Jingtao Xin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jingtao Xin has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
Jingjing Liao
7 shared publications- Chenbo Yu
Beijing Laboratory of Optical Fiber Sensing and System, Beijing Information Science and Technology University, Beijing, China
6 shared publications - Lianqing Zhu
Beijing Information Science and Technology University
6 shared publications - Du Wang
Beijing Information Science and Technology University
3 shared publications - Jingjing Liao
School of Optoelectronic Measurement Technology and Instrument, Beijing Information Science & Technology University, Beijing, China
2 shared publications - Mingli Dong
Key Laboratory of the Ministry of Education for Optoelectronic Measurement Technology and Instrument, Beijing Information Science and Technology University, Beijing, China
2 shared publications
Latest Publications
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (13) , 5685-5692
Hundred-Channel, High-Speed, and Large-Capacity FBG Demodulation Based on an Amplified Tunable Laser
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (13) , 5685-5692
Hundred-Channel, High-Speed, and Large-Capacity FBG Demodulation Based on an Amplified Tunable Laser
- 24 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (7) , 10058-10067
Research on a High-Sensitivity FBG Tilt Sensor With Vibration Suppression
To address the susceptibility of conventional fiber Bragg grating (FBG) tilt sensors to external vibrations and temperature interference, this paper proposes a high-sensitivity FBG tilt sensor with integrated vibration suppression. The sensor is based on a flexible hinge structure and employs a non-contact magnetic damping mechanism to enhance vibration resistance. Additionally, it achieves high sensitivity and temperature compensation through a self-differential compensation method. First, a theoretical model of the sensor is derived based on dynamic response equations. Then, static structural optimization is performed using finite element analysis (FEA) to determine the optimal structural parameters. A coupled magnetic-mechanical field simulation is also conducted to validate the feasibility of vibration suppression using the magnetic damping mechanism. Based on the optimized parameters, the sensor is fabricated and packaged, followed by comprehensive performance testing. Experimental results show that within a tilt range of ±5°, the sensor achieves a sensitivity of 248.4 pm/°, a linearity coefficient of 0.9993, and a repeatability error of less than 1.716%. The differential FBG configuration effectively eliminates temperature induced errors in tilt measurement. Furthermore, vibration tests confirm that the magnetic damping mechanism significantly reduces measurement errors caused by external random vibrations. In summary, the FBG tilt sensor proposed in this study achieves vibration suppression and temperature compensation while maintaining high tilt measurement sensitivity, thereby enhancing the environmental adaptability of the tilt sensor and broadening its application scenarios.
- 24 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (7) , 10058-10067
Research on a High-Sensitivity FBG Tilt Sensor With Vibration Suppression
To address the susceptibility of conventional fiber Bragg grating (FBG) tilt sensors to external vibrations and temperature interference, this paper proposes a high-sensitivity FBG tilt sensor with integrated vibration suppression. The sensor is based on a flexible hinge structure and employs a non-contact magnetic damping mechanism to enhance vibration resistance. Additionally, it achieves high sensitivity and temperature compensation through a self-differential compensation method. First, a theoretical model of the sensor is derived based on dynamic response equations. Then, static structural optimization is performed using finite element analysis (FEA) to determine the optimal structural parameters. A coupled magnetic-mechanical field simulation is also conducted to validate the feasibility of vibration suppression using the magnetic damping mechanism. Based on the optimized parameters, the sensor is fabricated and packaged, followed by comprehensive performance testing. Experimental results show that within a tilt range of ±5°, the sensor achieves a sensitivity of 248.4 pm/°, a linearity coefficient of 0.9993, and a repeatability error of less than 1.716%. The differential FBG configuration effectively eliminates temperature induced errors in tilt measurement. Furthermore, vibration tests confirm that the magnetic damping mechanism significantly reduces measurement errors caused by external random vibrations. In summary, the FBG tilt sensor proposed in this study achieves vibration suppression and temperature compensation while maintaining high tilt measurement sensitivity, thereby enhancing the environmental adaptability of the tilt sensor and broadening its application scenarios.
