Oleh Bazarov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Oleh Bazarov has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Mykhailo Kovalenko
National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute
8 shared publications - Iryna Kovalenko
Національний технічний університет України «Київський політехнічний інститут імені Ігоря Сікорського», м. Київ
5 shared publications - Yehor Titov
Geko-Center LLC
4 shared publications - Mykola Reutskyi
NTUU ”Igor Sikorsky Kyiv Polytech-nic Institute“, Kyiv, Ukraine,Leading Researcher, Department No. 1 of Integrated Energy Systems, Institute of Re-newable Energy, NAS of Ukraine, Kyiv, Ukraine
3 shared publications - Serhii Tsyvinskyi
National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute
2 shared publications - Yurii Haidenko
National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute
2 shared publications
Latest Publications
- Open Access
- 23 June 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (5 (141)) , 17-25
Determining the effect of active losses on the thermal state of a high-speed permanent magnet motor
This study considers a high-speed permanent magnet motor designed to drive unmanned aerial vehicles and ground robotic systems. The scientific-practical task addressed is to establish a quantitative relationship between the components of electromagnetic losses and the thermal state of the motor in a wide range of operating modes (5000–23000 rpm, 1–54 A). A multiphysics numerical field mathematical model of a small-sized high-speed permanent magnet motor operating as part of an unmanned aerial vehicle has been constructed. The model resolves a coupled electromagnetic-thermal problem refining the temperature field distribution and parameters of active materials: the dependence of the residual magnetic induction of permanent magnets. It was found that the distribution of specific losses in the cross section is deeply uneven: the maximum values are concentrated at the edges of the stator teeth and exceed the losses in the permanent magnets and yoke by 1.5–2.5 orders of magnitude. The distribution of the thermal field with increasing current was established: at I ≤ 14 A, magnetic losses prevail, and at I > 27 A, losses in the winding become predominant and reach 201 W at a current of 54 A. This is 2.5–3.5 times more than magnetic losses. With increasing current, the loss curves for different speeds gradually coincide: at I = 54 A, the difference between 5000 and 23000 rpm is only ≈ 20 W (≈ 7% of the total losses of 260–280 W). At speeds above 17,000 rpm, the temperature of permanent magnets exceeds 80°C, the residual induction decreases by 6–8% of the rated value, which leads to a decrease in the electromagnetic torque by 3–4%. A critical value of the average motor heating has been established, at which the risk of irreversible demagnetization of magnets occurs, which corresponds to ≈ 216°C, at a speed of n > 11,000 rpm and at maximum current. The results could be used to optimize high-speed motors with permanent magnets
- 23 June 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (5 (141)) , 17-25
Open AccessDetermining the effect of active losses on the thermal state of a high-speed permanent magnet motor
This study considers a high-speed permanent magnet motor designed to drive unmanned aerial vehicles and ground robotic systems. The scientific-practical task addressed is to establish a quantitative relationship between the components of electromagnetic losses and the thermal state of the motor in a wide range of operating modes (5000–23000 rpm, 1–54 A). A multiphysics numerical field mathematical model of a small-sized high-speed permanent magnet motor operating as part of an unmanned aerial vehicle has been constructed. The model resolves a coupled electromagnetic-thermal problem refining the temperature field distribution and parameters of active materials: the dependence of the residual magnetic induction of permanent magnets. It was found that the distribution of specific losses in the cross section is deeply uneven: the maximum values are concentrated at the edges of the stator teeth and exceed the losses in the permanent magnets and yoke by 1.5–2.5 orders of magnitude. The distribution of the thermal field with increasing current was established: at I ≤ 14 A, magnetic losses prevail, and at I > 27 A, losses in the winding become predominant and reach 201 W at a current of 54 A. This is 2.5–3.5 times more than magnetic losses. With increasing current, the loss curves for different speeds gradually coincide: at I = 54 A, the difference between 5000 and 23000 rpm is only ≈ 20 W (≈ 7% of the total losses of 260–280 W). At speeds above 17,000 rpm, the temperature of permanent magnets exceeds 80°C, the residual induction decreases by 6–8% of the rated value, which leads to a decrease in the electromagnetic torque by 3–4%. A critical value of the average motor heating has been established, at which the risk of irreversible demagnetization of magnets occurs, which corresponds to ≈ 216°C, at a speed of n > 11,000 rpm and at maximum current. The results could be used to optimize high-speed motors with permanent magnets
