Iryna Osypenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Iryna Osypenko has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Yuriy Dotsenko
Ukrainian State University of Science and Technologies
2 shared publications - Alevtyna Pereverzieva
National Technical University “Kharkiv Polytechnic Institute
1 shared publication - Alona Dzevochko
National Technical University “Kharkiv Polytechnic Institute
1 shared publication - Denys Nikolaiev
National Technical University "Kharkiv Polytechnic Institute
1 shared publication - Dmytro Makarenko
National Aerospace University “Kharkiv Aviation Institute
1 shared publication - Eugene Kuznetsow
Educational and Research Institute "Dnipro Institute of Infrastructure and Transport" of the Ukrainian State University of Science and Technology
1 shared publication
Latest Publications
- Open Access
- 29 December 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 6 (1(86)) , 43-47
Determination of conditions for preventing chemical wear of induction furnace lining in the “cupola furnace – induction furnace” duplex process
The object of research is the melting of cast iron in the “cupola furnace – induction furnace” duplex process. The need to study such a duplex process is dictated by the condition of ensuring the required quality of cast iron in the event that a low-quality or uncontrolled charge is used. This condition cannot be met if the induction furnace is used as the only melting unit. But the problem is that in the process of induction melting of cast iron, in particular at the stage of overheating and holding the melt, a crucible reaction may begin, which leads to chemical wear of the lining. The need to reduce the carbon content in the melt discharged from the cupola furnace requires an increase in temperatures, which creates risks for the onset of a crucible reaction. Based on statistical calculations of cupola melting parameters, it was found that in the melt discharged from the cupola furnace into the induction furnace, the average carbon content is C = 3.47% with a standard deviation SC = 0.14%, and the average silicon content is Si = 2.05% with a standard deviation SSi = 0.21%. At the same time, with a probability of 96%, the carbon content is C = (3.33–3.75)%, and the silicon content corresponds to the range Si = (1.84–2.46)% with a probability of 98%. It was found that the equilibrium constant is in the range (0.15–0.21) with a probability of 97.8% at an average temperature T = 1355°C with a standard deviation of temperature ST = 6°C. With such melt parameters, which are supplied to the induction furnace, the risks of the onset of a crucible reaction do not arise. It was determined that even at temperature regimes sufficient to remove FeO, the risk of the onset of a crucible reaction is minimal. In order to ensure conditions that prevent the onset of a crucible reaction, the following recommendations should be followed for the content of carbon and silicon in high-temperature melting when the temperature is in the range T > 1480°C: C > 0.3% and Si < 0.3%. The results of the study can be used in the melting sections of foundries equipped with cupola furnaces and induction furnaces.
- 29 December 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 6 (1(86)) , 43-47
Open AccessDetermination of conditions for preventing chemical wear of induction furnace lining in the “cupola furnace – induction furnace” duplex process
The object of research is the melting of cast iron in the “cupola furnace – induction furnace” duplex process. The need to study such a duplex process is dictated by the condition of ensuring the required quality of cast iron in the event that a low-quality or uncontrolled charge is used. This condition cannot be met if the induction furnace is used as the only melting unit. But the problem is that in the process of induction melting of cast iron, in particular at the stage of overheating and holding the melt, a crucible reaction may begin, which leads to chemical wear of the lining. The need to reduce the carbon content in the melt discharged from the cupola furnace requires an increase in temperatures, which creates risks for the onset of a crucible reaction. Based on statistical calculations of cupola melting parameters, it was found that in the melt discharged from the cupola furnace into the induction furnace, the average carbon content is C = 3.47% with a standard deviation SC = 0.14%, and the average silicon content is Si = 2.05% with a standard deviation SSi = 0.21%. At the same time, with a probability of 96%, the carbon content is C = (3.33–3.75)%, and the silicon content corresponds to the range Si = (1.84–2.46)% with a probability of 98%. It was found that the equilibrium constant is in the range (0.15–0.21) with a probability of 97.8% at an average temperature T = 1355°C with a standard deviation of temperature ST = 6°C. With such melt parameters, which are supplied to the induction furnace, the risks of the onset of a crucible reaction do not arise. It was determined that even at temperature regimes sufficient to remove FeO, the risk of the onset of a crucible reaction is minimal. In order to ensure conditions that prevent the onset of a crucible reaction, the following recommendations should be followed for the content of carbon and silicon in high-temperature melting when the temperature is in the range T > 1480°C: C > 0.3% and Si < 0.3%. The results of the study can be used in the melting sections of foundries equipped with cupola furnaces and induction furnaces.
