F. Qayyum
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
F. Qayyum has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
A. Muqeet
Fracture Mechanics and Fatigue Laboratory, Mechanical Engineering Department, University of Engineering and Technology, Taxila, Pakistan
1 shared publicationJ. Afzal
Fracture Mechanics and Fatigue Laboratory, Mechanical Engineering Department, University of Engineering and Technology, Taxila, Pakistan
1 shared publicationM. Shah
Fracture Mechanics and Fatigue Laboratory, Mechanical Engineering Department, University of Engineering and Technology, Taxila, Pakistan
1 shared publication- Masood Shah
University of Engineering and Technology
1 shared publication - Muhammad Shahid Khalil
Department of Mechanical Engineering, University of Engineering and Technology, Taxila 47080, Pakistan
1 shared publication - Muhammad Zubair Khan
Institute of Space Technology Department of Mechanical Engineering 1 Islamabad Expressway, Islamabad 44000 , Pakistan
1 shared publication
Latest Publications
- Open Access
- 1 August 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 146 (1) , 012031
The effect of anisotropy on the intermediate and final form in deep drawing of SS304L, with high draw ratios: Experimentation and numerical simulation
High deep draw ratio of metal sheets is often required in industry to produce complex structural components and is considered to be problematic beyond a draw ratio of 1.7. In addition, anisotropy of material plays a great role in the final form of deep drawn products. In this research AISI SS304 L high draw ratio deep drawing (HDR) cups have been developed by using multiple intermediate annealing steps. The form of flange produced at each draw step is recorded, Numerical simulation of the process is carried out using ABAQUS StandardTM. Accurate modelling of the process requires anisotropic parameters. Tensile tests at 0o, 15o, 30o, 45o, 60o, 75o, 90o to the rolling direction are carried out to determine the Lankford coefficients and hardening coefficients in each direction. The detailed material data obtained is then applied to simulate the HDR process. The forms recorded experimentally are compared with simulation results and conclusion is drawn as to the accuracy of the simulation.
- 1 August 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 146 (1) , 012031
Open AccessThe effect of anisotropy on the intermediate and final form in deep drawing of SS304L, with high draw ratios: Experimentation and numerical simulation
High deep draw ratio of metal sheets is often required in industry to produce complex structural components and is considered to be problematic beyond a draw ratio of 1.7. In addition, anisotropy of material plays a great role in the final form of deep drawn products. In this research AISI SS304 L high draw ratio deep drawing (HDR) cups have been developed by using multiple intermediate annealing steps. The form of flange produced at each draw step is recorded, Numerical simulation of the process is carried out using ABAQUS StandardTM. Accurate modelling of the process requires anisotropic parameters. Tensile tests at 0o, 15o, 30o, 45o, 60o, 75o, 90o to the rolling direction are carried out to determine the Lankford coefficients and hardening coefficients in each direction. The detailed material data obtained is then applied to simulate the HDR process. The forms recorded experimentally are compared with simulation results and conclusion is drawn as to the accuracy of the simulation.
- Open Access
- 13 December 2015
- Published by Pakistan Atomic Energy Commission in The Nucleus
- Vol. 52 (4) , 169-175
Shear Strain Model for Equal Channel Angular Pressing in High Elastic Extruded Plastics
This paper presents a novel model for plastic shear strain calculation in the Equal Channel Angular Pressing (ECAP). The model is particularly formulated to furnish for the elastic recovery after extrusion. Due to high elastic recovery after plastic deformation in polymers, the behavior of Teflon and Nylon is investigated at different temperatures as they are famous for their low coefficient of friction and wall friction effects. The main concentration is given to the basic principle of ECAP processing parameters such as strain, slip bands, and shearing patterns. In this research, a new engraved circle marking technique is used to trace the plastic deformation in the specimens. Afterwards, image analysis approach is applied to measure the deformation, strain and rotation after extrusion. The experimental results are validated with the ABAQUS based numerical simulation. A close conformity is found between them.
- 13 December 2015
- Published by Pakistan Atomic Energy Commission in The Nucleus
- Vol. 52 (4) , 169-175
Open AccessShear Strain Model for Equal Channel Angular Pressing in High Elastic Extruded Plastics
This paper presents a novel model for plastic shear strain calculation in the Equal Channel Angular Pressing (ECAP). The model is particularly formulated to furnish for the elastic recovery after extrusion. Due to high elastic recovery after plastic deformation in polymers, the behavior of Teflon and Nylon is investigated at different temperatures as they are famous for their low coefficient of friction and wall friction effects. The main concentration is given to the basic principle of ECAP processing parameters such as strain, slip bands, and shearing patterns. In this research, a new engraved circle marking technique is used to trace the plastic deformation in the specimens. Afterwards, image analysis approach is applied to measure the deformation, strain and rotation after extrusion. The experimental results are validated with the ABAQUS based numerical simulation. A close conformity is found between them.