Nazik Abdulwahid Jebur
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nazik Abdulwahid Jebur has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Zahra Khalid Hamdan
Mechanical Engineering Department, College of Engineering, Mustansiriyah University, Baghdad, Iraq
3 shared publications - Zaineb Waired Metteb
Mechanical Engineering Department, College of Engineering, Mustansiriyah University, Baghdad, Iraq
3 shared publications - Ahmed Ali Farhan Ogaili
Mechanical Engineering Department, College of Engineering, Mustansiriyah University, Baghdad, Iraq
2 shared publications - Fadhel Abbas Abdulla
Department of Mechanical Engineering, College of Engineering, Mustansiriyah University. Baghdad, Iraq
2 shared publications - Ehsan Sabah Al-Ameen
Mechanical Engineering Department, College of Engineering, Mustansiriyah University, Baghdad, Iraq
1 shared publication - Fadhel Abbas Abdulla
College of Engineering, Al-Mustansiriayah University, Baghdad, Iraq
1 shared publication
Latest Publications
- Open Access
- 1 March 2026
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 30 (2) , 253-261
Mechanical and Sustainable Performance of Polyester Composites with Glass and Natural Waste Fiber Fillers
This study unveils the innovative potential of polyester composites reinforced with natural fibers and fiberglass. By harnessing these recyclables as reinforcements, Eco-friendly practices and waste reduction are not only championed but also significantly enhance the mechanical properties of the composites. The samples of the composite were meticulously crafted by hand using compression moulding and lay-up procedures. The incorporation of one or two layers of woven fiberglass results in a substantial increase in tensile strength, with enhancements of 44% and 81% under the tensile test and 32.2% and 48.3% under the flexural strength, respectively, compared to unreinforced polyester. This superior performance is attributed to the surface energy and acid-base properties of the glass fibers, which facilitate matrix adhesion. Moreover, the integration of ground walnut shells and tree leaves into polyester amplifies tensile strength and strain, with 20% being the optimal ratio. Ground walnut shells exhibit superior performance compared to tree leaves, particularly in hybrid composites. However, the addition of natural fibers to polyester reinforced with fiberglass diminishes stress values to varying degrees due to factors such as poor bonding and uneven distribution. Overall, the study underscores the importance of fiber type and reinforcement configuration in optimizing the mechanical properties of polyester composites, while also inspiring a shift towards more sustainable and eco-friendly materials.
- 1 March 2026
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 30 (2) , 253-261
Open AccessMechanical and Sustainable Performance of Polyester Composites with Glass and Natural Waste Fiber Fillers
This study unveils the innovative potential of polyester composites reinforced with natural fibers and fiberglass. By harnessing these recyclables as reinforcements, Eco-friendly practices and waste reduction are not only championed but also significantly enhance the mechanical properties of the composites. The samples of the composite were meticulously crafted by hand using compression moulding and lay-up procedures. The incorporation of one or two layers of woven fiberglass results in a substantial increase in tensile strength, with enhancements of 44% and 81% under the tensile test and 32.2% and 48.3% under the flexural strength, respectively, compared to unreinforced polyester. This superior performance is attributed to the surface energy and acid-base properties of the glass fibers, which facilitate matrix adhesion. Moreover, the integration of ground walnut shells and tree leaves into polyester amplifies tensile strength and strain, with 20% being the optimal ratio. Ground walnut shells exhibit superior performance compared to tree leaves, particularly in hybrid composites. However, the addition of natural fibers to polyester reinforced with fiberglass diminishes stress values to varying degrees due to factors such as poor bonding and uneven distribution. Overall, the study underscores the importance of fiber type and reinforcement configuration in optimizing the mechanical properties of polyester composites, while also inspiring a shift towards more sustainable and eco-friendly materials.
