Alperen Mulayim Korkmaz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Alperen Mulayim Korkmaz has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Cevdet Yalciner
Department of Civil Engineering, Middle East Technical University, Ankara, Turkey
4 shared publications - Aysen Ergin
Gulizar Ozyurt Tarakcioglu Isikhan Guler Yalciner Technical University Middle East Technical University Middle East Technical University Middle East Technical University Middle East Technical University Middle East Technical University Middle East Technical University Izmir Institute of Technology Middle East Technical University Middle East Technical University Middle East Technical University
4 shared publications - Cuneyt Baykal
Gulizar Ozyurt Tarakcioglu Isikhan Guler Yalciner Technical University Middle East Technical University Middle East Technical University Middle East Technical University Middle East Technical University Middle East Technical University Middle East Technical University Izmir Institute of Technology Middle East Technical University Middle East Technical University Middle East Technical University
4 shared publications - Gulizar Ozyurt Tarakcioglu
Middle East Technical University
4 shared publications - Hasan Gokhan Guler
Gulizar Ozyurt Tarakcioglu Isikhan Guler Yalciner Technical University Middle East Technical University Middle East Technical University Middle East Technical University Middle East Technical University Middle East Technical University Middle East Technical University Izmir Institute of Technology Middle East Technical University Middle East Technical University Middle East Technical University
4 shared publications - Isikhan Guler
Department of Civil Engineering, Coastal and Ocean Engineering Division, Middle East Technical University, Ankara, Türkiye
4 shared publications
Latest Publications
- Open Access
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 85
CFD MODELING OF THE EFFECT OF ANTIFER UNITS USED IN THE ARMOR LAYER OF MOUND BREAKWATERS ON WAVE OVERTOPPING
Accurate prediction of wave overtopping is crucial for designing mound breakwaters. It is a common practice to use empirical equations (e.g. EurOtop, 2018) to determine wave overtopping discharges for practical purposes. On the other hand, with the help of the exponential increase in computer technology, the use of computational fluid dynamics (CFD) tools for wave overtopping is becoming widespread (e.g. Chen et al., 2021). In coastal engineering CFD applications, it is a common practice to model the mound breakwaters using a macro porous media modeling approach, where the overall flow behavior through the porous media is mimicked (Guler, 2020). Volume-averaged Reynolds- averaged Navier–Stokes (VARANS) equations are an integral part of the macro porous media modeling approach. However, the appropriate application of VARANS equations strongly depends on the friction coefficients, especially when investigating the processes around the porous regions. These coefficients appear in the VARANS equations due to volume averaging based on the Darcy-Forchheimer Equation. Although Jensen et al. (2014) previously carried out an extensive study for the calibration of these friction coefficients under different conditions considering flow through rocks, the effects of different armor units, placement methods, and packing density have not been studied in the literature yet. This study delves into the calibration of friction coefficients within the VARANS equations for Antifer units used in the armor layer of mound breakwaters with different placement methods (closed pyramid, double pyramid, and irregular) and packing densities by comparing the results with the physical model experiments. Thus, this research aims to increase the accuracy of CFD assessments on wave overtopping, offering important opportunities for the design of coastal structures.
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 85
Open AccessCFD MODELING OF THE EFFECT OF ANTIFER UNITS USED IN THE ARMOR LAYER OF MOUND BREAKWATERS ON WAVE OVERTOPPING
Accurate prediction of wave overtopping is crucial for designing mound breakwaters. It is a common practice to use empirical equations (e.g. EurOtop, 2018) to determine wave overtopping discharges for practical purposes. On the other hand, with the help of the exponential increase in computer technology, the use of computational fluid dynamics (CFD) tools for wave overtopping is becoming widespread (e.g. Chen et al., 2021). In coastal engineering CFD applications, it is a common practice to model the mound breakwaters using a macro porous media modeling approach, where the overall flow behavior through the porous media is mimicked (Guler, 2020). Volume-averaged Reynolds- averaged Navier–Stokes (VARANS) equations are an integral part of the macro porous media modeling approach. However, the appropriate application of VARANS equations strongly depends on the friction coefficients, especially when investigating the processes around the porous regions. These coefficients appear in the VARANS equations due to volume averaging based on the Darcy-Forchheimer Equation. Although Jensen et al. (2014) previously carried out an extensive study for the calibration of these friction coefficients under different conditions considering flow through rocks, the effects of different armor units, placement methods, and packing density have not been studied in the literature yet. This study delves into the calibration of friction coefficients within the VARANS equations for Antifer units used in the armor layer of mound breakwaters with different placement methods (closed pyramid, double pyramid, and irregular) and packing densities by comparing the results with the physical model experiments. Thus, this research aims to increase the accuracy of CFD assessments on wave overtopping, offering important opportunities for the design of coastal structures.
- Open Access
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 87
EFFECTS OF DIFFERENT UNITS AND PLACEMENT METHODS ON WAVE OVERTOPPING ON MOUND BREAKWATERS
Most of the existing and widely used wave run-up and overtopping formulas reflect the effect of different units placed at the armor layers of mound breakwaters utilizing a roughness coefficient (f) specifically assigned for the unit type (see e.g. TAW, 2002; EurOtop, 2018). However, the effect of the different armor placement methods has not been fully addressed in these approaches. The purpose of the present study is to investigate the effects of different placement methods and packing densities of different armor units on wave overtopping. Within this scope, an experimental study was carried out using quarry rocks, tetrapod and Antifer units along the armor layer of conventional mound breakwater cross-sections having two different face slopes. In the experiments, both the mean overtopping discharges (q) and individual overtopping volumes (Vind) were measured. The experimental results are compared with the computations based on the most prevalent formulas in practice.