- Open Access
- 30 April 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of NTU "KhPI". Series: Problems of Electrical Machines and Apparatus Perfection. The Theory and Practice
- No. 1 (15),p. 35-43
Evaluation of specific indicators of a high-speed axial flux permanent magnet motor
The paper evaluates the specific performance of a high-speed axial magnetic flux motor with excitation from permanent magnets, which is used as the main drive of electromechanical energy-efficient systems for aircraft. High requirements are imposed on aircraft engines for specific weight-dimensional characteristics, specific power and efficiency. In this study, the design features of an axial magnetic flux motor are analyzed using classical calculation methods. The main attention is paid to determining the relationship between the geometric dimensions of the active zone, the parameters of the magnetic system and electromagnetic loads that directly affect the specific performance of the motor. The paper uses analytical relationships to determine the main geometric dimensions, weight and specific performance of active materials and evaluates the share of the specific weight of the structural elements of such a motor. The work takes into account the influence of the design and main technical indicators of permanent magnets, the air gap size and winding topology on the energy and mass-dimensional indicators of the axial flux motor. The results obtained show that the use of an axial design motor with an axial nature of the main magnetic flux closure allows achieving increased values of specific power and reducing the mass of the motor compared to classical designs, especially in the power range of 7.0-9.0 kW, which is critically important for high-speed engines and aircraft. At the same time, limiting factors associated with thermal conditions, mechanical strength and losses at high speeds and magnetization reversal have been identified. The results of the study can be used in the design of compact high-efficiency electromechanical converters for transport, aviation and energy systems.
- 30 April 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of NTU "KhPI". Series: Problems of Electrical Machines and Apparatus Perfection. The Theory and Practice
- No. 1 (15),p. 35-43
Open AccessEvaluation of specific indicators of a high-speed axial flux permanent magnet motor
The paper evaluates the specific performance of a high-speed axial magnetic flux motor with excitation from permanent magnets, which is used as the main drive of electromechanical energy-efficient systems for aircraft. High requirements are imposed on aircraft engines for specific weight-dimensional characteristics, specific power and efficiency. In this study, the design features of an axial magnetic flux motor are analyzed using classical calculation methods. The main attention is paid to determining the relationship between the geometric dimensions of the active zone, the parameters of the magnetic system and electromagnetic loads that directly affect the specific performance of the motor. The paper uses analytical relationships to determine the main geometric dimensions, weight and specific performance of active materials and evaluates the share of the specific weight of the structural elements of such a motor. The work takes into account the influence of the design and main technical indicators of permanent magnets, the air gap size and winding topology on the energy and mass-dimensional indicators of the axial flux motor. The results obtained show that the use of an axial design motor with an axial nature of the main magnetic flux closure allows achieving increased values of specific power and reducing the mass of the motor compared to classical designs, especially in the power range of 7.0-9.0 kW, which is critically important for high-speed engines and aircraft. At the same time, limiting factors associated with thermal conditions, mechanical strength and losses at high speeds and magnetization reversal have been identified. The results of the study can be used in the design of compact high-efficiency electromechanical converters for transport, aviation and energy systems.