- 13 June 2025
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 87 (4) , 707-716
EFFECTIVENESS OF DIFFERENT DAMPING PAD GEOMETRIES IN REDUCING VIBRATION
This study aims to evaluate the effectiveness of different geometric shapes of damping pads in reducing vibrations, focusing on square, rectangular, triangular, and circular shapes. The pads were designed to have the same surface area, thickness, and materials to ensure a fair comparison. The main objective is to determine the most efficient shape for vibration reduction, especially in applications that require a quiet environment, such as vaporizer devices for asthma patients. Vibration velocity and displacement data were analyzed using MATLAB. The results showed that rectangular pads were the most effective, with a vibration velocity of 6.2 mm/s and a displacement of 0.0496 mm, achieving reduction percentages of 34.7% and 42.99%, respectively. The square shape demonstrated good stability with a vibration velocity of 7 mm/s and a displacement of 0.0565 mm, with reduction percentages of 26.3% and 35.2%. Triangular and circular pads were the least efficient in reducing vibrations. This study indicates that rectangular and square shapes are the most effective in reducing vibrations, making them suitable for applications that require a stable and quiet environment.
- 13 June 2025
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 87 (4) , 707-716
EFFECTIVENESS OF DIFFERENT DAMPING PAD GEOMETRIES IN REDUCING VIBRATION
This study aims to evaluate the effectiveness of different geometric shapes of damping pads in reducing vibrations, focusing on square, rectangular, triangular, and circular shapes. The pads were designed to have the same surface area, thickness, and materials to ensure a fair comparison. The main objective is to determine the most efficient shape for vibration reduction, especially in applications that require a quiet environment, such as vaporizer devices for asthma patients. Vibration velocity and displacement data were analyzed using MATLAB. The results showed that rectangular pads were the most effective, with a vibration velocity of 6.2 mm/s and a displacement of 0.0496 mm, achieving reduction percentages of 34.7% and 42.99%, respectively. The square shape demonstrated good stability with a vibration velocity of 7 mm/s and a displacement of 0.0565 mm, with reduction percentages of 26.3% and 35.2%. Triangular and circular pads were the least efficient in reducing vibrations. This study indicates that rectangular and square shapes are the most effective in reducing vibrations, making them suitable for applications that require a stable and quiet environment.
- Open Access
- 4 June 2025
- Published by Tribologia - Finnish Journal of Tribology in Tribologia - Finnish Journal of Tribology
- Vol. 42 (1–2) , 24-34
Comparative analysis of grease types on bearing performance: time-frequency and statistical investigations
This study focuses on evaluating the behavior of three commercially available lithium-based lubricating greases—77 EP (from 77 Lubricants), LGMP3 (AXCL Lubes), and LHTG3 (XADO)—when applied to journal bearings operating at low (600 RPM) and high (2400 RPM) speeds. The purpose is to understand how different grease types influence the vibration performance of bearings under dynamic conditions. The analysis includes both time-domain statistical indicators and vibration characteristics in the frequency domain. Measurements such as RMS, standard deviation, skewness, kurtosis, and variance were gathered using a real-time LabVIEW setup. These metrics helped in identifying differences in system response under each lubrication condition. The outcomes revealed that higher rotational speeds significantly amplified both vibration levels and system irregularities. This behavior demonstrates the critical impact of selecting the proper lubricant, particularly in fast-moving machinery. Among the samples tested, LHTG3 achieved the most consistent results, showing lower fluctuations in vibration readings, which implies effective damping properties. LGMP3, on the other hand, showed greater variability in its data, suggesting reduced vibration stability. Although 77 EP did not score highest in time-domain statistics, it performed strongly in frequency-based analysis, reducing the effect of sudden shocks and high-frequency responses Long-term performance could benefit from LHTG3; 77 EP would be preferable for machines with varying or fast dynamic loads. These results underline the need of choosing lubricant for stability and condition of journal bearings.
