Amanda J. Hughes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Amanda J. Hughes has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Abhinav Kumar Singh
Department of Materials, Design & Manufacturing Engineering School of Engineering University of Liverpool Liverpool UK
4 shared publications - Laurie J. Phillips
University of Liverpool
4 shared publications - Hissah Alghathami
Department of Materials, Design & Manufacturing Engineering School of Engineering University of Liverpool Liverpool UK
3 shared publications - Qian Chen
Department of Materials, Design & Manufacturing Engineering School of Engineering University of Liverpool Liverpool UK
3 shared publications - Aeshah Almushawwah
Stephenson Institute for Renewable Energy, Department of Physics, University of Liverpool, Liverpool, L69 7ZF, UK
2 shared publications - Jonathan Douglas Major
University of Liverpool
2 shared publications
Latest Publications
- Open Access
- 6 July 2026
- Published by Elsevier in SSRN Electronic Journal
Tuning bulk charge transport and interfacial passivation in sputtered SnO2 films through an oxygen-engineered bilayer design for perovskite solar cells
Tin oxide (SnO2) is the benchmark electron transport layer (ETL) for n-i-p emerging perovskite solar cells (PSCs). Sputtering offers a scalable, industry-compatible deposition method, providing excellent control and uniformity over large areas. However, sputtered SnO2 ETL often requires an additional passivation layer to ensure efficient charge collection. This work demonstrates that the optoelectronic properties of sputtered SnO2 strongly depend on oxygen partial pressure during deposition. Low oxygen (≤15%) passivates the interface with perovskite due to the presence of metallic Sn, increasing the open-circuit voltage (VOC). However, this comes at the cost of reduced fill-factor and short-circuit current densities (JSC) due to increased series resistance caused by -OH trap states. In contrast, higher oxygen content in the chamber (≥20%) reduces the series resistance and enhances JSC, but degrades the interfacial contact, lowering VOC. To overcome this trade-off, we design a bilayer sputtered-SnO2 ETL, comprising a 20 nm high-oxygen-content (25%) bulk layer for efficient electron transport, and a 5 nm low-oxygen-content (15%) interface layer to passivate surface defects. This bilayer strategy yields an enhanced power conversion efficiency (PCE), achieving 12.13%, compared to 5.50% and 9.72% for single-layer SnO2 deposited under 15% and 25% oxygen, respectively, for champion devices made under ambient conditions.
- 6 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessTuning bulk charge transport and interfacial passivation in sputtered SnO2 films through an oxygen-engineered bilayer design for perovskite solar cells
Tin oxide (SnO2) is the benchmark electron transport layer (ETL) for n-i-p emerging perovskite solar cells (PSCs). Sputtering offers a scalable, industry-compatible deposition method, providing excellent control and uniformity over large areas. However, sputtered SnO2 ETL often requires an additional passivation layer to ensure efficient charge collection. This work demonstrates that the optoelectronic properties of sputtered SnO2 strongly depend on oxygen partial pressure during deposition. Low oxygen (≤15%) passivates the interface with perovskite due to the presence of metallic Sn, increasing the open-circuit voltage (VOC). However, this comes at the cost of reduced fill-factor and short-circuit current densities (JSC) due to increased series resistance caused by -OH trap states. In contrast, higher oxygen content in the chamber (≥20%) reduces the series resistance and enhances JSC, but degrades the interfacial contact, lowering VOC. To overcome this trade-off, we design a bilayer sputtered-SnO2 ETL, comprising a 20 nm high-oxygen-content (25%) bulk layer for efficient electron transport, and a 5 nm low-oxygen-content (15%) interface layer to passivate surface defects. This bilayer strategy yields an enhanced power conversion efficiency (PCE), achieving 12.13%, compared to 5.50% and 9.72% for single-layer SnO2 deposited under 15% and 25% oxygen, respectively, for champion devices made under ambient conditions.
- Open Access
- 15 April 2026
- Published by Wiley in ChemSusChem
- Vol. 19 (8) , e202502742
Impact of Electron Transport Layers on Hysteresis and Performance of Ambient‐Processed Perovskite Solar Cells
Ambient processing of perovskite solar cells (PSCs) offers a promising route to scalable and low‐cost manufacturing. While substantial progress has been achieved in improving power conversion efficiency (PCE), the hysteresis behavior of ambient‐processed devices remains insufficiently understood. This study examines hysteresis in PSCs fabricated in ambient air at 40–65% Relative humidity (RH) using multiple absorber compositions, including MAPbI 3 , CsFAPbI 3 , and Cs 2 AgBiBr 6 . Severe hysteresis is observed in devices employing planar TiO 2 or SnO 2 electron transport layers (ETLs), attributed to amplified moisture‐ and oxygen‐induced defect formation in ambient air. To overcome this challenge, ETL architecture is systematically engineered by adjusting planar TiO 2 thickness and incorporating mesoscopic TiO 2 architecture with controlled thicknesses. An optimized configuration featuring an approximately 140 nm mesoporous layer substantially reduces hysteresis, lowering the hysteresis index (HI) in MAPbI 3 PSCs from 0.52 for planar TiO 2 to 0.19, enhancing stability while maintaining high PCE. Similar improvements are demonstrated for CsFAPbI 3 , where the HI decreases from 0.56 for planar TiO 2 and 0.47 for planar SnO 2 to 0.38, and for Cs 2 AgBiBr 6 , where the HI decreases from 0.32 to 0.08. These findings highlight ETL structural engineering as an effective strategy for mitigating hysteresis and enabling reliable ambient‐processed PSCs for scalable manufacturing.