- 17 November 2025
- Published by Elsevier in Measurement
- Vol. 259
A monolithic mid-high frequency high-sensitivity 2D FBG vibration sensor
- 17 November 2025
- Published by Elsevier in Measurement
- Vol. 259
A monolithic mid-high frequency high-sensitivity 2D FBG vibration sensor
- 14 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (24) , 11049-11057
Femtosecond Laser Fabrication of Apodized FBG via Synergistic Control of Pulse Energy – Adjustable Slit
This study proposes a synergistic control method combining energy modulation and adjustable slit manipulation for refractive index modulation (RIM) area apodization during femtosecond laser point-by-point (PbP) fabrication of high-quality apodized fiber Bragg gratings (AFBGs). We established an inverse coordination model between pulse energy and slit width to dynamically control the inscription area following Gaussian distribution, where higher pulse energy combined with narrower slit width creates longer inscription regions at the grating center, while lower energy with wider slit width produces shorter inscription regions at both grating ends. For experimental validation, we developed a femtosecond laser PbP collaborative inscription system. Results demonstrated a significant expansion of the single-pulse energy tuning range for PbP-FBG fabrication from 30 nJ to 150 nJ, effectively overcoming the key challenge of limited energy adjustability in PbP inscription. The fabricated 6-mm-long AFBG using polyimide-coated single-mode fiber exhibited remarkable performance characteristics: over 78% reflectivity and a side lobe suppression ratio (SLSR) exceeding 21.3 dB in the reflection spectrum. This approach provides enhanced flexibility for PbP-based fabrication of high-quality AFBGs, thereby substantially improving FBG performance.
- 14 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (24) , 11049-11057
Femtosecond Laser Fabrication of Apodized FBG via Synergistic Control of Pulse Energy – Adjustable Slit
This study proposes a synergistic control method combining energy modulation and adjustable slit manipulation for refractive index modulation (RIM) area apodization during femtosecond laser point-by-point (PbP) fabrication of high-quality apodized fiber Bragg gratings (AFBGs). We established an inverse coordination model between pulse energy and slit width to dynamically control the inscription area following Gaussian distribution, where higher pulse energy combined with narrower slit width creates longer inscription regions at the grating center, while lower energy with wider slit width produces shorter inscription regions at both grating ends. For experimental validation, we developed a femtosecond laser PbP collaborative inscription system. Results demonstrated a significant expansion of the single-pulse energy tuning range for PbP-FBG fabrication from 30 nJ to 150 nJ, effectively overcoming the key challenge of limited energy adjustability in PbP inscription. The fabricated 6-mm-long AFBG using polyimide-coated single-mode fiber exhibited remarkable performance characteristics: over 78% reflectivity and a side lobe suppression ratio (SLSR) exceeding 21.3 dB in the reflection spectrum. This approach provides enhanced flexibility for PbP-based fabrication of high-quality AFBGs, thereby substantially improving FBG performance.
- 10 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (20) , 38820-38828
Research on High-Sensitivity Fiber Bragg Grating Pressure Sensor Based on Diaphragm–Lever Composite Structure
In order to meet the demand for high-sensitivity pressure detection, this paper proposes a design method for a fiber Bragg grating (FBG) pressure sensor based on a diaphragm-lever composite structure. By constructing a diaphragm deformation-lever displacement amplification mechanism, the pressure sensitivity of the sensor is effectively improved. Firstly, a theoretical model for the transmission of pressure signal-diaphragm deformation displacement-lever displacement amplification-FBG strain wavelength shift is established. The sensor sensitivity is theoretically analyzed through a geometric model, and it is concluded that the theoretical amplification ratio of the diaphragm-lever composite structure is 3.464, with a sensitivity of 84.101 nm/MPa. Then, SolidWorks is used for sensor design and modeling, and the Ansys simulation platform is employed for iterative optimization to determine structural parameters such as grating diameter and length. Finite element analysis is used to simulate and calculate the amplification ratio and sensitivity, yielding a simulated amplification ratio of 3.229 and a sensitivity of 78.091 nm/MPa. These results are highly consistent with the theoretical analysis, verifying the reliability of the theoretical model. Finally, a physical sensor is fabricated according to the optimized structure, and packaging and testing systems are built to complete the characteristic testing of the sensor. Experimental results show that within the range of 0-0.1 MPa, the amplification ratio of the diaphragm-lever composite structure is 2.841, and the pressure sensitivity is 69.042 nm/MPa, which are basically consistent with the theoretical and simulation results. The linearity is 99.9%, and the repeatability error and hysteresis error are 1.160% and 0.623%, respectively.