- 4 June 2025
- Published by Tribologia - Finnish Journal of Tribology in Tribologia - Finnish Journal of Tribology
- Vol. 42 (1–2) , 24-34
Open AccessComparative analysis of grease types on bearing performance: time-frequency and statistical investigations
This study focuses on evaluating the behavior of three commercially available lithium-based lubricating greases—77 EP (from 77 Lubricants), LGMP3 (AXCL Lubes), and LHTG3 (XADO)—when applied to journal bearings operating at low (600 RPM) and high (2400 RPM) speeds. The purpose is to understand how different grease types influence the vibration performance of bearings under dynamic conditions. The analysis includes both time-domain statistical indicators and vibration characteristics in the frequency domain. Measurements such as RMS, standard deviation, skewness, kurtosis, and variance were gathered using a real-time LabVIEW setup. These metrics helped in identifying differences in system response under each lubrication condition. The outcomes revealed that higher rotational speeds significantly amplified both vibration levels and system irregularities. This behavior demonstrates the critical impact of selecting the proper lubricant, particularly in fast-moving machinery. Among the samples tested, LHTG3 achieved the most consistent results, showing lower fluctuations in vibration readings, which implies effective damping properties. LGMP3, on the other hand, showed greater variability in its data, suggesting reduced vibration stability. Although 77 EP did not score highest in time-domain statistics, it performed strongly in frequency-based analysis, reducing the effect of sudden shocks and high-frequency responses Long-term performance could benefit from LHTG3; 77 EP would be preferable for machines with varying or fast dynamic loads. These results underline the need of choosing lubricant for stability and condition of journal bearings.
- 8 May 2025
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 25 (3) , 1167-1180
Fault Diagnosis of Journal Bearings Using Vibration Analysis and Machine Learning Techniques
- 8 May 2025
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 25 (3) , 1167-1180
Fault Diagnosis of Journal Bearings Using Vibration Analysis and Machine Learning Techniques
- Open Access
- 1 January 2025
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 53 (3) , 401-408
Wear fault diagnosis in journal bearings using vibration analysis and AI
In this study, machine learning models for identifying wear defects in journal bearings under various operating circumstances are compared. Healthy, low, and high wear states were simulated using an experimental test rig. Information Gain, Gain Ratio, Gini Index, and other feature selection techniques were used to analyze vibration signals from precision sensors. Relevance was used to rank features like Root Mean Square, Peak-to-Peak, and Peak. Using accuracy, precision, recall, F1-score, specificity, and log loss, models from Gradient Boosting, AdaBoost, Random Forest, k-nearest Neighbours, Support Vector Machine, and Decision Tree were assessed. Gradient Boosting performed best overall and had the highest accuracy (99.5%). Random Forest and AdaBoost also showed high classification accuracy. More features were beneficial for simpler models like k-Nearest Neighbours and Decision Tree. Random Forest and Gradient Boosting successfully decreased misclassification between related fault classes. The findings highlight the importance of selecting the appropriate models and features. Advanced feature engineering and parameter optimization could lead to further enhancements.
- 1 January 2025
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 53 (3) , 401-408
Open AccessWear fault diagnosis in journal bearings using vibration analysis and AI
In this study, machine learning models for identifying wear defects in journal bearings under various operating circumstances are compared. Healthy, low, and high wear states were simulated using an experimental test rig. Information Gain, Gain Ratio, Gini Index, and other feature selection techniques were used to analyze vibration signals from precision sensors. Relevance was used to rank features like Root Mean Square, Peak-to-Peak, and Peak. Using accuracy, precision, recall, F1-score, specificity, and log loss, models from Gradient Boosting, AdaBoost, Random Forest, k-nearest Neighbours, Support Vector Machine, and Decision Tree were assessed. Gradient Boosting performed best overall and had the highest accuracy (99.5%). Random Forest and AdaBoost also showed high classification accuracy. More features were beneficial for simpler models like k-Nearest Neighbours and Decision Tree. Random Forest and Gradient Boosting successfully decreased misclassification between related fault classes. The findings highlight the importance of selecting the appropriate models and features. Advanced feature engineering and parameter optimization could lead to further enhancements.