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 87
Open AccessEFFECTS OF DIFFERENT UNITS AND PLACEMENT METHODS ON WAVE OVERTOPPING ON MOUND BREAKWATERS
Most of the existing and widely used wave run-up and overtopping formulas reflect the effect of different units placed at the armor layers of mound breakwaters utilizing a roughness coefficient (f) specifically assigned for the unit type (see e.g. TAW, 2002; EurOtop, 2018). However, the effect of the different armor placement methods has not been fully addressed in these approaches. The purpose of the present study is to investigate the effects of different placement methods and packing densities of different armor units on wave overtopping. Within this scope, an experimental study was carried out using quarry rocks, tetrapod and Antifer units along the armor layer of conventional mound breakwater cross-sections having two different face slopes. In the experiments, both the mean overtopping discharges (q) and individual overtopping volumes (Vind) were measured. The experimental results are compared with the computations based on the most prevalent formulas in practice.
- Open Access
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 79
EFFECTS OF DIFFERENT ARMOUR UNITS AND PLACEMENT METHODS ON WAVE LOADS ACTING ON CROWN WALLS
Numerous previous experiments aimed to clarify and predict the detailed mechanism of wave forces on crown walls of mound breakwaters. However, a comprehensive study has not yet been conducted for cases involving different placement methods and packing densities of armour units. This study examines how various placement methods and packing densities of tetrapod and Antifer units, in combination with natural rocks in the armour layer design, influence the distribution of wave forces on the crown walls. Physical model tests were carried out using 1:1.5 and 1:2 face slopes, allowing for modifications to model units in the armour layer and a comparison of changes in wave-induced forces experienced by the crown wall. As a result of the study, the empirical coefficients of Pedersen (1996) formulae adjusted by Norgaard et al. (2013) for shallow water condition were modified for Antifer and tetrapod units.
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 79
Open AccessEFFECTS OF DIFFERENT ARMOUR UNITS AND PLACEMENT METHODS ON WAVE LOADS ACTING ON CROWN WALLS
Numerous previous experiments aimed to clarify and predict the detailed mechanism of wave forces on crown walls of mound breakwaters. However, a comprehensive study has not yet been conducted for cases involving different placement methods and packing densities of armour units. This study examines how various placement methods and packing densities of tetrapod and Antifer units, in combination with natural rocks in the armour layer design, influence the distribution of wave forces on the crown walls. Physical model tests were carried out using 1:1.5 and 1:2 face slopes, allowing for modifications to model units in the armour layer and a comparison of changes in wave-induced forces experienced by the crown wall. As a result of the study, the empirical coefficients of Pedersen (1996) formulae adjusted by Norgaard et al. (2013) for shallow water condition were modified for Antifer and tetrapod units.
- Open Access
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 93
HYDRAULIC TESTS ON A XBLOCPLUS ARMOURED COASTAL REVETMENT
In this study, the hydraulic tests performed on a XBlocPlus® armoured coastal revetment structure to be constructed at the mid-western Black Sea coast of Turkey are presented. The revetment structure protects a reclaimed area next to a thermal power-plant. The tests include measurements regarding i) the stability of the armour layer, ii) mean and individual wave overtopping iii) wave loads on the crown wall, and iv) overtopping induced scour at the lee-side. The revetment structure has an approximate length of 1 km. The toe depth varies between -7 m to -17 m (mean sea level, MSL). The design high water level (HWL) corresponding to 100-yr return period is calculated as +0.95 m. The nearshore bottom slope is around 1:30. The design significant wave height and the peak period at the toe of the structure with a 100- yr return period are given as Hm0 = 8.53 m and Ts = 9.91 s at the deepest section of the structure. The volume of the blocks used in the armour layer of the revetment varies as 6 m3, 14 m3 and 18 m3 from the shallowest region to the deepest section. The study covers the experiments performed for the section with 18 m3 blocks and a toe depth of -17 m (MSL).
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 93
Open AccessHYDRAULIC TESTS ON A XBLOCPLUS ARMOURED COASTAL REVETMENT
In this study, the hydraulic tests performed on a XBlocPlus® armoured coastal revetment structure to be constructed at the mid-western Black Sea coast of Turkey are presented. The revetment structure protects a reclaimed area next to a thermal power-plant. The tests include measurements regarding i) the stability of the armour layer, ii) mean and individual wave overtopping iii) wave loads on the crown wall, and iv) overtopping induced scour at the lee-side. The revetment structure has an approximate length of 1 km. The toe depth varies between -7 m to -17 m (mean sea level, MSL). The design high water level (HWL) corresponding to 100-yr return period is calculated as +0.95 m. The nearshore bottom slope is around 1:30. The design significant wave height and the peak period at the toe of the structure with a 100- yr return period are given as Hm0 = 8.53 m and Ts = 9.91 s at the deepest section of the structure. The volume of the blocks used in the armour layer of the revetment varies as 6 m3, 14 m3 and 18 m3 from the shallowest region to the deepest section. The study covers the experiments performed for the section with 18 m3 blocks and a toe depth of -17 m (MSL).