Luigi Lodato
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Luigi Lodato has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Costanza
Istituto Nazionale di Geofisica e Vulcanologia (INGV), Sezione Osservatorio Etneo, Catania, Italy
2 shared publications - Claudio Martino
Osservatorio Vesuviano, Istituto Nazionale di Geofisica e Vulcanologia, Rome, Italy, Italy
2 shared publications - Daniele Storni
Wise Robotics, 00131 Roma, Italy
2 shared publications - Domenico Patanè
Osservatorio Etneo - Sezione di Catania, Istituto Nazionale di Geofisica e Vulcanologia, Rome, Italy, Italy
2 shared publications - Francesco Lo Iacono
University of Enna “Kore
2 shared publications - Giacomo Navarra
University of Enna “Kore
2 shared publications
Latest Publications
- Open Access
- 30 September 2026
- Published by MDPI AG in Remote Sensing
- Vol. 18 (19) , 3348
Ground-Based Camera Network at Active Sicilian Volcanoes: Technical Improvements and Real-Time Extraction of Eruptive Parameters
Video surveillance systems are well-established tools for monitoring eruptive phenomena at active volcanoes. Consequently, video records have become a primary source of data for describing and quantifying volcanic activity worldwide. Prominent examples include the Sicilian volcanoes (Etna, Stromboli, and Vulcano), which are among the most active and closely monitored globally. The increasingly widespread use of thermal and high-definition visible cameras provides insights into eruptive processes and their evolution. In this study, we detail 32 years of technological evolution of the camera surveillance network installed on Sicilian volcanoes. We demonstrate how dedicated, in-house software tools for real-time image analysis enable the detection and identification of eruptive scenarios. Furthermore, these systems allow for the quantification of key physical parameters, including explosion intensity at Stromboli, mass eruption rate and column height during lava fountains at Etna, and variations in fumarolic activity at Vulcano. Additionally, visual and thermal imagery allows volcanologists to issue timely and effective warnings to the Italian Department of Civil Protection, as well as regional and international authorities. Overall, these results highlight the substantial advantages of continuous video monitoring infrastructure for real-time volcanic hazard assessment and risk mitigation.
- 30 September 2026
- Published by MDPI AG in Remote Sensing
- Vol. 18 (19) , 3348
Open AccessGround-Based Camera Network at Active Sicilian Volcanoes: Technical Improvements and Real-Time Extraction of Eruptive Parameters
Video surveillance systems are well-established tools for monitoring eruptive phenomena at active volcanoes. Consequently, video records have become a primary source of data for describing and quantifying volcanic activity worldwide. Prominent examples include the Sicilian volcanoes (Etna, Stromboli, and Vulcano), which are among the most active and closely monitored globally. The increasingly widespread use of thermal and high-definition visible cameras provides insights into eruptive processes and their evolution. In this study, we detail 32 years of technological evolution of the camera surveillance network installed on Sicilian volcanoes. We demonstrate how dedicated, in-house software tools for real-time image analysis enable the detection and identification of eruptive scenarios. Furthermore, these systems allow for the quantification of key physical parameters, including explosion intensity at Stromboli, mass eruption rate and column height during lava fountains at Etna, and variations in fumarolic activity at Vulcano. Additionally, visual and thermal imagery allows volcanologists to issue timely and effective warnings to the Italian Department of Civil Protection, as well as regional and international authorities. Overall, these results highlight the substantial advantages of continuous video monitoring infrastructure for real-time volcanic hazard assessment and risk mitigation.
- Open Access
- 14 February 2026
- Published by MDPI AG in Remote Sensing
- Vol. 18 (4) , 601
Exploitation of Multi-Sensor UAS Surveying for Monitoring the Volcanic Unrest at Vulcano Island (September 2021–June 2024)
In September 2021, significant changes in the geophysical and geochemical parameters on Vulcano Island were recorded by the surveillance network activities and periodic surveys. Between October 2021 and June 2024, additional surveys were conducted to acquire LIDAR, thermal, and RGB datasets for the generation of Digital Terrain Models (DTMs), orthophotos, and fumarole field maps. These data were collected using DJI Matrice 300 UAS platforms. Precision positioning was ensured through a POS/NAV RTK georeferencing approach. The instrumentation included Genius R-Fans-16 and DJI Zenmuse L1 laser scanners for structural mapping, alongside Zenmuse H20T infrared cameras for the thermal detection of potential instabilities on the volcano flanks, focused on the northern area and summit of Gran Cratere La Fossa, and these were subsequently repeated in May 2022, October 2022, October 2023, and June 2024. Additionally, 3D reconstruction targeted morphological variations in unstable areas like the cone top, Forgia Vecchia, and the 1988 landslide site. In May 2022, anomalous degassing in the Eastern Bay led to increased gas and hydrothermal fluid emissions, causing water whitening in front of Baia di Levante. Optical-thermal monitoring, both on land and at sea, detected multiple hydrothermal gas streams, aiding in assessing the magnitude and areal extension of fumarolic fields. These findings contribute to establishing a comprehensive monitoring approach for understanding the volcanic unrest evolution cost-effectively and safely.