- Open Access
- 23 December 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (5 (138)) , 6-15
Determining the influence of structural and electromagnetic parameters on active losses in an electric motor with permanent magnets for unmanned aerial vehicles
This study investigates a small-sized high-speed permanent magnet motor used in the drive of unmanned aerial vehicles. As part of this study, a numerical simulation field mathematical model of a high-speed permanent magnet motor has been built, implemented by the finite element method. That made it possible to obtain the distribution of the electromagnetic field and forces, to estimate the total losses in all conductive and magnetically conductive media in individual structural elements of the permanent magnet motor under study. Unlike existing ones, the model built enables deriving the total losses in the calculation area; in permanent magnets, structural conductive elements, the armature winding, and in the magnetic core with hysteresis losses, eddy currents and additional losses caused by higher harmonics. The task addressed is predetermined by the pressing scientific-practical issue related to increasing the energy efficiency of a high-speed permanent magnet motor used for electric transport systems and unmanned aerial vehicles. The use of a simplified, more technological rectangular shape of permanent magnets has been proposed. Applying permanent magnets of this configuration makes it possible to reduce the total losses in the motor by 23…41% depending on the type of power supply – sinusoidal or when powered by an inverter with PWM. The use of a more technological form of permanent magnets leads to a decrease in the electromagnetic torque of the motor by approximately 18…30%, which is attributed to a decrease in the volume of active materials and an increase in the value of the equivalent air gap. At the same time, applying a modified form of permanent magnets makes it possible to reduce pulsations of the electromagnetic torque by 12%
- 23 December 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (5 (138)) , 6-15
Open AccessDetermining the influence of structural and electromagnetic parameters on active losses in an electric motor with permanent magnets for unmanned aerial vehicles
This study investigates a small-sized high-speed permanent magnet motor used in the drive of unmanned aerial vehicles. As part of this study, a numerical simulation field mathematical model of a high-speed permanent magnet motor has been built, implemented by the finite element method. That made it possible to obtain the distribution of the electromagnetic field and forces, to estimate the total losses in all conductive and magnetically conductive media in individual structural elements of the permanent magnet motor under study. Unlike existing ones, the model built enables deriving the total losses in the calculation area; in permanent magnets, structural conductive elements, the armature winding, and in the magnetic core with hysteresis losses, eddy currents and additional losses caused by higher harmonics. The task addressed is predetermined by the pressing scientific-practical issue related to increasing the energy efficiency of a high-speed permanent magnet motor used for electric transport systems and unmanned aerial vehicles. The use of a simplified, more technological rectangular shape of permanent magnets has been proposed. Applying permanent magnets of this configuration makes it possible to reduce the total losses in the motor by 23…41% depending on the type of power supply – sinusoidal or when powered by an inverter with PWM. The use of a more technological form of permanent magnets leads to a decrease in the electromagnetic torque of the motor by approximately 18…30%, which is attributed to a decrease in the volume of active materials and an increase in the value of the equivalent air gap. At the same time, applying a modified form of permanent magnets makes it possible to reduce pulsations of the electromagnetic torque by 12%
- 30 August 2025
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 4,p. 108-116
Mathematical simulation of brushless high-speed permanent magnet motor
Purpose. To develop a numerical two-dimensional field mathematical model of a brushless high-speed permanent magnet motor to estimate its parameters, characteristics and determine the magnitude of losses in the magnetic core under different control methods. Methodology. The finite element method was used to calculate the electromagnetic field distribution in the computational domain of the motor under study. To develop two-dimensional and three-dimensional drawings of the design area, methods and tools of computer-aided design were used. Numerical methods for calculating losses in the magnetic core developed by Giovanni Bertotti were used to calculate losses in the magnetic core. The Fourier series expansion method and spectral analysis methods were used to model various motor control methods. Findings. A two-dimensional numerical circular-field mathematical model of a brushless high-speed motor with permanent magnets has been developed. The model was developed to estimate the distribution of the electromagnetic field and eddy currents in the structural and active elements of the motor in question in order to determine the magnitude of losses under different power supply methods. The paper investigates the dependence of losses in individual structural elements of the motor under study when powered by a sinusoidal voltage source and when powered by a PWM inverter. Replacing permanent magnets with rectangular magnets reduces the cost of motor manufacturing. The use of rectangular permanent magnets reduces losses in the computational domain, the magnitude of electromagnetic torque fluctuations, but reduces the magnitude of traction. Originality. Using the developed numerical circular-field mathematical model, it is proved that losses in the magnetic core of a high-speed motor and its structural elements significantly depend on the control method and configuration of the magnetic system and the motor as a whole. The study allows solving urgent scientific and practical problems related to the optimization of the structure depending on the optimization criteria: reduction of heating or losses, reduction of vibration and noise, etc. Practical value. The modelling results indicate the prospects for the industrial implementation of high-speed permanent magnet motors as part of various complexes and systems: vehicles, hand-held power tools, aircraft, unmanned devices and systems, etc.
