Laís Alves Candido
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Laís Alves Candido has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Betty Salazar Mayta
Universidade Federal de Uberlândia, Brazil
1 shared publication - Flávio Domingues das Neves
Federal University of Uberlândia
1 shared publication - Gustavo Mendonça
Virginia Commonwealth University, USA
1 shared publication - Karla Zancopé
Federal University of Uberlândia
1 shared publication - Paulo Cézar Simamoto Júnior
Universidade Federal de Uberlândia, Brasil
1 shared publication
Latest Publications
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Brazilian Oral Research
- Vol. 39, e060
Effect of preservation on the mechanical properties of 3D printing resins for occlusal splints
This study aims to evaluate the mechanical properties of 3D printing resins for occlusal splints (OS) under different preservation conditions based on sleep duration. The study factors (n = 10) included material types: PriZma 3D Bio Splint (PZ), Cosmos Splint (CS), NightGuard Firm (NGF), and self-polymerizing acrylic resin (control group - CG); preservation: artificial saliva (S), natural water (W), 0.12% chlorhexidine (C), and Corega tabs (CTs); and evaluation times: T0 (24 h after fabrication) and 30 d after exposure. Further, the surface roughness (Ra), Knoop microhardness (KH), three-point flexural strength (FS), and flexural modulus (FM) were analyzed. In terms of the time and material, Tukey’s test revealed no significant differences in Ra between the groups at 24 h. After 30 d, PZ showed significantly lower values than the other groups (p < 0.05). For the KH, NGF was significantly higher than that in all groups at 24 h (p < 0.05); after 30 d, the NGF decreased in W and C (p < 0.05), and the NGF and PZ exhibited elevated values in S and CT, respectively. The Kruskal–Wallis test and multiple comparisons showed that the PZ had a higher value at 24 h (p < 0.05). Post 30 d, all 3D-printing resins increased values in CT and S (p < 0.05), and the PZ decreased in the C and W (P < 0.05). Finally, the FM increased under all conditions. The preservation of S and CT partially enhanced the mechanical properties of the OS.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Brazilian Oral Research
- Vol. 39, e060
Open AccessEffect of preservation on the mechanical properties of 3D printing resins for occlusal splints
This study aims to evaluate the mechanical properties of 3D printing resins for occlusal splints (OS) under different preservation conditions based on sleep duration. The study factors (n = 10) included material types: PriZma 3D Bio Splint (PZ), Cosmos Splint (CS), NightGuard Firm (NGF), and self-polymerizing acrylic resin (control group - CG); preservation: artificial saliva (S), natural water (W), 0.12% chlorhexidine (C), and Corega tabs (CTs); and evaluation times: T0 (24 h after fabrication) and 30 d after exposure. Further, the surface roughness (Ra), Knoop microhardness (KH), three-point flexural strength (FS), and flexural modulus (FM) were analyzed. In terms of the time and material, Tukey’s test revealed no significant differences in Ra between the groups at 24 h. After 30 d, PZ showed significantly lower values than the other groups (p < 0.05). For the KH, NGF was significantly higher than that in all groups at 24 h (p < 0.05); after 30 d, the NGF decreased in W and C (p < 0.05), and the NGF and PZ exhibited elevated values in S and CT, respectively. The Kruskal–Wallis test and multiple comparisons showed that the PZ had a higher value at 24 h (p < 0.05). Post 30 d, all 3D-printing resins increased values in CT and S (p < 0.05), and the PZ decreased in the C and W (P < 0.05). Finally, the FM increased under all conditions. The preservation of S and CT partially enhanced the mechanical properties of the OS.