- 10 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (20) , 38820-38828
Research on High-Sensitivity Fiber Bragg Grating Pressure Sensor Based on Diaphragm–Lever Composite Structure
In order to meet the demand for high-sensitivity pressure detection, this paper proposes a design method for a fiber Bragg grating (FBG) pressure sensor based on a diaphragm-lever composite structure. By constructing a diaphragm deformation-lever displacement amplification mechanism, the pressure sensitivity of the sensor is effectively improved. Firstly, a theoretical model for the transmission of pressure signal-diaphragm deformation displacement-lever displacement amplification-FBG strain wavelength shift is established. The sensor sensitivity is theoretically analyzed through a geometric model, and it is concluded that the theoretical amplification ratio of the diaphragm-lever composite structure is 3.464, with a sensitivity of 84.101 nm/MPa. Then, SolidWorks is used for sensor design and modeling, and the Ansys simulation platform is employed for iterative optimization to determine structural parameters such as grating diameter and length. Finite element analysis is used to simulate and calculate the amplification ratio and sensitivity, yielding a simulated amplification ratio of 3.229 and a sensitivity of 78.091 nm/MPa. These results are highly consistent with the theoretical analysis, verifying the reliability of the theoretical model. Finally, a physical sensor is fabricated according to the optimized structure, and packaging and testing systems are built to complete the characteristic testing of the sensor. Experimental results show that within the range of 0-0.1 MPa, the amplification ratio of the diaphragm-lever composite structure is 2.841, and the pressure sensitivity is 69.042 nm/MPa, which are basically consistent with the theoretical and simulation results. The linearity is 99.9%, and the repeatability error and hysteresis error are 1.160% and 0.623%, respectively.
- 25 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-13
Development of a Compact Triaxial FBG Vibration Sensor for Medium-High Frequency Applications via Multiobjective Optimization Design
This study presents a miniature triaxial fiber Bragg grating (FBG) vibration sensor incorporating a novel elliptical guide-angle hybrid flexure hinge structure for stepper motor vibration monitoring. To tackle the multi-objective optimization challenges associated with sensor miniaturization and sensitivity enhancement, we developed a theoretical model and employed response surface methodology (RSM) combined with a multi-objective genetic algorithm (MOGA) for parametric optimization. The validity of the proposed design was verified by finite element analysis (FEA) using ANSYS, through modal and harmonic response simulations. The sensor comprises three orthogonal assembled identical modules, achieving high spatial efficiency with compact dimensions of 20×20×20 mm³ and a mass of 41.47 g. Ultra-short small-diameter FBGs were packaged using a dual-point encapsulation technique. Experimental results indicated that the sensor presented natural frequencies of 1570 Hz (X-axis), 1600 Hz (Y-axis), and 1620 Hz (Z-axis), with corresponding sensitivities reaching 67.34 pm/G, 65.61 pm/G, and 63.48 pm/G, respectively. The operational flat frequency range 20 - 1000 Hz, with the cross-axis interference in non-operational axes below 4% of the primary axis. Real-time triaxial vibration monitoring of a stepper motor under varying conditions confirmed the sensor’s reliability and consistency in multi-degree-of-freedom measurements. With its compact size, high sensitivity, broad frequency range, electromagnetic immunity, and multi-point deployment capability, this sensor is highly applicable for multi-axis medium-to-high frequency vibration measurements in confined spaces within aerospace and mechanical equipment applications.
