the limitations of current battery thermal management systems (BTMS), particularly the effectiveness of cooling methods in maintaining safe operating temperatures. The hypothesis is that immersion cooling offers superior thermal regulation compared to the widely used indirect liquid cooling approach. Using MATLAB Simulink, this research investigates the dynamic thermal behaviour of three cooling systems, including air cooling, indirect liquid cooling, and immersion cooling, by comparing their performance with an uncooled battery. The results show that immersion cooling outperforms indirect liquid cooling in terms of temperature control and safety, providing a more efficient solution. These findings challenge the existing literature, positioning immersion cooling as the optimal BTMS. The main contribution of this paper lies in its comprehensive evaluation of cooling technologies and its validation of immersion cooling as a superior method for enhancing EV battery performance.