Nursultan Rakhym
Nursultan Rakhym has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Sanat Tolendiuly
Institute of Combustion Problems, Bogenbay Batyr St. 172, Almaty 050012, Kazakhstan
6 shared publications - Sharafkhan Assylkhan
Institute of Combustion Problems, Bogenbay Batyr St. 172, Almaty 050012, Kazakhstan
4 shared publications - Kaster Kamunur
Faculty of Chemistry and Chemical Technology, al-Farabi Kazakh National University, Almaty 050040, Kazakhstan
3 shared publications - Sergey M. Fomenko
Institute of Combustion Problems
3 shared publications - Abu Bakar Putra Ilhamsyah
Department of Applied Physics, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor, Malaysia
2 shared publications - Aigerim Sovet
Laboratory of SHS–New Materials, Institute of Combustion Problems, Bogenbay Batyr Street 172, Almaty 050012, Kazakhstan
2 shared publications
Latest Publications
- Open Access
Effect of Co3O4 Concentration on the Phase Composition, Microstructure, and Superconducting Transition of Nonstoichiometric YBa2Cu3O7−δ Ceramics
The effect of Co3O4 concentration on the phase composition, surface morphology, geometric density, estimated porosity, compressive strength, and resistive superconducting transition of YBa2Cu3O7−δ ceramics was comparatively investigated. Undoped YBa2Cu3O7−δ and Co3O4-modified YBa2Cu3O7−δ ceramics containing 0.1, 0.5, 1.0, and 1.5 wt.% Co3O4 were prepared from the same nonstoichiometric Y–Ba–Cu–O precursor mixture by a solid-state reaction route followed by oxygen annealing. Phase composition was evaluated by X ray diffraction, surface morphology by scanning electron microscopy, geometric density from specimen mass and dimensions, compressive strength by uniaxial compression, and superconducting transition parameters by four probe electrical resistance measurements. The YBa2Cu3O7−δ phase remained the dominant crystalline phase in all specimens. The sample containing 0.1 wt.% Co3O4 exhibited the highest YBa2Cu3O7−δ content among the modified specimens, 65.2 wt.%, the highest measured compressive strength of 1.95 MPa, and the highest onset transition temperature of 95 K. The highest geometric density of 5.36 g/cm−3 and the lowest estimated porosity of 15.3% were obtained at 0.5 wt.% Co3O4. The specimens containing 1.0 and 1.5 wt.% Co3O4 showed lower YBa2Cu3O7−δ phase fractions and lower geometric density, and did not reach the zero-resistance state within the available measurement range. Although the 0.1 wt.% specimen exhibited a higher onset temperature than undoped YBa2Cu3O7−δ, its lower zero-resistance temperature and broader transition indicate that Co3O4 did not improve all superconducting parameters simultaneously. Since only one specimen was tested for each composition, the density and compressive strength trends should be regarded as preliminary.
Open AccessEffect of Co3O4 Concentration on the Phase Composition, Microstructure, and Superconducting Transition of Nonstoichiometric YBa2Cu3O7−δ Ceramics
The effect of Co3O4 concentration on the phase composition, surface morphology, geometric density, estimated porosity, compressive strength, and resistive superconducting transition of YBa2Cu3O7−δ ceramics was comparatively investigated. Undoped YBa2Cu3O7−δ and Co3O4-modified YBa2Cu3O7−δ ceramics containing 0.1, 0.5, 1.0, and 1.5 wt.% Co3O4 were prepared from the same nonstoichiometric Y–Ba–Cu–O precursor mixture by a solid-state reaction route followed by oxygen annealing. Phase composition was evaluated by X ray diffraction, surface morphology by scanning electron microscopy, geometric density from specimen mass and dimensions, compressive strength by uniaxial compression, and superconducting transition parameters by four probe electrical resistance measurements. The YBa2Cu3O7−δ phase remained the dominant crystalline phase in all specimens. The sample containing 0.1 wt.% Co3O4 exhibited the highest YBa2Cu3O7−δ content among the modified specimens, 65.2 wt.%, the highest measured compressive strength of 1.95 MPa, and the highest onset transition temperature of 95 K. The highest geometric density of 5.36 g/cm−3 and the lowest estimated porosity of 15.3% were obtained at 0.5 wt.% Co3O4. The specimens containing 1.0 and 1.5 wt.% Co3O4 showed lower YBa2Cu3O7−δ phase fractions and lower geometric density, and did not reach the zero-resistance state within the available measurement range. Although the 0.1 wt.% specimen exhibited a higher onset temperature than undoped YBa2Cu3O7−δ, its lower zero-resistance temperature and broader transition indicate that Co3O4 did not improve all superconducting parameters simultaneously. Since only one specimen was tested for each composition, the density and compressive strength trends should be regarded as preliminary.
