Huirong Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Huirong Huang has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
- Qian Huang
School of Petroleum Engineering, Chongqing University of Science and Technology, Chongqing 401331, China
11 shared publications - Xueyuan Long
School of Petroleum Engineering, Chongqing University of Science and Technology, Chongqing 401331, China
8 shared publications - Yuan Tian
College of Petroleum and Natural Gas Engineering, Chongqing University of Science and Technology, Chongqing 401331, China
8 shared publications - Jie Zhong
School of Petroleum Engineering, Chongqing University of Science and Technology, Chongqing 401331, China
4 shared publications - Jing Gong
National Engineering Laboratory for Pipeline Safety, China University of Petroleum, Beijing, China
4 shared publications - Yuan Tian
College of Petroleum and Natural Gas Engineering, Chongqing University of Science and Technology, Chongqing 401331, China
4 shared publications
Latest Publications
- Open Access
Gas–Solid Two-Phase Flow Characteristics and Separation Performance of a Cyclone Desander
Balancing separation efficiency and pressure loss is essential for sand removal at shale gas wellheads. A double-cone cyclone desander was investigated using numerical simulations coupling a Reynolds stress model with a discrete phase model, single-factor analysis, and an orthogonal design. Structural and operating parameters were evaluated, and field performance was compared across two 161-day operating periods before and after optimization. At an inlet velocity of 5 m/s, a particle-size range of 0.02–0.10 mm, and a particle mass flow rate of 0.26 kg/s, the selected configuration achieved a simulated separation efficiency of 87.0%, increasing by 17.5 percentage points over the initial configuration. Pressure drop remained nearly unchanged, from 934.4 to 928.4 Pa, while overall height decreased by 129 mm. Increasing inlet velocity reduced separation efficiency and increased pressure drop. Shifting the size range toward larger particles improved capture with little effect on pressure drop. Field desanding efficiency increased by 34.84–35.70 percentage points across corresponding stages; however, the nonconcurrent comparison cannot isolate the contribution of optimization. Structural optimization can therefore improve simulated separation performance with nearly unchanged pressure drop, whereas selecting operating velocity requires balancing throughput and separation efficiency.
Open AccessGas–Solid Two-Phase Flow Characteristics and Separation Performance of a Cyclone Desander
Balancing separation efficiency and pressure loss is essential for sand removal at shale gas wellheads. A double-cone cyclone desander was investigated using numerical simulations coupling a Reynolds stress model with a discrete phase model, single-factor analysis, and an orthogonal design. Structural and operating parameters were evaluated, and field performance was compared across two 161-day operating periods before and after optimization. At an inlet velocity of 5 m/s, a particle-size range of 0.02–0.10 mm, and a particle mass flow rate of 0.26 kg/s, the selected configuration achieved a simulated separation efficiency of 87.0%, increasing by 17.5 percentage points over the initial configuration. Pressure drop remained nearly unchanged, from 934.4 to 928.4 Pa, while overall height decreased by 129 mm. Increasing inlet velocity reduced separation efficiency and increased pressure drop. Shifting the size range toward larger particles improved capture with little effect on pressure drop. Field desanding efficiency increased by 34.84–35.70 percentage points across corresponding stages; however, the nonconcurrent comparison cannot isolate the contribution of optimization. Structural optimization can therefore improve simulated separation performance with nearly unchanged pressure drop, whereas selecting operating velocity requires balancing throughput and separation efficiency.
- Open Access
Research on Reliability Calculation Model for Pipeline Units Integrating Data and Mechanism
Accurate reliability assessment of pipeline units remains challenging due to complex degradation processes and multiple sources of uncertainty. To address this issue, this paper proposes a dynamic reliability assessment model that integrates historical failure data with mechanistic principles. To overcome the computational bottleneck of conventional reliability models in handling high-dimensional complex integrals, Bayesian theory is adopted. The prior distribution, derived from expert knowledge or general empirical laws, is rigorously coupled with the likelihood function of historical failure data to construct a hierarchical parameter inference framework. For accurate parameter estimation, Markov Chain Monte Carlo (MCMC) simulation is carried out within the OpenBUGS environment, and the Brooks–Gelman–Rubin (BGR) diagnostic criterion is employed to ensure convergence and statistical validity of the computed results. The case study indicates that the integration of historical failure data effectively adjusts the expected failure time (μ) and the degree of dispersion (σ), substantially narrows the 95% confidence intervals, and reduces prediction uncertainty. The updated failure probability curve shows a clear leftward shift relative to the theoretical prediction. Based on these findings, it is recommended that the key maintenance phase be advanced from the 15th year to the 12th year, thereby achieving an optimal balance between operational safety and cost-effectiveness.