- 25 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-13
Development of a Compact Triaxial FBG Vibration Sensor for Medium-High Frequency Applications via Multiobjective Optimization Design
This study presents a miniature triaxial fiber Bragg grating (FBG) vibration sensor incorporating a novel elliptical guide-angle hybrid flexure hinge structure for stepper motor vibration monitoring. To tackle the multi-objective optimization challenges associated with sensor miniaturization and sensitivity enhancement, we developed a theoretical model and employed response surface methodology (RSM) combined with a multi-objective genetic algorithm (MOGA) for parametric optimization. The validity of the proposed design was verified by finite element analysis (FEA) using ANSYS, through modal and harmonic response simulations. The sensor comprises three orthogonal assembled identical modules, achieving high spatial efficiency with compact dimensions of 20×20×20 mm³ and a mass of 41.47 g. Ultra-short small-diameter FBGs were packaged using a dual-point encapsulation technique. Experimental results indicated that the sensor presented natural frequencies of 1570 Hz (X-axis), 1600 Hz (Y-axis), and 1620 Hz (Z-axis), with corresponding sensitivities reaching 67.34 pm/G, 65.61 pm/G, and 63.48 pm/G, respectively. The operational flat frequency range 20 - 1000 Hz, with the cross-axis interference in non-operational axes below 4% of the primary axis. Real-time triaxial vibration monitoring of a stepper motor under varying conditions confirmed the sensor’s reliability and consistency in multi-degree-of-freedom measurements. With its compact size, high sensitivity, broad frequency range, electromagnetic immunity, and multi-point deployment capability, this sensor is highly applicable for multi-axis medium-to-high frequency vibration measurements in confined spaces within aerospace and mechanical equipment applications.
- 31 May 2025
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 193
Research on tunable laser power amplification for fiber grating sensing demodulation
- 31 May 2025
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 193
Research on tunable laser power amplification for fiber grating sensing demodulation
- 1 April 2025
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 64 (04) , 044104-11
High-precision real-time wavelength self-calibration for optical spectrum analyzer based on F-P etalon
To solve the repeatability deviations in optical spectrum analyzers (OSA) due to mechanical scanning errors and scan spacing variations during long-term measurements, we propose a real-time wavelength self-calibration method for OSA based on a Fabry-Perot etalon (F-P etalon). Different from traditional calibration methods that require all F-P reflection peaks, this method uses two high-reflectivity fiber Bragg gratings (FBGs) to filter the F-P spectrum, selecting only the two reflection peaks at one head and one tail of the C+L band to construct a reference spectrum. The reference spectrum is cascaded with the general FBG signal and transmitted through the OSA channel. The OSA is calibrated by monitoring changes in the reference spectrum during each scan and outputting the calibrated FBG wavelength value in real time through data processing, thereby achieving real-time wavelength self-calibration while maintaining stability during long-term measurements. The real-time wavelength self-calibration system was developed and tested over an extended period. The experimental results show that calibration reduced the maximum wavelength shift from 12.8 to 3.4 pm (26.5% of the original) and maintained stability over time, as well as reduced the shift dispersion from 2.38 to 0.75 pm (31.5% of the original). The calibration system significantly improved the long-term stability and measurement accuracy of the OSA. This research enhances the application of OSA in FBG sensors and shows promise for broader applications, including optical demodulation.
- 1 April 2025
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 64 (04) , 044104-11
High-precision real-time wavelength self-calibration for optical spectrum analyzer based on F-P etalon
To solve the repeatability deviations in optical spectrum analyzers (OSA) due to mechanical scanning errors and scan spacing variations during long-term measurements, we propose a real-time wavelength self-calibration method for OSA based on a Fabry-Perot etalon (F-P etalon). Different from traditional calibration methods that require all F-P reflection peaks, this method uses two high-reflectivity fiber Bragg gratings (FBGs) to filter the F-P spectrum, selecting only the two reflection peaks at one head and one tail of the C+L band to construct a reference spectrum. The reference spectrum is cascaded with the general FBG signal and transmitted through the OSA channel. The OSA is calibrated by monitoring changes in the reference spectrum during each scan and outputting the calibrated FBG wavelength value in real time through data processing, thereby achieving real-time wavelength self-calibration while maintaining stability during long-term measurements. The real-time wavelength self-calibration system was developed and tested over an extended period. The experimental results show that calibration reduced the maximum wavelength shift from 12.8 to 3.4 pm (26.5% of the original) and maintained stability over time, as well as reduced the shift dispersion from 2.38 to 0.75 pm (31.5% of the original). The calibration system significantly improved the long-term stability and measurement accuracy of the OSA. This research enhances the application of OSA in FBG sensors and shows promise for broader applications, including optical demodulation.