- Open Access
- 4 April 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 2 (1(82)) , 19-23
Construction of a kinetic equation of carbon removal for controlling steel melting in the metallurgical system “cupola furnace – small converter”
The object of research in the paper is the process of steelmaking in a small converter, which works in tandem with a cupola furnace. The existing problem is that the control of the process of obtaining steel in an oxygen converter is complicated by the need to determine in real time the current chemical composition of the melt, in particular carbon. This is due to the fact that the rate of carbon removal is too high, as a result of which the process of carbon removal is transient. Therefore, it is too difficult to implement regulation based on feedback on continuous measurement. The presence of the specified problem requires solutions related to the possibilities of developing or improving software control of the process. It is shown that in certain sections of the process within each time section of oxygen purging of the melt in the converter, the kinetic curve has a linear form with a constant coefficient value in front of the inlet mine. But the value of the initial coefficient for each equation that describes the process within its limits changes. This allows to state that in case of a change in the initial condition, the kinetic curves shift relative to each other in parallel. On this basis, a system of equations has been constructed that describes the process of carbon removal in a small oxygen converter that receives liquid iron from a cupola furnace. It has been shown that to use the obtained system of equations, it is necessary to know the initial carbon content in the melt discharged from the cupola furnace, and it depends on the method of oxygen supply to the cupola furnace. Based on the modeling of this process in two variants – using a “sharp blow” and supplying oxygen to the air blown into the tuyeres, a nomogram has been constructed. It allows to determine the initial carbon content for the practical use of the obtained system of equations. Using the obtained system makes it possible to determine the time after which oxygen cutoff should be made. This will allow to decide to implement software control of the melt blowing process in the converter. The presented study will be useful for machine-building enterprises that have foundry shops in their structure, where cast iron is smelted for the manufacture of castings.
- 4 April 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 2 (1(82)) , 19-23
Open AccessConstruction of a kinetic equation of carbon removal for controlling steel melting in the metallurgical system “cupola furnace – small converter”
The object of research in the paper is the process of steelmaking in a small converter, which works in tandem with a cupola furnace. The existing problem is that the control of the process of obtaining steel in an oxygen converter is complicated by the need to determine in real time the current chemical composition of the melt, in particular carbon. This is due to the fact that the rate of carbon removal is too high, as a result of which the process of carbon removal is transient. Therefore, it is too difficult to implement regulation based on feedback on continuous measurement. The presence of the specified problem requires solutions related to the possibilities of developing or improving software control of the process. It is shown that in certain sections of the process within each time section of oxygen purging of the melt in the converter, the kinetic curve has a linear form with a constant coefficient value in front of the inlet mine. But the value of the initial coefficient for each equation that describes the process within its limits changes. This allows to state that in case of a change in the initial condition, the kinetic curves shift relative to each other in parallel. On this basis, a system of equations has been constructed that describes the process of carbon removal in a small oxygen converter that receives liquid iron from a cupola furnace. It has been shown that to use the obtained system of equations, it is necessary to know the initial carbon content in the melt discharged from the cupola furnace, and it depends on the method of oxygen supply to the cupola furnace. Based on the modeling of this process in two variants – using a “sharp blow” and supplying oxygen to the air blown into the tuyeres, a nomogram has been constructed. It allows to determine the initial carbon content for the practical use of the obtained system of equations. Using the obtained system makes it possible to determine the time after which oxygen cutoff should be made. This will allow to decide to implement software control of the melt blowing process in the converter. The presented study will be useful for machine-building enterprises that have foundry shops in their structure, where cast iron is smelted for the manufacture of castings.