Open AccessResearch on Reliability Calculation Model for Pipeline Units Integrating Data and Mechanism
Accurate reliability assessment of pipeline units remains challenging due to complex degradation processes and multiple sources of uncertainty. To address this issue, this paper proposes a dynamic reliability assessment model that integrates historical failure data with mechanistic principles. To overcome the computational bottleneck of conventional reliability models in handling high-dimensional complex integrals, Bayesian theory is adopted. The prior distribution, derived from expert knowledge or general empirical laws, is rigorously coupled with the likelihood function of historical failure data to construct a hierarchical parameter inference framework. For accurate parameter estimation, Markov Chain Monte Carlo (MCMC) simulation is carried out within the OpenBUGS environment, and the Brooks–Gelman–Rubin (BGR) diagnostic criterion is employed to ensure convergence and statistical validity of the computed results. The case study indicates that the integration of historical failure data effectively adjusts the expected failure time (μ) and the degree of dispersion (σ), substantially narrows the 95% confidence intervals, and reduces prediction uncertainty. The updated failure probability curve shows a clear leftward shift relative to the theoretical prediction. Based on these findings, it is recommended that the key maintenance phase be advanced from the 15th year to the 12th year, thereby achieving an optimal balance between operational safety and cost-effectiveness.
- Open Access
- 8 October 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (19) , 9954
Thermomechanical Stress Response of Mechanically Lined Pipes Under Combined Loading
Mechanically lined pipes (MLP) combine a carbon-steel base pipe with a thin corrosion-resistant liner that transfers load through frictional contact. This numerical study compares the stress responses of matched monometallic and mechanically lined pipes under prescribed internal pressure, temperature, and bending. Three-dimensional finite element models are used to represent the material layers, contact, friction, and thermal loading. Circumferential mesh refinement and comparison with field inspection data provide checks on the reported stress response. In the non-bending one-factor cases, pressure and diameter primarily affect equivalent stress, whereas increasing temperature increases liner compression and base-pipe equivalent stress. At constant total wall thickness, increasing liner thickness reduces liner compression but increases stress in the thinner base pipe. Bending increases both response measures. Local sensitivity and two-factor analyses characterize stress variations within the sampled conditions. Exploratory regression equations show high internal cross-validation accuracy, and on 22 finite-element cases, the unchanged regression equations achieved R2 values of 0.965 for liner stress and 0.986 for base-pipe stress. These results support stress-trend estimation within the tested conditions but do not establish accuracy for arbitrary five-factor combinations or a universal failure threshold.
- 8 October 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (19) , 9954
Open AccessThermomechanical Stress Response of Mechanically Lined Pipes Under Combined Loading
Mechanically lined pipes (MLP) combine a carbon-steel base pipe with a thin corrosion-resistant liner that transfers load through frictional contact. This numerical study compares the stress responses of matched monometallic and mechanically lined pipes under prescribed internal pressure, temperature, and bending. Three-dimensional finite element models are used to represent the material layers, contact, friction, and thermal loading. Circumferential mesh refinement and comparison with field inspection data provide checks on the reported stress response. In the non-bending one-factor cases, pressure and diameter primarily affect equivalent stress, whereas increasing temperature increases liner compression and base-pipe equivalent stress. At constant total wall thickness, increasing liner thickness reduces liner compression but increases stress in the thinner base pipe. Bending increases both response measures. Local sensitivity and two-factor analyses characterize stress variations within the sampled conditions. Exploratory regression equations show high internal cross-validation accuracy, and on 22 finite-element cases, the unchanged regression equations achieved R2 values of 0.965 for liner stress and 0.986 for base-pipe stress. These results support stress-trend estimation within the tested conditions but do not establish accuracy for arbitrary five-factor combinations or a universal failure threshold.