- 14 February 2026
- Published by MDPI AG in Remote Sensing
- Vol. 18 (4) , 601
Open AccessExploitation of Multi-Sensor UAS Surveying for Monitoring the Volcanic Unrest at Vulcano Island (September 2021–June 2024)
In September 2021, significant changes in the geophysical and geochemical parameters on Vulcano Island were recorded by the surveillance network activities and periodic surveys. Between October 2021 and June 2024, additional surveys were conducted to acquire LIDAR, thermal, and RGB datasets for the generation of Digital Terrain Models (DTMs), orthophotos, and fumarole field maps. These data were collected using DJI Matrice 300 UAS platforms. Precision positioning was ensured through a POS/NAV RTK georeferencing approach. The instrumentation included Genius R-Fans-16 and DJI Zenmuse L1 laser scanners for structural mapping, alongside Zenmuse H20T infrared cameras for the thermal detection of potential instabilities on the volcano flanks, focused on the northern area and summit of Gran Cratere La Fossa, and these were subsequently repeated in May 2022, October 2022, October 2023, and June 2024. Additionally, 3D reconstruction targeted morphological variations in unstable areas like the cone top, Forgia Vecchia, and the 1988 landslide site. In May 2022, anomalous degassing in the Eastern Bay led to increased gas and hydrothermal fluid emissions, causing water whitening in front of Baia di Levante. Optical-thermal monitoring, both on land and at sea, detected multiple hydrothermal gas streams, aiding in assessing the magnitude and areal extension of fumarolic fields. These findings contribute to establishing a comprehensive monitoring approach for understanding the volcanic unrest evolution cost-effectively and safely.
- Open Access
Shake Table Tests on Scaled Masonry Building: Comparison of Performance of Various Micro-Electromechanical System Accelerometers (MEMS) for Structural Health Monitoring
This study presents the results of an experimental investigation conducted on a 2:3 scale model of a two-story stone masonry building. We tested the model on the UniKORE L.E.D.A. lab shake table, simulating the Mw 6.3 earthquake ground motion that struck L’Aquila, Italy, on 6 April 2009, with progressively increasing peak acceleration levels. We installed a network of accelerometric sensors on the model to capture its structural behaviour under seismic excitation. Medium-to lower-cost MEMS accelerometers (classes A and B) were compared with traditional piezoelectric sensors commonly used in Structural Health Monitoring (SHM). The experiment assessed the structural performance and damage progression of masonry buildings subjected to realistic earthquake inputs. Additionally, the collected data provided valuable insights into the effectiveness of different sensor types and configurations in detecting key vibrational and failure patterns. All the sensors were able to accurately measure the dynamic response during seismic excitation. However, not all of them were suitable for Operational Modal Analysis (OMA) in noisy environments, where their self-noise represents a crucial factor. This suggests that the self-noise of MEMS accelerometers must be less than 1 µg/√Hz, or preferably below 0.5 µg/√Hz, to obtain good results from the OMA. Therefore, we recommend ultra-low-noise sensors for detecting differences in the structural behaviour before and after seismic events. Our findings provide valuable insights into the seismic vulnerability of masonry structures and the effectiveness of sensors in detecting damage. The management of buildings in earthquake-prone areas can benefit from these specifications.