- 30 August 2025
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 4,p. 108-116
Mathematical simulation of brushless high-speed permanent magnet motor
Purpose. To develop a numerical two-dimensional field mathematical model of a brushless high-speed permanent magnet motor to estimate its parameters, characteristics and determine the magnitude of losses in the magnetic core under different control methods. Methodology. The finite element method was used to calculate the electromagnetic field distribution in the computational domain of the motor under study. To develop two-dimensional and three-dimensional drawings of the design area, methods and tools of computer-aided design were used. Numerical methods for calculating losses in the magnetic core developed by Giovanni Bertotti were used to calculate losses in the magnetic core. The Fourier series expansion method and spectral analysis methods were used to model various motor control methods. Findings. A two-dimensional numerical circular-field mathematical model of a brushless high-speed motor with permanent magnets has been developed. The model was developed to estimate the distribution of the electromagnetic field and eddy currents in the structural and active elements of the motor in question in order to determine the magnitude of losses under different power supply methods. The paper investigates the dependence of losses in individual structural elements of the motor under study when powered by a sinusoidal voltage source and when powered by a PWM inverter. Replacing permanent magnets with rectangular magnets reduces the cost of motor manufacturing. The use of rectangular permanent magnets reduces losses in the computational domain, the magnitude of electromagnetic torque fluctuations, but reduces the magnitude of traction. Originality. Using the developed numerical circular-field mathematical model, it is proved that losses in the magnetic core of a high-speed motor and its structural elements significantly depend on the control method and configuration of the magnetic system and the motor as a whole. The study allows solving urgent scientific and practical problems related to the optimization of the structure depending on the optimization criteria: reduction of heating or losses, reduction of vibration and noise, etc. Practical value. The modelling results indicate the prospects for the industrial implementation of high-speed permanent magnet motors as part of various complexes and systems: vehicles, hand-held power tools, aircraft, unmanned devices and systems, etc.
- Open Access
- 26 June 2025
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of NTU "KhPI". Series: Problems of Electrical Machines and Apparatus Perfection. The Theory and Practice
- No. 1 (13),p. 50-55
Linearized dynamic model of magnetic transmission
The work is devoted to the development of a linearized numerical mathematical model of a contactless electromechanical energy converter with permanent magnets - magnetic transmission. Magnetic transmissions have certain design advantages compared to mechanical transmissions, namely: high reliability, efficiency, lower losses, contactless transmission of mechanical power, no maintenance costs, simplicity of design. The use of magnetic transmissions for systems for converting low-potential mechanical energy into electrical energy is especially relevant: wind energy, water energy, mechanical vibration energy, etc. The use of magnetic transmissions in autonomous wind power plants may be more promising from an economic and technical point of view compared to traditional mechanical transmissions. As an alternative to the dynamic model, which is inconvenient to use at the initial stages of design, for the purpose of initial assessment of oscillation parameters, a linearized dynamic model of magnetic transmission has been developed, in which the relationship between the moment and the load angle is represented by a non-sinusoidal function, and its linear approximation in the operating torque domain. Using the developed model, the parameters and characteristics of not only the magnetic transmission, but also other components of the system have been investigated: an electric source of electric energy, a wind turbine, load, etc., which increases the variability and opportunities for conducting scientific research of an exploratory nature. The developed simulation model of magnetic transmission takes into account the pulsations of the electromagnetic moment through the discrete structure of the magnetic transmission and the change in the model parameters when the input torque changes: pulsations, losses in the magnetic core and permanent magnets, a change in the load angle and the transmitted electromagnetic moment.