- Open Access
Analysis of Interlayer Stress Transfer Mechanism of Bimetallic Composite Pipes
Addressing the ill-defined interlayer stress transfer mechanisms and the risk of stress exceeding material limits in bimetallic composite pipes under landslide hazards in high-steep mountainous regions, this study establishes a refined pipe–soil interaction finite element (FE) framework. Built upon a previously validated coupled model, interlayer interfacial contact formulations were enhanced, and valid operating regimes were systematically screened using the ultimate tensile strength (UTS) as the structural failure criterion. The regulatory impacts of soil displacement, internal operating pressure, and base pipe wall thickness on interlayer stress transfer efficiency were quantitatively mapped. The results demonstrate that within the valid service window, the interlayer stress transfer coefficient continuously escalates with soil displacement, identifying 3 m as the critical displacement threshold for base pipe yielding. Elevating internal pressure increases the stress transfer coefficient, which is mainly dominated by the high sensitivity of the thin liner’s membrane stress to internal pressure, and is secondarily promoted by the enhancement of interfacial shear capacity caused by increased contact pressure. Crucially, increasing the base pipe wall thickness from 12 mm to 15 mm effectively reduces the peak stress of the base pipe from 440.5 MPa to 310.2 MPa within the safe operational regime (1 m displacement) while systematically lowering the interlayer stress transfer coefficient η from 0.84 to 0.78 at the 3 m critical yielding threshold. This structural shielding effect is fundamentally driven by the enhanced structural stiffness (flexural rigidity) of the outer base pipe, which directly absorbs the primary geotechnical bending load and consequently lowers the deformation demand transmitted across the interface. Ultimately, this work unveils the core interlayer transfer mechanism characterized by “base-pipe stiffness dominance, interfacial shear transmission, elastic modulus mismatch governing stress allocation, and deformation compatibility steering load pathways,” providing a robust theoretical foundation for the interfacial integrity design of bimetallic composite pipelines in landslide-prone mountainous environments.
Open AccessAnalysis of Interlayer Stress Transfer Mechanism of Bimetallic Composite Pipes
Addressing the ill-defined interlayer stress transfer mechanisms and the risk of stress exceeding material limits in bimetallic composite pipes under landslide hazards in high-steep mountainous regions, this study establishes a refined pipe–soil interaction finite element (FE) framework. Built upon a previously validated coupled model, interlayer interfacial contact formulations were enhanced, and valid operating regimes were systematically screened using the ultimate tensile strength (UTS) as the structural failure criterion. The regulatory impacts of soil displacement, internal operating pressure, and base pipe wall thickness on interlayer stress transfer efficiency were quantitatively mapped. The results demonstrate that within the valid service window, the interlayer stress transfer coefficient continuously escalates with soil displacement, identifying 3 m as the critical displacement threshold for base pipe yielding. Elevating internal pressure increases the stress transfer coefficient, which is mainly dominated by the high sensitivity of the thin liner’s membrane stress to internal pressure, and is secondarily promoted by the enhancement of interfacial shear capacity caused by increased contact pressure. Crucially, increasing the base pipe wall thickness from 12 mm to 15 mm effectively reduces the peak stress of the base pipe from 440.5 MPa to 310.2 MPa within the safe operational regime (1 m displacement) while systematically lowering the interlayer stress transfer coefficient η from 0.84 to 0.78 at the 3 m critical yielding threshold. This structural shielding effect is fundamentally driven by the enhanced structural stiffness (flexural rigidity) of the outer base pipe, which directly absorbs the primary geotechnical bending load and consequently lowers the deformation demand transmitted across the interface. Ultimately, this work unveils the core interlayer transfer mechanism characterized by “base-pipe stiffness dominance, interfacial shear transmission, elastic modulus mismatch governing stress allocation, and deformation compatibility steering load pathways,” providing a robust theoretical foundation for the interfacial integrity design of bimetallic composite pipelines in landslide-prone mountainous environments.