- 11 November 2024
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 87 (1) , 73-88
WASTE EGGSHELL AND SAWDUST AS REINFORCEMENTS FOR SUSTAINABLE POLYESTER COMPOSITES: MECHANICAL CHARACTERIZATION AND ENVIRONMENTAL DURABILITY ASSESSMENT
This research endeavor undertakes an experimental investigation into the bending and tensile properties of polyester composites reinforced with waste eggshell powder and sawdust particles at 35 wt.%. Valorizing these waste materials as reinforcements contributes to sustainable practices, waste minimization, and environmental pollution mitigation. Composite samples were fabricated using hand lay-up and compression molding techniques. The effects of environmental exposure to water, acidic, and basic media immersion on the mechanical performance were evaluated to assess durability. Experimental characterization through tensile and three-point bending tests determined mechanical properties, stress-strain behavior, and failure mechanisms. Additionally, finite element analysis (FEA) simulations complemented the experiments by providing insights into stress distributions, deformations, and potential failure initiation sites within the composites under flexural loading. The computational models accurately captured the reinforcing effects of the waste materials and the degradation induced by environmental exposure, validating the experimental trends. Incorporating waste natural fibers significantly enhanced polyester's bending strength by 140% (sawdust) and 75% (eggshell), and tensile strength by 13% (sawdust) and 10% (eggshell). However, environmental exposure degraded properties to varying extents, with water immersion reducing tensile strength by 63% (sawdust) and 3% (eggshell), and flexural strength by 63% (sawdust) and 3% (eggshell). The acidic medium caused 58% (sawdust) and 23% (eggshell) reductions in tensile strength, and similar flexural strength degradations. Strikingly, the basic medium decreased eggshell composite tensile strength by 170% and flexural strength by 6%, while sawdust composite strengths declined by 44%.
- 11 November 2024
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 87 (1) , 73-88
WASTE EGGSHELL AND SAWDUST AS REINFORCEMENTS FOR SUSTAINABLE POLYESTER COMPOSITES: MECHANICAL CHARACTERIZATION AND ENVIRONMENTAL DURABILITY ASSESSMENT
This research endeavor undertakes an experimental investigation into the bending and tensile properties of polyester composites reinforced with waste eggshell powder and sawdust particles at 35 wt.%. Valorizing these waste materials as reinforcements contributes to sustainable practices, waste minimization, and environmental pollution mitigation. Composite samples were fabricated using hand lay-up and compression molding techniques. The effects of environmental exposure to water, acidic, and basic media immersion on the mechanical performance were evaluated to assess durability. Experimental characterization through tensile and three-point bending tests determined mechanical properties, stress-strain behavior, and failure mechanisms. Additionally, finite element analysis (FEA) simulations complemented the experiments by providing insights into stress distributions, deformations, and potential failure initiation sites within the composites under flexural loading. The computational models accurately captured the reinforcing effects of the waste materials and the degradation induced by environmental exposure, validating the experimental trends. Incorporating waste natural fibers significantly enhanced polyester's bending strength by 140% (sawdust) and 75% (eggshell), and tensile strength by 13% (sawdust) and 10% (eggshell). However, environmental exposure degraded properties to varying extents, with water immersion reducing tensile strength by 63% (sawdust) and 3% (eggshell), and flexural strength by 63% (sawdust) and 3% (eggshell). The acidic medium caused 58% (sawdust) and 23% (eggshell) reductions in tensile strength, and similar flexural strength degradations. Strikingly, the basic medium decreased eggshell composite tensile strength by 170% and flexural strength by 6%, while sawdust composite strengths declined by 44%.
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2797 (1) , 090004
Investigation of various damping pads effect on vibration
Vibration damping pads are known as an absorber of mechanical energy to safeguard the overall system. The vibration source can be suppressed by using a vibratio
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2797 (1) , 090004
Open AccessInvestigation of various damping pads effect on vibration
Vibration damping pads are known as an absorber of mechanical energy to safeguard the overall system. The vibration source can be suppressed by using a vibratio