- 26 June 2025
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of NTU "KhPI". Series: Problems of Electrical Machines and Apparatus Perfection. The Theory and Practice
- No. 1 (13),p. 50-55
Open AccessLinearized dynamic model of magnetic transmission
The work is devoted to the development of a linearized numerical mathematical model of a contactless electromechanical energy converter with permanent magnets - magnetic transmission. Magnetic transmissions have certain design advantages compared to mechanical transmissions, namely: high reliability, efficiency, lower losses, contactless transmission of mechanical power, no maintenance costs, simplicity of design. The use of magnetic transmissions for systems for converting low-potential mechanical energy into electrical energy is especially relevant: wind energy, water energy, mechanical vibration energy, etc. The use of magnetic transmissions in autonomous wind power plants may be more promising from an economic and technical point of view compared to traditional mechanical transmissions. As an alternative to the dynamic model, which is inconvenient to use at the initial stages of design, for the purpose of initial assessment of oscillation parameters, a linearized dynamic model of magnetic transmission has been developed, in which the relationship between the moment and the load angle is represented by a non-sinusoidal function, and its linear approximation in the operating torque domain. Using the developed model, the parameters and characteristics of not only the magnetic transmission, but also other components of the system have been investigated: an electric source of electric energy, a wind turbine, load, etc., which increases the variability and opportunities for conducting scientific research of an exploratory nature. The developed simulation model of magnetic transmission takes into account the pulsations of the electromagnetic moment through the discrete structure of the magnetic transmission and the change in the model parameters when the input torque changes: pulsations, losses in the magnetic core and permanent magnets, a change in the load angle and the transmitted electromagnetic moment.
- Open Access
- 26 June 2025
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of NTU "KhPI". Series: Problems of Electrical Machines and Apparatus Perfection. The Theory and Practice
- No. 1 (13),p. 44-49
Experimental study of autonomous magnetic transmission
The work is devoted to the experimental study of a non-contact electromechanical energy converter with permanent magnets - magnetic transmission. Magnetic transmissions have certain design advantages compared to mechanical transmissions, namely: high reliability, efficiency, lower losses, non-contact transmission of mechanical power, no maintenance costs, and simplicity of design. The use of magnetic transmissions for systems of conversion of low-potential mechanical energy into electrical energy is especially relevant: wind energy, water energy, energy of mechanical vibrations, etc. The application of magnetic transmissions in autonomous wind power plants can be more promising from the economic and technical point of view compared to traditional mechanical transmissions. In order to conduct experimental studies, at the first stage of this study, a geometric model of magnetic transmission was developed in the automated design system. With the use of detailed drawings, the main structural elements of the magnetic transmission were printed using three-dimensional printing technologies. Magnetic segments of the magnetic transmission modulator, permanent magnets, shaft, bearings and bearing shields were installed. On the basis of the developed mock-up sample of the magnetic transmission, an experimental stand for the study of magnetic transmission was developed, with the help of which a number of experimental studies were carried out: measurement of rotation speed and gear ratio, losses, heating and electromagnetic moment. The conducted studies and the developed electromechanical stand allow conducting various studies of magnetic transmissions, which will allow to confirm the results of mathematical modeling and to confirm or refute the results of scientific studies.
- 26 June 2025
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of NTU "KhPI". Series: Problems of Electrical Machines and Apparatus Perfection. The Theory and Practice
- No. 1 (13),p. 44-49
Open AccessExperimental study of autonomous magnetic transmission
The work is devoted to the experimental study of a non-contact electromechanical energy converter with permanent magnets - magnetic transmission. Magnetic transmissions have certain design advantages compared to mechanical transmissions, namely: high reliability, efficiency, lower losses, non-contact transmission of mechanical power, no maintenance costs, and simplicity of design. The use of magnetic transmissions for systems of conversion of low-potential mechanical energy into electrical energy is especially relevant: wind energy, water energy, energy of mechanical vibrations, etc. The application of magnetic transmissions in autonomous wind power plants can be more promising from the economic and technical point of view compared to traditional mechanical transmissions. In order to conduct experimental studies, at the first stage of this study, a geometric model of magnetic transmission was developed in the automated design system. With the use of detailed drawings, the main structural elements of the magnetic transmission were printed using three-dimensional printing technologies. Magnetic segments of the magnetic transmission modulator, permanent magnets, shaft, bearings and bearing shields were installed. On the basis of the developed mock-up sample of the magnetic transmission, an experimental stand for the study of magnetic transmission was developed, with the help of which a number of experimental studies were carried out: measurement of rotation speed and gear ratio, losses, heating and electromagnetic moment. The conducted studies and the developed electromechanical stand allow conducting various studies of magnetic transmissions, which will allow to confirm the results of mathematical modeling and to confirm or refute the results of scientific studies.
