Du Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Du Wang has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Lianqing Zhu
Beijing Information Science and Technology University
9 shared publications - Mingli Dong
Key Laboratory of the Ministry of Education for Optoelectronic Measurement Technology and Instrument, Beijing Information Science and Technology University, Beijing, China
4 shared publications Yiqun Zhang
Civil Aviation Flight University of China
4 shared publications- Jingtao Xin
Key Laboratory of the Ministry of Education for Optoelectronic Measurement Technology and Instrument, Beijing Information Science & Technology University, Beijing, China
3 shared publications - Yunhong Zhu
Key Laboratory of the Ministry of Education for Optoelectronic Measurement Technology and Instrument, Beijing Information Science and Technology University, Beijing, China
3 shared publications Chaofan Deng
2 shared publications
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (19) , 28543-28552
Fabrication of Miniaturized and Lightweight Femtosecond FBG Sensor for Load Monitoring of Aircraft Landing Gear
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (19) , 28543-28552
Fabrication of Miniaturized and Lightweight Femtosecond FBG Sensor for Load Monitoring of Aircraft Landing Gear
- 1 August 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (16) , 24910-24925
A Multitask CNN-Transformer Network for Aircraft Structural Fatigue and Load Prediction Using FBG Sensors
- 1 August 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (16) , 24910-24925
A Multitask CNN-Transformer Network for Aircraft Structural Fatigue and Load Prediction Using FBG Sensors
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (13) , 5685-5692
Hundred-Channel, High-Speed, and Large-Capacity FBG Demodulation Based on an Amplified Tunable Laser
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (13) , 5685-5692
Hundred-Channel, High-Speed, and Large-Capacity FBG Demodulation Based on an Amplified Tunable Laser
- 17 November 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (24) , 49930-49943
Compact FBG strain sensor for an accurate measurement method with wide-range temperature compensation
Cross-sensitivity between strain and temperature is a thorny issue in fiber Bragg grating (FBG) sensing. Especially, due to the mismatch between the thermal expansion coefficients of the adhesive and the FBG, the effect of temperature is magnified even more when FBG strain is packaged with certain adhesives. To solve this problem, a specially designed strain sensor with wide-range temperature compensation is developed in this paper. The FBG strain sensor had a length of 18 mm and a weight of 0.35 g. Its sensitivity was calculated to be 1.35 pm/με, with excellent linearity (R 2 = 0.99951). Through experimental test and data analysis, the sensor demonstrated a temperature sensitivity of 29.8 pm/℃ within the -50 ℃ to 150 ℃ range, accompanied by a linear regression coefficient (R 2 ) of 0.9979, and maintained stable performance over thermal cycles. Post-compensation analysis revealed strain measurement accuracy exceeding 99% after temperature interference elimination. This sensor enables real-time thermal compensation for wing load monitoring, enhancing structural safety.
- 17 November 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (24) , 49930-49943
Compact FBG strain sensor for an accurate measurement method with wide-range temperature compensation
Cross-sensitivity between strain and temperature is a thorny issue in fiber Bragg grating (FBG) sensing. Especially, due to the mismatch between the thermal expansion coefficients of the adhesive and the FBG, the effect of temperature is magnified even more when FBG strain is packaged with certain adhesives. To solve this problem, a specially designed strain sensor with wide-range temperature compensation is developed in this paper. The FBG strain sensor had a length of 18 mm and a weight of 0.35 g. Its sensitivity was calculated to be 1.35 pm/με, with excellent linearity (R 2 = 0.99951). Through experimental test and data analysis, the sensor demonstrated a temperature sensitivity of 29.8 pm/℃ within the -50 ℃ to 150 ℃ range, accompanied by a linear regression coefficient (R 2 ) of 0.9979, and maintained stable performance over thermal cycles. Post-compensation analysis revealed strain measurement accuracy exceeding 99% after temperature interference elimination. This sensor enables real-time thermal compensation for wing load monitoring, enhancing structural safety.
- 14 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (24) , 11049-11057
Femtosecond Laser Fabrication of Apodized FBG via Synergistic Control of Pulse Energy – Adjustable Slit
This study proposes a synergistic control method combining energy modulation and adjustable slit manipulation for refractive index modulation (RIM) area apodization during femtosecond laser point-by-point (PbP) fabrication of high-quality apodized fiber Bragg gratings (AFBGs). We established an inverse coordination model between pulse energy and slit width to dynamically control the inscription area following Gaussian distribution, where higher pulse energy combined with narrower slit width creates longer inscription regions at the grating center, while lower energy with wider slit width produces shorter inscription regions at both grating ends. For experimental validation, we developed a femtosecond laser PbP collaborative inscription system. Results demonstrated a significant expansion of the single-pulse energy tuning range for PbP-FBG fabrication from 30 nJ to 150 nJ, effectively overcoming the key challenge of limited energy adjustability in PbP inscription. The fabricated 6-mm-long AFBG using polyimide-coated single-mode fiber exhibited remarkable performance characteristics: over 78% reflectivity and a side lobe suppression ratio (SLSR) exceeding 21.3 dB in the reflection spectrum. This approach provides enhanced flexibility for PbP-based fabrication of high-quality AFBGs, thereby substantially improving FBG performance.
