B. Prabhakaran
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
B. Prabhakaran has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
P. Sivaraj
Centre for Materials Joining and Research (CEMAJOR), Department of Manufacturing Engineering, Annamalai University
2 shared publicationsS. Malarvizhi
Centre for Materials Joining and Research (CEMAJOR), Department of Manufacturing Engineering, Annamalai University
2 shared publicationsV. Balasubramanian
Centre for Materials Joining and Research (CEMAJOR), Department of Manufacturing Engineering, Annamalai University
2 shared publications- Paramasivam Sivaraj
Mechanical Engineering, Annamalai University, Annamalai University, Annamalai Nagar, 608002, INDIA
1 shared publication - Senthilnathan K
Department of Mechanical Engineering, College of EngineeringGuindy , Anna University, Chennai-600025, Tamil Nadu, India
1 shared publication - Thirumavalavan Krishnamurthy
Department of Mechanical Engineering, College of EngineeringGuindy , Anna University, Chennai-600025, Tamil Nadu, India
1 shared publication
Latest Publications
- Open Access
- 19 March 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (7)
Influence of Tool Traverse Speed on Microstructural Characteristics and Mechanical Properties of Friction Stir Processed AA5754 Aluminium Alloy Under Overlap Configuration
AA5754-H111, a non-heat-treatable aluminium alloy of the 5000 series, is widely used in automotive and marine structures owing to its good strength-to-weight ratio, with strength enhancement achieved through strain hardening. Friction Stir Processing (FSP), derived from the Friction Stir Welding (FSW) technique, is increasingly applied to refine microstructures in the stir zone under solid-state conditions, thereby avoiding solidification-related defects. The effectiveness of FSP depends largely on three process parameters: tool rotational speed, tool traverse speed, and tool tilt angle. Although considerable work has been conducted on these parameters for aluminium alloys, the influence of tool traverse speed on AA5754 under overlap configuration has not been reported. In this study, two overlapped AA5754 plates (6 mm each) were processed using a tapered threaded HSS tool at three different traverse speeds (10, 15, and 20 mm/min), with other parameters kept constant. Post-FSP, the stir zone was examined through optical microscopy and XRD analysis, and tensile properties were evaluated. Results revealed that a traverse speed of 15 mm/min produced a defect-free stir zone and delivered the highest tensile properties, with an ultimate tensile strength of 232 MPa, yield strength of 192 MPa, and elongation of 37%, compared to the base metal values of 181 MPa, 167 MPa, and 14%, respectively. From the micro-structural evaluation, it is observed that the formation of a fine, equiaxed dynamically recrystallized grain structure in the stir zone, along with reduced grain size and homogeneous microstructural distribution as compared to the base material. The findings confirm that tool traverse speed critically controls heat generation and thereby governs microstructural refinement and mechanical performance of AA5754 alloy joints.
- 19 March 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (7)
Open AccessInfluence of Tool Traverse Speed on Microstructural Characteristics and Mechanical Properties of Friction Stir Processed AA5754 Aluminium Alloy Under Overlap Configuration
AA5754-H111, a non-heat-treatable aluminium alloy of the 5000 series, is widely used in automotive and marine structures owing to its good strength-to-weight ratio, with strength enhancement achieved through strain hardening. Friction Stir Processing (FSP), derived from the Friction Stir Welding (FSW) technique, is increasingly applied to refine microstructures in the stir zone under solid-state conditions, thereby avoiding solidification-related defects. The effectiveness of FSP depends largely on three process parameters: tool rotational speed, tool traverse speed, and tool tilt angle. Although considerable work has been conducted on these parameters for aluminium alloys, the influence of tool traverse speed on AA5754 under overlap configuration has not been reported. In this study, two overlapped AA5754 plates (6 mm each) were processed using a tapered threaded HSS tool at three different traverse speeds (10, 15, and 20 mm/min), with other parameters kept constant. Post-FSP, the stir zone was examined through optical microscopy and XRD analysis, and tensile properties were evaluated. Results revealed that a traverse speed of 15 mm/min produced a defect-free stir zone and delivered the highest tensile properties, with an ultimate tensile strength of 232 MPa, yield strength of 192 MPa, and elongation of 37%, compared to the base metal values of 181 MPa, 167 MPa, and 14%, respectively. From the micro-structural evaluation, it is observed that the formation of a fine, equiaxed dynamically recrystallized grain structure in the stir zone, along with reduced grain size and homogeneous microstructural distribution as compared to the base material. The findings confirm that tool traverse speed critically controls heat generation and thereby governs microstructural refinement and mechanical performance of AA5754 alloy joints.
- 16 December 2024
- Published by Taylor & Francis in Welding International
- Vol. 39 (3) , 257-267
Assessment on wire-arc additive manufactured high strength low alloy steel cylindrical component
- 16 December 2024
- Published by Taylor & Francis in Welding International
- Vol. 39 (3) , 257-267
Assessment on wire-arc additive manufactured high strength low alloy steel cylindrical component
- 15 November 2024
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 13 (6) , 1197-1200
Impact of Differential Cooling Rates on Wire Arc Additive Manufactured HSLA Steel Component
- 15 November 2024
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 13 (6) , 1197-1200
Impact of Differential Cooling Rates on Wire Arc Additive Manufactured HSLA Steel Component