- Open Access
- 30 April 2025
- Published by National University "Zaporizhzhia Polytechnic" in Electrical Engineering and Power Engineering
- No. 1,p. 7-16
Operation of autonomous electromechanical converters of low and medium power
Purpose. To assess the reliability of operation of low and medium power electromechanical converters based on real experience in operating such systems. Methodology. Statistical analysis methods, classical calculation methods for synchronous salient pole generators with electromagnetic excitation. Findings. An analysis of failure statistics of autonomous electromechanical converters of small and medium power was carried out. The results obtained emphasize the need to implement generator condition monitoring systems for early detection of malfunctions. Regular diagnostics and load control will help prevent critical breakdowns and increase the service life of the equipment. The collected statistical data can be used to develop effective preventive measures, improve maintenance instructions and optimize generator operating modes. Further research can be aimed at developing algorithms for automatic load distribution between phases, improving protection systems and increasing the reliability of insulating materials. An analysis of the failure statistics of diesel and gasoline generators showed that electrical breakdowns account for 51% of cases, and mechanical ones - 49%. This indicates an approximately even distribution between the two categories of failures, which indicates the need for a comprehensive approach to maintenance and diagnostics. When using these installations for military purposes, the balance of failures shifts: mechanical failures: 75-85%, electrical failures: 15-25%. Among electrical failures, the most common are damage to the stator windings due to load asymmetry, failure of voltage regulators, malfunctions of the battery system and violations of the insulation of the electrical wiring. Mechanical failures are most often associated with wear of the piston group, insufficient lubrication, engine overheating due to malfunctions of the cooling system and malfunctions in the fuel system. Originality. A detailed generalization of the experience of operating autonomous electromechanical converters in real conditions was carried out, which allowed us to establish the regularities of their operation, identify typical problems and develop recommendations for their elimination. The methods for assessing the efficiency of autonomous electromechanical converters proposed in the study can be used for further modernization of existing systems, as well as for creating new highly efficient autonomous power generating units. Practical value. The results of the study have practical value for engineers, users and manufacturers of electromechanical equipment. The results obtained can be used to improve the efficiency and reliability of autonomous power systems operating in various conditions. In particular, it is possible to reduce maintenance costs, improve energy efficiency and extend the service life of the equipment. The results obtained can be used in the development of recommendations for the selection, modernization and diagnostics of autonomous electromechanical installations.
- 30 April 2025
- Published by National University "Zaporizhzhia Polytechnic" in Electrical Engineering and Power Engineering
- No. 1,p. 7-16
Open AccessOperation of autonomous electromechanical converters of low and medium power
Purpose. To assess the reliability of operation of low and medium power electromechanical converters based on real experience in operating such systems. Methodology. Statistical analysis methods, classical calculation methods for synchronous salient pole generators with electromagnetic excitation. Findings. An analysis of failure statistics of autonomous electromechanical converters of small and medium power was carried out. The results obtained emphasize the need to implement generator condition monitoring systems for early detection of malfunctions. Regular diagnostics and load control will help prevent critical breakdowns and increase the service life of the equipment. The collected statistical data can be used to develop effective preventive measures, improve maintenance instructions and optimize generator operating modes. Further research can be aimed at developing algorithms for automatic load distribution between phases, improving protection systems and increasing the reliability of insulating materials. An analysis of the failure statistics of diesel and gasoline generators showed that electrical breakdowns account for 51% of cases, and mechanical ones - 49%. This indicates an approximately even distribution between the two categories of failures, which indicates the need for a comprehensive approach to maintenance and diagnostics. When using these installations for military purposes, the balance of failures shifts: mechanical failures: 75-85%, electrical failures: 15-25%. Among electrical failures, the most common are damage to the stator windings due to load asymmetry, failure of voltage regulators, malfunctions of the battery system and violations of the insulation of the electrical wiring. Mechanical failures are most often associated with wear of the piston group, insufficient lubrication, engine overheating due to malfunctions of the cooling system and malfunctions in the fuel system. Originality. A detailed generalization of the experience of operating autonomous electromechanical converters in real conditions was carried out, which allowed us to establish the regularities of their operation, identify typical problems and develop recommendations for their elimination. The methods for assessing the efficiency of autonomous electromechanical converters proposed in the study can be used for further modernization of existing systems, as well as for creating new highly efficient autonomous power generating units. Practical value. The results of the study have practical value for engineers, users and manufacturers of electromechanical equipment. The results obtained can be used to improve the efficiency and reliability of autonomous power systems operating in various conditions. In particular, it is possible to reduce maintenance costs, improve energy efficiency and extend the service life of the equipment. The results obtained can be used in the development of recommendations for the selection, modernization and diagnostics of autonomous electromechanical installations.