- Open Access
Study on Erosion Patterns of Cyclone Desanders at Shale Gas Wellheads
In shale gas extraction, solid particles such as fracturing proppants cause erosion in production and transmission pipelines. Cyclone desanders are widely used for gas–solid separation, but high-velocity sand-laden fluids frequently induce equipment failure, leakage and safety risks. Therefore, research on erosion and protective measures is essential. This study focuses on the desander at the M shale gas wellhead, where wall thickness was measured at three monitoring points to determine erosion rates. A CFD-based numerical erosion model for the cyclone desander was developed using ANSYS Fluent within the ANSYS Workbench 19.2 environment (ANSYS, Inc., Canonsburg, PA, USA). The model was validated by comparing simulation results with field data, revealing the distribution patterns of the velocity field, pressure field, and erosion rate. The study analyzed the impact of nine factors on desander erosion: inlet aspect ratio, cylinder radius, cone length, dust discharge port diameter, exhaust port diameter, particle size, particle concentration, inlet velocity, and operating pressure, clarifying the erosion variation patterns for each factor. SPSSAU V25.0 (Beijing Qingsi Technology Co., Ltd., Beijing, China) was employed to analyze the significance of these nine factors, identifying six significant influencing factors: inlet aspect ratio, cylinder diameter, dust discharge port diameter, particle size, particle concentration, and inlet velocity. Subsequently, response surface analysis was performed using Design-Expert 13 (Stat-Ease, Inc., Minneapolis, MN, USA) to obtain the relationship between the factors and their impact on maximum erosion, leading to the establishment of a predictive model for the maximum erosion rate. In addition, geometry optimization, local wall thickening, coating protection, material selection, and bionic rib structures were discussed as erosion-mitigation strategies. The optimized geometry reduced the erosion rate at the inlet and dust discharge outlet by 20.4% and 21.8%, respectively, while the bionic rib structure reduced the maximum erosion rate by 58%.
Open AccessStudy on Erosion Patterns of Cyclone Desanders at Shale Gas Wellheads
In shale gas extraction, solid particles such as fracturing proppants cause erosion in production and transmission pipelines. Cyclone desanders are widely used for gas–solid separation, but high-velocity sand-laden fluids frequently induce equipment failure, leakage and safety risks. Therefore, research on erosion and protective measures is essential. This study focuses on the desander at the M shale gas wellhead, where wall thickness was measured at three monitoring points to determine erosion rates. A CFD-based numerical erosion model for the cyclone desander was developed using ANSYS Fluent within the ANSYS Workbench 19.2 environment (ANSYS, Inc., Canonsburg, PA, USA). The model was validated by comparing simulation results with field data, revealing the distribution patterns of the velocity field, pressure field, and erosion rate. The study analyzed the impact of nine factors on desander erosion: inlet aspect ratio, cylinder radius, cone length, dust discharge port diameter, exhaust port diameter, particle size, particle concentration, inlet velocity, and operating pressure, clarifying the erosion variation patterns for each factor. SPSSAU V25.0 (Beijing Qingsi Technology Co., Ltd., Beijing, China) was employed to analyze the significance of these nine factors, identifying six significant influencing factors: inlet aspect ratio, cylinder diameter, dust discharge port diameter, particle size, particle concentration, and inlet velocity. Subsequently, response surface analysis was performed using Design-Expert 13 (Stat-Ease, Inc., Minneapolis, MN, USA) to obtain the relationship between the factors and their impact on maximum erosion, leading to the establishment of a predictive model for the maximum erosion rate. In addition, geometry optimization, local wall thickening, coating protection, material selection, and bionic rib structures were discussed as erosion-mitigation strategies. The optimized geometry reduced the erosion rate at the inlet and dust discharge outlet by 20.4% and 21.8%, respectively, while the bionic rib structure reduced the maximum erosion rate by 58%.
- Open Access
Study on the Mechanical Transfer Mechanism of Bimetallic Composite Pipes in High-Steep Mountainous Areas
This paper investigates the mechanical transfer mechanism of bimetallic composite pipes used in highly sour gas fields located in high-steep mountainous areas. It systematically analyzes the mechanical response behavior of these pipes under the coupled effects of complex geological conditions and operational loads. By establishing and validating a finite element model that accounts for material nonlinearity and pipe–soil interaction, the study examines the influence of key factors—including internal pressure, landslide displacement, and base pipe wall thickness—on the stress distribution and transfer mechanism within the pipeline. The results demonstrate that increased internal pressure significantly elevates both circumferential and axial stresses: when internal pressure increases from 7 MPa to 9 MPa, the liner hoop stress increases by 35.5% and the base pipe axial stress increases by 27.5%. When landslide displacement exceeds a critical threshold of 3 m, the stress in the base pipe rises sharply, with axial stress increasing by 39.7% when displacement increases from 3 m to 5 m; conversely, increasing the base pipe wall thickness from 12 mm to 15 mm effectively reduces the overall stress level, decreasing base pipe axial stress by 40.4% and liner axial stress by 86.9%. Stress transfer exhibits a dual-path characteristic, which can be described as “bidirectional transfer induced by internal pressure” and “progressive transfer caused by landslide”. These quantitative findings provide a theoretical basis for the safe design and operation of bimetallic composite pipes in high-steep mountainous regions.
