Hendrik Jimmyanto
Hendrik Jimmyanto has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Muhammad Imam Ammarullah
Department of Mechanical and Aerospace Engineering College of Engineering United Arab Emirates University Al Ain United Arab Emirates
2 shared publications - Ramadhani Ramadhani
Universitas IBA
2 shared publications - Abdulfatah Abdu Yusuf
University of Liberia
1 shared publication - Ani Firda
Department of Civil Engineering, Faculty of Engineering, Universitas Tridinanti
1 shared publication - Edi Kadarsa
Sriwijaya University
1 shared publication - Harmein Rahman
Institut Teknologi Bandung
1 shared publication
Latest Publications
- Open Access
- 1 May 2026
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 30 (3) , 310-323
Performance Characterization of Rubberized Asphalt Mixtures Incorporating Waste Tire and Solid Natural Rubber
The performance of asphalt mixtures modified with 7% and 10% waste tire and solid natural rubber is assessed in this study, along with the effects of replacing fine aggregate with these materials. According to binder testing, a 10% rubber modification improved viscosity and deformation resistance while raising the softening point to 62.25°C. According to Marshall's findings, modified binders needed a higher optimal asphalt content of 6.05% to 6.25%. While the 7% modification produced the highest stability of 23.0 kN, replacing 50% of the river sand with Solid Natural Rubber decreased stability to 6.29 kN, falling short of requirements due to reduced structural rigidity. The 10% rubber mixture showed notable increases in stiffness modulus, increasing by 88.99% at 25°C and 105.69% at 40°C, according to testing. Additionally, the 10% modification achieved the highest durability, with 3,701 cycles, a 9.4% improvement over the control, according to the Indirect Tensile Fatigue Test results. According to the study's findings, rubber modifications of 7% and 10% greatly increase load-bearing capacity and fatigue resistance; however, in order to preserve the pavement's structural stability and integrity, rubber use as a fine aggregate replacement must be strictly limited.
- 1 May 2026
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 30 (3) , 310-323
Open AccessPerformance Characterization of Rubberized Asphalt Mixtures Incorporating Waste Tire and Solid Natural Rubber
The performance of asphalt mixtures modified with 7% and 10% waste tire and solid natural rubber is assessed in this study, along with the effects of replacing fine aggregate with these materials. According to binder testing, a 10% rubber modification improved viscosity and deformation resistance while raising the softening point to 62.25°C. According to Marshall's findings, modified binders needed a higher optimal asphalt content of 6.05% to 6.25%. While the 7% modification produced the highest stability of 23.0 kN, replacing 50% of the river sand with Solid Natural Rubber decreased stability to 6.29 kN, falling short of requirements due to reduced structural rigidity. The 10% rubber mixture showed notable increases in stiffness modulus, increasing by 88.99% at 25°C and 105.69% at 40°C, according to testing. Additionally, the 10% modification achieved the highest durability, with 3,701 cycles, a 9.4% improvement over the control, according to the Indirect Tensile Fatigue Test results. According to the study's findings, rubber modifications of 7% and 10% greatly increase load-bearing capacity and fatigue resistance; however, in order to preserve the pavement's structural stability and integrity, rubber use as a fine aggregate replacement must be strictly limited.
- Open Access
- 20 June 2025
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 22 (1)
Bio-Based Rice Husk Ash as an Eco-Friendly Filler in Pre-Vulcanized Latex Asphalt Concrete Wearing Course Mixtures
- 20 June 2025
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 22 (1)
Open AccessBio-Based Rice Husk Ash as an Eco-Friendly Filler in Pre-Vulcanized Latex Asphalt Concrete Wearing Course Mixtures
- Open Access
- 29 May 2025
- Published by Wiley in Engineering Reports
- Vol. 7 (6)
Artificial Polymer Lightweight Aggregate Concrete With Coal Fly Ash for Biomedical Infrastructure: Mechanical, Physical, and Microstructural Investigation
Aggregates constitute ~60%–80% of concrete volume and play a crucial role in determining its mechanical and durability properties. In the context of sustainable construction, artificial aggregates derived from industrial by‐products are gaining prominence as environmentally responsible alternatives to natural aggregates. This study presents the development and performance evaluation of a novel lightweight concrete incorporating artificial polymer lightweight aggregate synthesized from coal fly ash (CFA), epoxy resin, and a hardener in varying CFA‐to‐resin ratios (70:30, 74:26, and 80:20 by weight). The proposed mix design aims to address the increasing demand for lightweight, durable, and sustainable materials suitable for biomedical infrastructure applications, which require enhanced thermal insulation, fire resistance, and seismic performance. Concrete mixtures were designed to achieve target compressive strengths of 17.5, 20, and 30 MPa, with both lightweight (BR series) and normal weight (BN series) concrete formulations evaluated. Results demonstrated that the incorporation of polymer lightweight aggregates reduced the bulk density of concrete by up to 15.36%, while meeting or exceeding the required compressive strength thresholds for BR_17.5 and BR_20 mixtures. Although the BR_30 mix did not meet the target strength, polymer lightweight aggregate‐based concrete exhibited significantly improved flexural strength (up to 60.57% higher than conventional mixes) and enhanced chemical durability when exposed to acidic and saline environments. However, its resistance to elevated temperatures was lower compared to that of conventional concrete. The findings suggest that polymer lightweight aggregate concrete offers a promising sustainable material solution for biomedical infrastructure and other applications demanding lightweight, durable, and thermally efficient construction materials. The utilization of industrial waste in polymer lightweight aggregate production not only contributes to environmental conservation but also advances the development of next‐generation building materials aligned with circular economy principles.
- 29 May 2025
- Published by Wiley in Engineering Reports
- Vol. 7 (6)
Open AccessArtificial Polymer Lightweight Aggregate Concrete With Coal Fly Ash for Biomedical Infrastructure: Mechanical, Physical, and Microstructural Investigation
Aggregates constitute ~60%–80% of concrete volume and play a crucial role in determining its mechanical and durability properties. In the context of sustainable construction, artificial aggregates derived from industrial by‐products are gaining prominence as environmentally responsible alternatives to natural aggregates. This study presents the development and performance evaluation of a novel lightweight concrete incorporating artificial polymer lightweight aggregate synthesized from coal fly ash (CFA), epoxy resin, and a hardener in varying CFA‐to‐resin ratios (70:30, 74:26, and 80:20 by weight). The proposed mix design aims to address the increasing demand for lightweight, durable, and sustainable materials suitable for biomedical infrastructure applications, which require enhanced thermal insulation, fire resistance, and seismic performance. Concrete mixtures were designed to achieve target compressive strengths of 17.5, 20, and 30 MPa, with both lightweight (BR series) and normal weight (BN series) concrete formulations evaluated. Results demonstrated that the incorporation of polymer lightweight aggregates reduced the bulk density of concrete by up to 15.36%, while meeting or exceeding the required compressive strength thresholds for BR_17.5 and BR_20 mixtures. Although the BR_30 mix did not meet the target strength, polymer lightweight aggregate‐based concrete exhibited significantly improved flexural strength (up to 60.57% higher than conventional mixes) and enhanced chemical durability when exposed to acidic and saline environments. However, its resistance to elevated temperatures was lower compared to that of conventional concrete. The findings suggest that polymer lightweight aggregate concrete offers a promising sustainable material solution for biomedical infrastructure and other applications demanding lightweight, durable, and thermally efficient construction materials. The utilization of industrial waste in polymer lightweight aggregate production not only contributes to environmental conservation but also advances the development of next‐generation building materials aligned with circular economy principles.