Open AccessShake Table Tests on Scaled Masonry Building: Comparison of Performance of Various Micro-Electromechanical System Accelerometers (MEMS) for Structural Health Monitoring
This study presents the results of an experimental investigation conducted on a 2:3 scale model of a two-story stone masonry building. We tested the model on the UniKORE L.E.D.A. lab shake table, simulating the Mw 6.3 earthquake ground motion that struck L’Aquila, Italy, on 6 April 2009, with progressively increasing peak acceleration levels. We installed a network of accelerometric sensors on the model to capture its structural behaviour under seismic excitation. Medium-to lower-cost MEMS accelerometers (classes A and B) were compared with traditional piezoelectric sensors commonly used in Structural Health Monitoring (SHM). The experiment assessed the structural performance and damage progression of masonry buildings subjected to realistic earthquake inputs. Additionally, the collected data provided valuable insights into the effectiveness of different sensor types and configurations in detecting key vibrational and failure patterns. All the sensors were able to accurately measure the dynamic response during seismic excitation. However, not all of them were suitable for Operational Modal Analysis (OMA) in noisy environments, where their self-noise represents a crucial factor. This suggests that the self-noise of MEMS accelerometers must be less than 1 µg/√Hz, or preferably below 0.5 µg/√Hz, to obtain good results from the OMA. Therefore, we recommend ultra-low-noise sensors for detecting differences in the structural behaviour before and after seismic events. Our findings provide valuable insights into the seismic vulnerability of masonry structures and the effectiveness of sensors in detecting damage. The management of buildings in earthquake-prone areas can benefit from these specifications.
- Open Access
- 19 December 2024
- Published by MDPI AG in Preprints.org
Shake Table Tests on a Scaled Masonry Building: Performance Comparison of Various MEMS Accelerometers for SHM
This study presents the results of an experimental investigation conducted on a 2:3 scale model of a two-storey stone masonry building. We tested the model on the UniKORE L.E.D.A. lab shake table, simulating the Mw 6.3 earthquake ground motion that struck L’Aquila, Italy, on April 06, 2009, with progressively increasing peak acceleration levels. We installed a network of accelerometric sensors on the model to capture its structural behaviour under seismic excitation. Medium- to lower-cost MEMS accelerometers (Classes A and B) were compared with traditional piezoelectric sensors commonly used in Structural Health Monitoring (SHM). The experiment assessed the structural performance and damage progression of masonry buildings subjected to realistic earthquake inputs. Additionally, the collected data provided valuable insights into the effectiveness of different sensor types and configurations in detecting key vibrational and failure patterns. All the sensors were able to accurately measure the dynamic response during seismic excitation. However, not all of them were suitable for Operational Modal Analysis (OMA) in noisy environments, where their self-noise represents a crucial factor. This suggests that the self-noise of the MEMS accelerometers must be less than 1 µg/√Hz, or preferably below 0.5 µg/√Hz, to obtain good results from the OMA analysis. Therefore, we recommend ultra-low-noise sensors for detecting differences in structural behaviour before and after seismic events. Our findings provide valuable insights into the seismic vulnerability of masonry structures and effectiveness of sensors in detecting damage. The management of buildings in earthquake-prone areas can benefit from these specifications.
- 19 December 2024
- Published by MDPI AG in Preprints.org
Open AccessShake Table Tests on a Scaled Masonry Building: Performance Comparison of Various MEMS Accelerometers for SHM
This study presents the results of an experimental investigation conducted on a 2:3 scale model of a two-storey stone masonry building. We tested the model on the UniKORE L.E.D.A. lab shake table, simulating the Mw 6.3 earthquake ground motion that struck L’Aquila, Italy, on April 06, 2009, with progressively increasing peak acceleration levels. We installed a network of accelerometric sensors on the model to capture its structural behaviour under seismic excitation. Medium- to lower-cost MEMS accelerometers (Classes A and B) were compared with traditional piezoelectric sensors commonly used in Structural Health Monitoring (SHM). The experiment assessed the structural performance and damage progression of masonry buildings subjected to realistic earthquake inputs. Additionally, the collected data provided valuable insights into the effectiveness of different sensor types and configurations in detecting key vibrational and failure patterns. All the sensors were able to accurately measure the dynamic response during seismic excitation. However, not all of them were suitable for Operational Modal Analysis (OMA) in noisy environments, where their self-noise represents a crucial factor. This suggests that the self-noise of the MEMS accelerometers must be less than 1 µg/√Hz, or preferably below 0.5 µg/√Hz, to obtain good results from the OMA analysis. Therefore, we recommend ultra-low-noise sensors for detecting differences in structural behaviour before and after seismic events. Our findings provide valuable insights into the seismic vulnerability of masonry structures and effectiveness of sensors in detecting damage. The management of buildings in earthquake-prone areas can benefit from these specifications.