Maksim V. Kovtun
Maksim V. Kovtun has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Sergey A. Kurlovich
Trading and Industrial Company SYNTEZ
2 shared publications - Dmitry N. Gladkih
Don State Technical University
1 shared publication - Evgeniy Fominov
Don State Technical University
1 shared publication - I.A. Mikhailova1 shared publication
- Q.T. Tran1 shared publication
- Tatyana Lavrenova
Don State Technical University
1 shared publication
Latest Publications
- 5 August 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 279
High-stability diamond nanofluid for enhanced photothermal conversion in direct absorption solar collectors
- 5 August 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 279
High-stability diamond nanofluid for enhanced photothermal conversion in direct absorption solar collectors
- Open Access
- 1 January 2025
- Published by Togliatti State University in Frontier materials & technologies
- No. 2,p. 87-94
The influence of cavitational synthesis nanodiamonds on the tribological properties of a water-oil-based cooling lubricant
This paper deals with the study of the influence of nanosized diamonds produced by the cavitational synthesis method on the tribological properties of a commercial water-oil-based cooling lubricant. The study is aimed at assessing the prospects for application of this type of nanodiamonds as an antifriction and antiwear additive. Tribological tests were carried out using the “indenter on a disk” friction scheme at a constant load and sliding speed. High-speed P18 steel for the indenter and 30HGSA steel for the rotating counterbody (disk) were used as friction couple materials. The studies were carried out for the base lubricant and two variants of its composition modifications using colloidal dispersion (distilled water with dispersed nanodiamonds) with a final additive concentration of 0.5 and 2.5 %. It was experimentally found that both variants of modification of the base water-oil emulsion resulted in increase of the bearing capacity of lubricating layers, decreasing the total linear wear of friction couple elements by 1.8–2.4 times. The presence of nanodiamonds in the composition enhanced as well the shielding effect of the cutting coolant. A decrease in visible damage to friction surfaces was recorded using optical microscopy. Analysis of profile diagrams of worn areas in the transverse direction showed a decrease in the size of a groove on the counterbody against the background of a decrease in roughness from Ra=0.49 μm in the basic variant to Ra=0.29–0.34 μm. Evaluation of the loss in counterbody weight for nanodiamond concentrations of 0.5 and 2.5 % showed a decrease in their value by 1.3 and 1.9 times, respectively; for the indenter, the decrease in this parameter was 1.2 and 1.5 times. Thus, the use of cavitational synthesis nanodiamonds as an additive may become a promising direction for increasing the antiwear properties of water-oil-based cooling lubricants.
- 1 January 2025
- Published by Togliatti State University in Frontier materials & technologies
- No. 2,p. 87-94
Open AccessThe influence of cavitational synthesis nanodiamonds on the tribological properties of a water-oil-based cooling lubricant
This paper deals with the study of the influence of nanosized diamonds produced by the cavitational synthesis method on the tribological properties of a commercial water-oil-based cooling lubricant. The study is aimed at assessing the prospects for application of this type of nanodiamonds as an antifriction and antiwear additive. Tribological tests were carried out using the “indenter on a disk” friction scheme at a constant load and sliding speed. High-speed P18 steel for the indenter and 30HGSA steel for the rotating counterbody (disk) were used as friction couple materials. The studies were carried out for the base lubricant and two variants of its composition modifications using colloidal dispersion (distilled water with dispersed nanodiamonds) with a final additive concentration of 0.5 and 2.5 %. It was experimentally found that both variants of modification of the base water-oil emulsion resulted in increase of the bearing capacity of lubricating layers, decreasing the total linear wear of friction couple elements by 1.8–2.4 times. The presence of nanodiamonds in the composition enhanced as well the shielding effect of the cutting coolant. A decrease in visible damage to friction surfaces was recorded using optical microscopy. Analysis of profile diagrams of worn areas in the transverse direction showed a decrease in the size of a groove on the counterbody against the background of a decrease in roughness from Ra=0.49 μm in the basic variant to Ra=0.29–0.34 μm. Evaluation of the loss in counterbody weight for nanodiamond concentrations of 0.5 and 2.5 % showed a decrease in their value by 1.3 and 1.9 times, respectively; for the indenter, the decrease in this parameter was 1.2 and 1.5 times. Thus, the use of cavitational synthesis nanodiamonds as an additive may become a promising direction for increasing the antiwear properties of water-oil-based cooling lubricants.