Open AccessStudy on the Mechanical Transfer Mechanism of Bimetallic Composite Pipes in High-Steep Mountainous Areas
This paper investigates the mechanical transfer mechanism of bimetallic composite pipes used in highly sour gas fields located in high-steep mountainous areas. It systematically analyzes the mechanical response behavior of these pipes under the coupled effects of complex geological conditions and operational loads. By establishing and validating a finite element model that accounts for material nonlinearity and pipe–soil interaction, the study examines the influence of key factors—including internal pressure, landslide displacement, and base pipe wall thickness—on the stress distribution and transfer mechanism within the pipeline. The results demonstrate that increased internal pressure significantly elevates both circumferential and axial stresses: when internal pressure increases from 7 MPa to 9 MPa, the liner hoop stress increases by 35.5% and the base pipe axial stress increases by 27.5%. When landslide displacement exceeds a critical threshold of 3 m, the stress in the base pipe rises sharply, with axial stress increasing by 39.7% when displacement increases from 3 m to 5 m; conversely, increasing the base pipe wall thickness from 12 mm to 15 mm effectively reduces the overall stress level, decreasing base pipe axial stress by 40.4% and liner axial stress by 86.9%. Stress transfer exhibits a dual-path characteristic, which can be described as “bidirectional transfer induced by internal pressure” and “progressive transfer caused by landslide”. These quantitative findings provide a theoretical basis for the safe design and operation of bimetallic composite pipes in high-steep mountainous regions.
- Open Access
Reliability Research of Natural Gas Pipeline Units Based on Mechanistic Modeling
Due to long-term burial underground, oil and gas pipelines are susceptible to external surface corrosion influenced by time and soil conditions, which can lead to leakage and burst failures. Pipeline failure not only results in significant economic losses but also has catastrophic impacts on human safety and the environment. Therefore, modeling and analyzing the corrosion failure of these pipelines is of critical practical importance to ensure their safe operation during service. Addressing the insufficient research on correlation effects in current reliability evaluations of corroded pipelines, this paper proposes a calculation method for the failure probability of corroded oil and gas pipelines that considers the influence of two-layer correlations. Taking a specific segment of the Shaanxi–Beijing pipeline as a case study, the Monte Carlo sampling algorithm is employed to calculate the impact of two-layer correlations and the quantity of defect on the pipeline’s failure probability. Furthermore, a sensitivity analysis of the correlation coefficients is conducted. The results indicate that the influence of defect correlation on pipeline failure probability is significantly more pronounced than that of random variable correlation. The probabilities of pinhole leakage and burst failure decrease as the correlation coefficient between defects increases, while they increase with the number of defects. Random variable correlation exhibits no impact on pinhole leakage probability; however, the burst failure probability decreases with an increasing correlation coefficient between wall thickness and pipe diameter, but increases as the correlation between initial defect length and depth grows. Furthermore, the correlation coefficient between axial and radial defect growth rates exerts a bidirectional effect on burst failure probability: during the first 25 years of the prediction period, the failure probability increases with the correlation coefficient, whereas it subsequently decreases after approximately 25 years. These findings are applicable to the reliability evaluation of oil and gas pipelines containing multiple corrosion defects, providing valuable technical references for ensuring safe operation and the steady supply of energy resources.