- 15 April 2026
- Published by Wiley in ChemSusChem
- Vol. 19 (8) , e202502742
Open AccessImpact of Electron Transport Layers on Hysteresis and Performance of Ambient‐Processed Perovskite Solar Cells
Ambient processing of perovskite solar cells (PSCs) offers a promising route to scalable and low‐cost manufacturing. While substantial progress has been achieved in improving power conversion efficiency (PCE), the hysteresis behavior of ambient‐processed devices remains insufficiently understood. This study examines hysteresis in PSCs fabricated in ambient air at 40–65% Relative humidity (RH) using multiple absorber compositions, including MAPbI 3 , CsFAPbI 3 , and Cs 2 AgBiBr 6 . Severe hysteresis is observed in devices employing planar TiO 2 or SnO 2 electron transport layers (ETLs), attributed to amplified moisture‐ and oxygen‐induced defect formation in ambient air. To overcome this challenge, ETL architecture is systematically engineered by adjusting planar TiO 2 thickness and incorporating mesoscopic TiO 2 architecture with controlled thicknesses. An optimized configuration featuring an approximately 140 nm mesoporous layer substantially reduces hysteresis, lowering the hysteresis index (HI) in MAPbI 3 PSCs from 0.52 for planar TiO 2 to 0.19, enhancing stability while maintaining high PCE. Similar improvements are demonstrated for CsFAPbI 3 , where the HI decreases from 0.56 for planar TiO 2 and 0.47 for planar SnO 2 to 0.38, and for Cs 2 AgBiBr 6 , where the HI decreases from 0.32 to 0.08. These findings highlight ETL structural engineering as an effective strategy for mitigating hysteresis and enabling reliable ambient‐processed PSCs for scalable manufacturing.
- Open Access
- 13 July 2025
- Published by Wiley in Energy Technology
- Vol. 13 (11)
Impact of Deposition Temperature on the Performance of Sputtered SnO 2 Electron Transport Layer in Perovskite Solar Cells
The drive to commercialize perovskite solar cells (PSCs) requires the development of scalable fabrication techniques. Sputtering, being an industrial technique, offers a promising approach for fabricating SnO 2 electron transport layers (ETLs). This study looks into the effect of deposition temperature in the range of 20–400 °C during sputtering of SnO 2 . The sputtered films are characterized using various optoelectronic techniques such as X‐ray photoelectron spectroscopy, grazing incidence X‐ray diffraction, and Hall effect measurements. Full‐scale device testing demonstrates that a deposition temperature of 100 °C is optimal for achieving peak PSC performance, attributed to enhanced SnO 2 crystallinity, improved FTO, and SnO 2 surface chemistry and low sheet resistivity of the tin oxide films. This study demonstrates the viability of sputtering for ETL fabrication, with the low processing temperature of this technique, making it ideal for commercialization, especially for flexible PSCs.
- 13 July 2025
- Published by Wiley in Energy Technology
- Vol. 13 (11)
Open AccessImpact of Deposition Temperature on the Performance of Sputtered SnO 2 Electron Transport Layer in Perovskite Solar Cells
The drive to commercialize perovskite solar cells (PSCs) requires the development of scalable fabrication techniques. Sputtering, being an industrial technique, offers a promising approach for fabricating SnO 2 electron transport layers (ETLs). This study looks into the effect of deposition temperature in the range of 20–400 °C during sputtering of SnO 2 . The sputtered films are characterized using various optoelectronic techniques such as X‐ray photoelectron spectroscopy, grazing incidence X‐ray diffraction, and Hall effect measurements. Full‐scale device testing demonstrates that a deposition temperature of 100 °C is optimal for achieving peak PSC performance, attributed to enhanced SnO 2 crystallinity, improved FTO, and SnO 2 surface chemistry and low sheet resistivity of the tin oxide films. This study demonstrates the viability of sputtering for ETL fabrication, with the low processing temperature of this technique, making it ideal for commercialization, especially for flexible PSCs.
- Open Access
- 29 April 2025
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 27 (25) , 7532-7543
Ambient and green processing of lead-free double perovskite Cs2AgBiBr6 films
A green and simple method for processing high-quality lead-free perovskite Cs2AgBiBr6 films under ambient conditions for future optoelectronic applications.
- 29 April 2025
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 27 (25) , 7532-7543
Open AccessAmbient and green processing of lead-free double perovskite Cs2AgBiBr6 films
A green and simple method for processing high-quality lead-free perovskite Cs2AgBiBr6 films under ambient conditions for future optoelectronic applications.