- Open Access
- 31 March 2025
- Published by Vidnovluvana energetika in Vidnovluvana energetika
- No. 1(80),p. 29-37
ВИКОРИСТАННЯ ДЖЕРЕЛА БЕЗПЕРЕБІЙНОГО ЖИВЛЕННЯ ДЛЯ ЗНИЖЕННЯ ЕКСПЛУАТАЦІЙНИХ ВИТРАТ АВТОНОМНОГО ЕЛЕКТРОГЕНЕРАТОРА
Проведено аналіз використання джерела безперебійного живлення сумісно з автономним дизель-бензиновим електрогенератором з метою зниження експлуатаційних витрат. Такі системи мають місце при використанні автономної електрогенерувальної установки як єдиного джерела живлення споживачів, або в разі аварійних чи екстрених відключень електроенергії. Проведено аналіз існуючих систем автономного енергозабезпечення та обґрунтовано актуальність цього напряму дослідження. На конкретному прикладі автономної електроустановки та певного переліку обладнання приватного будинку побудовано графіки навантажень залежно від часу доби. За розробленими алгоритмами проведено оцінку ефективності використання ДБЖ у парі з автономною дизель-бензиновою електрогенерувальною установкою. Використання ДБЖ дає змогу знизити експлуатаційні витрати за рахунок навантаження генератора до оптимального значення 75–80 % номінального, економити паливо, скоротити інтервали й періодичність технічного обслуговування та зменшити шкідливі викиди в атмосферу. Максимальна величина заощаджень залежно від режиму роботи системи, характеру навантаження й періодичності відключень становить від 39 до 76 %. Збільшити ефект енергозбереження можливо, якщо цю систему додатково спорядити сонячними панелями чи вітрогенератором. Це дозволить додатково заощаджувати паливо та ресурс роботи електрогенератора. Оцінку ефективності цього технічного рішення планується провести під час майбутніх досліджень.
- 31 March 2025
- Published by Vidnovluvana energetika in Vidnovluvana energetika
- No. 1(80),p. 29-37
Open AccessВИКОРИСТАННЯ ДЖЕРЕЛА БЕЗПЕРЕБІЙНОГО ЖИВЛЕННЯ ДЛЯ ЗНИЖЕННЯ ЕКСПЛУАТАЦІЙНИХ ВИТРАТ АВТОНОМНОГО ЕЛЕКТРОГЕНЕРАТОРА
Проведено аналіз використання джерела безперебійного живлення сумісно з автономним дизель-бензиновим електрогенератором з метою зниження експлуатаційних витрат. Такі системи мають місце при використанні автономної електрогенерувальної установки як єдиного джерела живлення споживачів, або в разі аварійних чи екстрених відключень електроенергії. Проведено аналіз існуючих систем автономного енергозабезпечення та обґрунтовано актуальність цього напряму дослідження. На конкретному прикладі автономної електроустановки та певного переліку обладнання приватного будинку побудовано графіки навантажень залежно від часу доби. За розробленими алгоритмами проведено оцінку ефективності використання ДБЖ у парі з автономною дизель-бензиновою електрогенерувальною установкою. Використання ДБЖ дає змогу знизити експлуатаційні витрати за рахунок навантаження генератора до оптимального значення 75–80 % номінального, економити паливо, скоротити інтервали й періодичність технічного обслуговування та зменшити шкідливі викиди в атмосферу. Максимальна величина заощаджень залежно від режиму роботи системи, характеру навантаження й періодичності відключень становить від 39 до 76 %. Збільшити ефект енергозбереження можливо, якщо цю систему додатково спорядити сонячними панелями чи вітрогенератором. Це дозволить додатково заощаджувати паливо та ресурс роботи електрогенератора. Оцінку ефективності цього технічного рішення планується провести під час майбутніх досліджень.