Open AccessReliability Research of Natural Gas Pipeline Units Based on Mechanistic Modeling
Due to long-term burial underground, oil and gas pipelines are susceptible to external surface corrosion influenced by time and soil conditions, which can lead to leakage and burst failures. Pipeline failure not only results in significant economic losses but also has catastrophic impacts on human safety and the environment. Therefore, modeling and analyzing the corrosion failure of these pipelines is of critical practical importance to ensure their safe operation during service. Addressing the insufficient research on correlation effects in current reliability evaluations of corroded pipelines, this paper proposes a calculation method for the failure probability of corroded oil and gas pipelines that considers the influence of two-layer correlations. Taking a specific segment of the Shaanxi–Beijing pipeline as a case study, the Monte Carlo sampling algorithm is employed to calculate the impact of two-layer correlations and the quantity of defect on the pipeline’s failure probability. Furthermore, a sensitivity analysis of the correlation coefficients is conducted. The results indicate that the influence of defect correlation on pipeline failure probability is significantly more pronounced than that of random variable correlation. The probabilities of pinhole leakage and burst failure decrease as the correlation coefficient between defects increases, while they increase with the number of defects. Random variable correlation exhibits no impact on pinhole leakage probability; however, the burst failure probability decreases with an increasing correlation coefficient between wall thickness and pipe diameter, but increases as the correlation between initial defect length and depth grows. Furthermore, the correlation coefficient between axial and radial defect growth rates exerts a bidirectional effect on burst failure probability: during the first 25 years of the prediction period, the failure probability increases with the correlation coefficient, whereas it subsequently decreases after approximately 25 years. These findings are applicable to the reliability evaluation of oil and gas pipelines containing multiple corrosion defects, providing valuable technical references for ensuring safe operation and the steady supply of energy resources.
- Open Access
Optimization of Triazine Desulfurization Injection Rate and Injection Process for the Xiangguosi Underground Gas Storage
Triazine solvent desulfurization is a highly efficient technology for removing hydrogen sulfide from natural gas. In this study, we used ASPEN HYSYS V11 with the Peng-Robinson (PR) equation to investigate the triazine consumption under different natural gas flow rates and hydrogen sulfide concentrations, as well as the sulfur capacity resulting from the reaction between triazine and H2S at varying solution concentrations. Additionally, CFD simulations were employed to optimize the injection process of the triazine solvent by examining four key factors: gas flow velocity, injection volume, injection angle, and injection method. The results indicate that the required triazine dosage follows an exponential model, with a margin of error within 10%. A triazine mass fraction between 0.4 and 0.6 was found to be optimal. Among the factors studied, gas flow velocity has the most significant influence on desulfurization efficiency, while the injection rate plays a secondary role. An injection angle of 45° proved most effective, and the use of dual vertical symmetric nozzles achieved more uniform mixing between the natural gas and triazine solvent.
Open AccessOptimization of Triazine Desulfurization Injection Rate and Injection Process for the Xiangguosi Underground Gas Storage
Triazine solvent desulfurization is a highly efficient technology for removing hydrogen sulfide from natural gas. In this study, we used ASPEN HYSYS V11 with the Peng-Robinson (PR) equation to investigate the triazine consumption under different natural gas flow rates and hydrogen sulfide concentrations, as well as the sulfur capacity resulting from the reaction between triazine and H2S at varying solution concentrations. Additionally, CFD simulations were employed to optimize the injection process of the triazine solvent by examining four key factors: gas flow velocity, injection volume, injection angle, and injection method. The results indicate that the required triazine dosage follows an exponential model, with a margin of error within 10%. A triazine mass fraction between 0.4 and 0.6 was found to be optimal. Among the factors studied, gas flow velocity has the most significant influence on desulfurization efficiency, while the injection rate plays a secondary role. An injection angle of 45° proved most effective, and the use of dual vertical symmetric nozzles achieved more uniform mixing between the natural gas and triazine solvent.
- Open Access
Research on Methods to Improve Liquefaction Efficiency of Supersonic Cyclone Devices
This research explores supersonic cyclonic separation for natural gas liquefaction (LNG). A 3D computational model was developed using the Eulerian–Eulerian two-fluid framework to simulate spontaneous gas condensation. The model tracks droplet formation/growth mechanisms and employs Reynolds stress modeling (RSM) for turbulence, implemented in Fluent via user-defined functions (UDFs). Validated against experimental data, it accurately predicted condensation onset and shock wave behavior. A prototype separator designed for a natural gas peak-shaving station demonstrated lower temperatures than throttling valves but modest liquefaction efficiency (4.28% at 5 MPa inlet pressure). Two enhancement strategies were tested: (1) injecting submicron LNG condensation nuclei (radius < 1 × 10−9 m) significantly boosted liquefaction by reducing nucleation energy barriers and suppressing condensation shocks; (2) a multi-stage configuration increased total liquefaction by 156% versus single-stage operation. These findings highlight the technology’s potential for energy-efficient gas processing.
