Junchen Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Junchen Wang has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Shubin Liu
University of Science and Technology of China
3 shared publications - Chang-Qing Feng
University of Science and Technology of China
2 shared publications - Wenhao Duan
University of Science and Technology of China
2 shared publications - Zhongtao Shen
State Key Laboratory of Particle Detection and Electronics, University of Science and Technology of China, Hefei 230026, China
2 shared publications Changqing Feng
State Key Laboratory of Particle Detection and Electronics and the Department of Modern Physics, University of Science and Technology of China, Hefei, China
1 shared publicationChen Zhai
State Key Laboratory of Particle Detection and Electronics and the Department of Modern Physics, University of Science and Technology of China, Hefei, China
1 shared publication
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 73 (10) , 4160-4170
Cluster Reconstruction Algorithm and FPGA Implementation for Pre-Research of the STCF ECAL L1 Trigger
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 73 (10) , 4160-4170
Cluster Reconstruction Algorithm and FPGA Implementation for Pre-Research of the STCF ECAL L1 Trigger
- 22 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 73 (6) , 2440-2449
An FPGA-Based Hybrid Wave Union Time-to-Digital Converter With Iterative Z-Type Code Calibration Algorithm
A novel FPGA-based multi-measurement scheme Time-to-Digital Converter (TDC) architecture, termed Hybrid Wave Union (HWU), is proposed. By integrating the advantages of the Wave Union A and Wave Union B methods, the designed TDC launches a ripple with multiple transitions along the tapped delay line (TDL) and samples it with a D flip-flop (DFF) array across consecutive system clock cycles upon the arrival of a rising edge, yielding two complementary snapshots. Each snapshot is encoded into fine timestamps through a pipeline encoder, and the resulting timestamp pairs are processed by an iterative Z-type calibration algorithm that reconstructs accurate delay intervals without requiring any predefined knowledge of the relative ordering of delay durations. The design is implemented on a Xilinx Kintex-7 FPGA, with a measured on-chip power consumption of 42 mW per channel, including 6 mW for the TDL and DFF bank, 31 mW for the encoder and packetization logic, and 5 mW shared across all TDC channels for the coarse time counter. Experimental results demonstrate an average RMS timing precision of 4.4 ps and a dead time of only three clock cycles—two for snapshot acquisition and one for TDL reset—significantly shorter than that of conventional Wave Union B TDCs. Compared to traditional TDL TDC architectures, the proposed HWU TDC achieves high timing precision, low resource utilization, and energy-efficient operation, making it well suited for multi-channel, high-precision applications in modern high-energy physics experiments.
- 22 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 73 (6) , 2440-2449
An FPGA-Based Hybrid Wave Union Time-to-Digital Converter With Iterative Z-Type Code Calibration Algorithm
A novel FPGA-based multi-measurement scheme Time-to-Digital Converter (TDC) architecture, termed Hybrid Wave Union (HWU), is proposed. By integrating the advantages of the Wave Union A and Wave Union B methods, the designed TDC launches a ripple with multiple transitions along the tapped delay line (TDL) and samples it with a D flip-flop (DFF) array across consecutive system clock cycles upon the arrival of a rising edge, yielding two complementary snapshots. Each snapshot is encoded into fine timestamps through a pipeline encoder, and the resulting timestamp pairs are processed by an iterative Z-type calibration algorithm that reconstructs accurate delay intervals without requiring any predefined knowledge of the relative ordering of delay durations. The design is implemented on a Xilinx Kintex-7 FPGA, with a measured on-chip power consumption of 42 mW per channel, including 6 mW for the TDL and DFF bank, 31 mW for the encoder and packetization logic, and 5 mW shared across all TDC channels for the coarse time counter. Experimental results demonstrate an average RMS timing precision of 4.4 ps and a dead time of only three clock cycles—two for snapshot acquisition and one for TDL reset—significantly shorter than that of conventional Wave Union B TDCs. Compared to traditional TDL TDC architectures, the proposed HWU TDC achieves high timing precision, low resource utilization, and energy-efficient operation, making it well suited for multi-channel, high-precision applications in modern high-energy physics experiments.
- 3 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 72 (3) , 705-712
An FPGA-Based High-Precision Pulsewidth Measurement Time-to-Digital Converter With Dual-TDL Multiplexer Encoder
High precision Time-to-Digital Converters (TDCs) play a pivotal role in contemporary particle physics experiments where the measurement of time-over-threshold (TOT) of signal pulses is essential. The stringent demand for picosecond resolution of pulse widths ranging from several hundred picoseconds to hundreds of nanoseconds, coupled with the high requirements for measurement throughput, presents formidable challenges in the design and optimization of pulse width measurement TDCs. This article introduces a novel dual tapped delay lines (TDL) TDC along with a dual-TDL multiplexer encoder to measure the arrival time and TOT time of signal pulses simultaneously in high precision. Utilizing the aforementioned architecture, a series of dual-TDL TDCs with 2,4,6,8-edge multiple measurements scheme capable of measuring the arrival time and TOT time simultaneously at 250 Msps are implemented in a Xilinx Kintex-7 FPGA. The minimum measurable pulse width is determined by the upper limit speed of the FPGA transmitting port and the characteristics of the high-speed comparator, test as 520 ps in our implementation. With pulse widths ranging from 520 ps to 1000 ns, the average TOT measurement RMS precision of the series TDCs is evaluated to be below 5.5 ps, which can be improved by the increasing times of multiple measurements. Specifically, the 8-edge dual-TDL TDC can achieve a precision as low as 3.4 ps. Furthermore The proposed dual-TDL TDC boasts resource efficiency and cost-effectiveness features, making it well suited for particle physics experiments that demand multi-channel capability at an affordable price, along with high performance.
- 3 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 72 (3) , 705-712
An FPGA-Based High-Precision Pulsewidth Measurement Time-to-Digital Converter With Dual-TDL Multiplexer Encoder
High precision Time-to-Digital Converters (TDCs) play a pivotal role in contemporary particle physics experiments where the measurement of time-over-threshold (TOT) of signal pulses is essential. The stringent demand for picosecond resolution of pulse widths ranging from several hundred picoseconds to hundreds of nanoseconds, coupled with the high requirements for measurement throughput, presents formidable challenges in the design and optimization of pulse width measurement TDCs. This article introduces a novel dual tapped delay lines (TDL) TDC along with a dual-TDL multiplexer encoder to measure the arrival time and TOT time of signal pulses simultaneously in high precision. Utilizing the aforementioned architecture, a series of dual-TDL TDCs with 2,4,6,8-edge multiple measurements scheme capable of measuring the arrival time and TOT time simultaneously at 250 Msps are implemented in a Xilinx Kintex-7 FPGA. The minimum measurable pulse width is determined by the upper limit speed of the FPGA transmitting port and the characteristics of the high-speed comparator, test as 520 ps in our implementation. With pulse widths ranging from 520 ps to 1000 ns, the average TOT measurement RMS precision of the series TDCs is evaluated to be below 5.5 ps, which can be improved by the increasing times of multiple measurements. Specifically, the 8-edge dual-TDL TDC can achieve a precision as low as 3.4 ps. Furthermore The proposed dual-TDL TDC boasts resource efficiency and cost-effectiveness features, making it well suited for particle physics experiments that demand multi-channel capability at an affordable price, along with high performance.