- 14 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (24) , 11049-11057
Femtosecond Laser Fabrication of Apodized FBG via Synergistic Control of Pulse Energy – Adjustable Slit
This study proposes a synergistic control method combining energy modulation and adjustable slit manipulation for refractive index modulation (RIM) area apodization during femtosecond laser point-by-point (PbP) fabrication of high-quality apodized fiber Bragg gratings (AFBGs). We established an inverse coordination model between pulse energy and slit width to dynamically control the inscription area following Gaussian distribution, where higher pulse energy combined with narrower slit width creates longer inscription regions at the grating center, while lower energy with wider slit width produces shorter inscription regions at both grating ends. For experimental validation, we developed a femtosecond laser PbP collaborative inscription system. Results demonstrated a significant expansion of the single-pulse energy tuning range for PbP-FBG fabrication from 30 nJ to 150 nJ, effectively overcoming the key challenge of limited energy adjustability in PbP inscription. The fabricated 6-mm-long AFBG using polyimide-coated single-mode fiber exhibited remarkable performance characteristics: over 78% reflectivity and a side lobe suppression ratio (SLSR) exceeding 21.3 dB in the reflection spectrum. This approach provides enhanced flexibility for PbP-based fabrication of high-quality AFBGs, thereby substantially improving FBG performance.
- 22 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-11
A Tracking-Based High-Speed Demodulation Method for Fiber Bragg Grating Sensing System Based on Wavelength-Tunable Laser in Space Application
The vibration measurement of spacecraft structures in space applications has raised higher requirements for the demodulation frequency of the fiber Bragg grating (FBG) demodulator. In this article, a tracking-based high-speed demodulation method for FBG sensing system based on wavelength-tunable laser is proposed. The wavelength-tunable laser only scans wavelengths near the latest wavelength of each FBG sensor. The scanning range is constantly updated to achieve wavelength tracking, and the FBG demodulator continuously outputs the center wavelengths of the FBG sensors. The influence of multiple parameters on the demodulation frequency is simulated for the traditional full wavelength range scanning demodulation method and the proposed method. An FBG sensing system for measuring vibration was established. The demodulation frequencies are 14 Hz and 560 Hz when using these two methods, which coincides with the simulation results. The FBG sensing system can accurately measure vibration frequency below 200 Hz with a maximum error of 0.528 Hz. Thus, the proposed method significantly increases the demodulation frequency by 40 times compared to the traditional method and provides an effective approach to achieve highspeed demodulation of the FBG demodulator.
- 22 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-11
A Tracking-Based High-Speed Demodulation Method for Fiber Bragg Grating Sensing System Based on Wavelength-Tunable Laser in Space Application
The vibration measurement of spacecraft structures in space applications has raised higher requirements for the demodulation frequency of the fiber Bragg grating (FBG) demodulator. In this article, a tracking-based high-speed demodulation method for FBG sensing system based on wavelength-tunable laser is proposed. The wavelength-tunable laser only scans wavelengths near the latest wavelength of each FBG sensor. The scanning range is constantly updated to achieve wavelength tracking, and the FBG demodulator continuously outputs the center wavelengths of the FBG sensors. The influence of multiple parameters on the demodulation frequency is simulated for the traditional full wavelength range scanning demodulation method and the proposed method. An FBG sensing system for measuring vibration was established. The demodulation frequencies are 14 Hz and 560 Hz when using these two methods, which coincides with the simulation results. The FBG sensing system can accurately measure vibration frequency below 200 Hz with a maximum error of 0.528 Hz. Thus, the proposed method significantly increases the demodulation frequency by 40 times compared to the traditional method and provides an effective approach to achieve highspeed demodulation of the FBG demodulator.