Open AccessResearch on Methods to Improve Liquefaction Efficiency of Supersonic Cyclone Devices
This research explores supersonic cyclonic separation for natural gas liquefaction (LNG). A 3D computational model was developed using the Eulerian–Eulerian two-fluid framework to simulate spontaneous gas condensation. The model tracks droplet formation/growth mechanisms and employs Reynolds stress modeling (RSM) for turbulence, implemented in Fluent via user-defined functions (UDFs). Validated against experimental data, it accurately predicted condensation onset and shock wave behavior. A prototype separator designed for a natural gas peak-shaving station demonstrated lower temperatures than throttling valves but modest liquefaction efficiency (4.28% at 5 MPa inlet pressure). Two enhancement strategies were tested: (1) injecting submicron LNG condensation nuclei (radius < 1 × 10−9 m) significantly boosted liquefaction by reducing nucleation energy barriers and suppressing condensation shocks; (2) a multi-stage configuration increased total liquefaction by 156% versus single-stage operation. These findings highlight the technology’s potential for energy-efficient gas processing.
- Open Access
Stability Analysis of Polymer Flooding-Produced Liquid in Oilfields Based on Molecular Dynamics Simulation
The S oilfield has adopted polymer flooding technology, specifically using partially hydrolyzed polyacrylamide (HPAM), to enhance oil recovery. During the production process, the S oilfield has generated a substantial amount of stable polymer flooding-produced liquid, in which oil droplets are difficult to effectively coalesce, presenting significant challenges in demulsification. This article focuses on the produced fluids from S Oilfield as the research subject, developing a molecular dynamics model for the stability analysis of production liquid, including the molecular dynamics model of an oil–pure water system, an oil–mineralized water system and an oil–polymer–mineralized water system, using the principle of molecular dynamics and combining it with the basic molecular model for analyzing the stability of polymer flooding-production liquid. Through the molecular dynamics simulation of the stability analysis of the extracted liquid, the changing rules of the molecular diffusion coefficient, radial distribution function (RDF), interfacial interaction energy, and interfacial tension under the action of ions as well as polymers in water were investigated. The simulation results demonstrate that the presence of all three inorganic salt ions (Na+, Ca2+, and Mg2+) reduces the interfacial tension between oil and water and stabilizes the interface. Following the addition of polymer, the interfacial tension of the system decreases and the interfacial interaction energy increases significantly, indicating that the stability of the system is significantly enhanced by HPAM.
Open AccessStability Analysis of Polymer Flooding-Produced Liquid in Oilfields Based on Molecular Dynamics Simulation
The S oilfield has adopted polymer flooding technology, specifically using partially hydrolyzed polyacrylamide (HPAM), to enhance oil recovery. During the production process, the S oilfield has generated a substantial amount of stable polymer flooding-produced liquid, in which oil droplets are difficult to effectively coalesce, presenting significant challenges in demulsification. This article focuses on the produced fluids from S Oilfield as the research subject, developing a molecular dynamics model for the stability analysis of production liquid, including the molecular dynamics model of an oil–pure water system, an oil–mineralized water system and an oil–polymer–mineralized water system, using the principle of molecular dynamics and combining it with the basic molecular model for analyzing the stability of polymer flooding-production liquid. Through the molecular dynamics simulation of the stability analysis of the extracted liquid, the changing rules of the molecular diffusion coefficient, radial distribution function (RDF), interfacial interaction energy, and interfacial tension under the action of ions as well as polymers in water were investigated. The simulation results demonstrate that the presence of all three inorganic salt ions (Na+, Ca2+, and Mg2+) reduces the interfacial tension between oil and water and stabilizes the interface. Following the addition of polymer, the interfacial tension of the system decreases and the interfacial interaction energy increases significantly, indicating that the stability of the system is significantly enhanced by HPAM.