- 22 January 2025
- Published by Elsevier in Optical Fiber Technology
- Vol. 90
Aircraft landing gear load prediction based on LSTM-KAN network
- 22 January 2025
- Published by Elsevier in Optical Fiber Technology
- Vol. 90
Aircraft landing gear load prediction based on LSTM-KAN network
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (3) , 4570-4581
Enhanced Load Prediction for Aircraft Landing Gear Utilizing Graph Convolutional Neural Network
This study presents an accurate aircraft landing gear load estimation model leveraging graph convolutional neural networks (GCN), which predicts loads from structural strain distribution data. A ground-based experimental system is established, deploying fiber grating strain sensors at key landing gear points to gather strain data under various operating conditions for model training. The GCN model undergoes strain-to-load mapping training and testing, with prediction accuracy and stability evaluated using maximum relative error, average relative error, and standard deviation. Results showcase stable and precise predictions, with X, Y, and Z load predictions achieving maximum relative errors of 5.18%, 4.15%, and 3.57%, respectively, and average relative errors of 1.58%, 0.61%, and 0.75%, respectively, alongside low standard deviations of 0.59N, 0.74N, and 0.46N. Comparative analyses against multiple linear regression and advanced neural networks (LSTM, CNN, MLP) underscore the GCN model’s superior prediction accuracy. This work holds significant potential for applications in aircraft structural health monitoring.
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (3) , 4570-4581
Enhanced Load Prediction for Aircraft Landing Gear Utilizing Graph Convolutional Neural Network
This study presents an accurate aircraft landing gear load estimation model leveraging graph convolutional neural networks (GCN), which predicts loads from structural strain distribution data. A ground-based experimental system is established, deploying fiber grating strain sensors at key landing gear points to gather strain data under various operating conditions for model training. The GCN model undergoes strain-to-load mapping training and testing, with prediction accuracy and stability evaluated using maximum relative error, average relative error, and standard deviation. Results showcase stable and precise predictions, with X, Y, and Z load predictions achieving maximum relative errors of 5.18%, 4.15%, and 3.57%, respectively, and average relative errors of 1.58%, 0.61%, and 0.75%, respectively, alongside low standard deviations of 0.59N, 0.74N, and 0.46N. Comparative analyses against multiple linear regression and advanced neural networks (LSTM, CNN, MLP) underscore the GCN model’s superior prediction accuracy. This work holds significant potential for applications in aircraft structural health monitoring.
- 3 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (22) , 36751-36760
Medium-High-Frequency and High Sensitivity Fiber Optic Acceleration Sensor Based on F–P Interference
high sensitivity fiber-optic acceleration sensor based on a Fabry-Perot Interferometer (FPI) formed by an aluminum alloy elastic mass-block structure is proposed for measuring acceleration signals in a vibrating environment. The sensing structure mainly consists of a single-mode optical fiber collimated reflector 1, reflector 2 and a mass block elastic structure, where the optical fiber collimated reflector 1 and the reflector 2 located on the upper surface of the elastic mass block form an F-P interferometric cavity. According to the F-P interferometric sensing principle, the reflectivity of the two end faces and the cavity length parameters are simulated and optimized to produce an acceleration sensor with a highly finesse reflectance spectrum (extremely narrow spectral trough). The mass block dimensions of the sensing structure were simulated and optimized and performance analyzed using finite element software, and the sensor was fabricated according to the analysis results, and the amplitude-frequency response, sensitivity characteristics and lateral anti-interference capability of the sensor were investigated experimentally. The experimental results show that the sensor has an intrinsic frequency of 2100 Hz, a sensitivity of 4.91 nm/g at 1300 Hz, a resolution of 0.204 mg, and a transverse immunity of less than 5% within the operating bandwidth of 0-1300 Hz. The sensor proposed in this paper is characterized by high sensitivity, a large operating bandwidth range, and low lateral interference, making it suitable for monitoring medium and high-frequency vibration signals in aerospace and other equipment structures.
- 3 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (22) , 36751-36760
Medium-High-Frequency and High Sensitivity Fiber Optic Acceleration Sensor Based on F–P Interference
high sensitivity fiber-optic acceleration sensor based on a Fabry-Perot Interferometer (FPI) formed by an aluminum alloy elastic mass-block structure is proposed for measuring acceleration signals in a vibrating environment. The sensing structure mainly consists of a single-mode optical fiber collimated reflector 1, reflector 2 and a mass block elastic structure, where the optical fiber collimated reflector 1 and the reflector 2 located on the upper surface of the elastic mass block form an F-P interferometric cavity. According to the F-P interferometric sensing principle, the reflectivity of the two end faces and the cavity length parameters are simulated and optimized to produce an acceleration sensor with a highly finesse reflectance spectrum (extremely narrow spectral trough). The mass block dimensions of the sensing structure were simulated and optimized and performance analyzed using finite element software, and the sensor was fabricated according to the analysis results, and the amplitude-frequency response, sensitivity characteristics and lateral anti-interference capability of the sensor were investigated experimentally. The experimental results show that the sensor has an intrinsic frequency of 2100 Hz, a sensitivity of 4.91 nm/g at 1300 Hz, a resolution of 0.204 mg, and a transverse immunity of less than 5% within the operating bandwidth of 0-1300 Hz. The sensor proposed in this paper is characterized by high sensitivity, a large operating bandwidth range, and low lateral interference, making it suitable for monitoring medium and high-frequency vibration signals in aerospace and other equipment structures.