- Open Access
Open-Air SHS Toward Boron Carbide Formation: A Comparative Study of B2O3-Al-C and B2O3-Mg-C Systems
A comparative compositional screening of combustion behavior and phase formation during self-propagating high-temperature synthesis in B2O3–Al–C and B2O3–Mg–C mixtures was performed under the same open-air laboratory conditions. Twelve strongly carbon-rich formulations were examined. These formulations were not intended to reproduce the target stoichiometric reactions and are interpreted as an empirical screening matrix rather than as optimized stoichiometric compositions. In the individual SHS runs, the Mg-containing formulations produced higher recorded maximum apparent local combustion front temperatures and estimated apparent average front propagation velocities than the Al-containing formulations. Because each formulation was tested only once, these observations do not establish reproducible differences between the two systems. Qualitative X-ray diffraction analysis identified Al2O3, Al20B4O36, Al4B2O9, and residual Al in the aluminothermic products. MgO, Mg2B2O5, and Mg3B2O6 were identified in the magnesiothermic products. Weak reflections attributable to B4C were observed in selected compositions, whereas oxides and metal borates were the principal crystalline phases identified in both systems. This result indicates that the carbide-forming pathway was competitively disadvantaged under the investigated open-air SHS conditions. Thermodynamic calculations for the idealized reactions showed that the relative standard driving force depended on temperature and the phase states of the reactants and products. The final phase assemblages indicate competition between carbide formation and the formation of stable oxide and borate phases. Atmospheric oxidation may also have contributed to the oxide-rich products. The results provide a descriptive comparison of the two investigated formulation sets and identify compositional patterns associated with limited B4C formation under open-air SHS conditions.
Open AccessOpen-Air SHS Toward Boron Carbide Formation: A Comparative Study of B2O3-Al-C and B2O3-Mg-C Systems
A comparative compositional screening of combustion behavior and phase formation during self-propagating high-temperature synthesis in B2O3–Al–C and B2O3–Mg–C mixtures was performed under the same open-air laboratory conditions. Twelve strongly carbon-rich formulations were examined. These formulations were not intended to reproduce the target stoichiometric reactions and are interpreted as an empirical screening matrix rather than as optimized stoichiometric compositions. In the individual SHS runs, the Mg-containing formulations produced higher recorded maximum apparent local combustion front temperatures and estimated apparent average front propagation velocities than the Al-containing formulations. Because each formulation was tested only once, these observations do not establish reproducible differences between the two systems. Qualitative X-ray diffraction analysis identified Al2O3, Al20B4O36, Al4B2O9, and residual Al in the aluminothermic products. MgO, Mg2B2O5, and Mg3B2O6 were identified in the magnesiothermic products. Weak reflections attributable to B4C were observed in selected compositions, whereas oxides and metal borates were the principal crystalline phases identified in both systems. This result indicates that the carbide-forming pathway was competitively disadvantaged under the investigated open-air SHS conditions. Thermodynamic calculations for the idealized reactions showed that the relative standard driving force depended on temperature and the phase states of the reactants and products. The final phase assemblages indicate competition between carbide formation and the formation of stable oxide and borate phases. Atmospheric oxidation may also have contributed to the oxide-rich products. The results provide a descriptive comparison of the two investigated formulation sets and identify compositional patterns associated with limited B4C formation under open-air SHS conditions.
- Open Access
Radiation-Induced Defect Engineering in REBCO High-Temperature Superconductors: Defect Morphology, Vortex Pinning, and Technological Reliability
Radiation-induced defect engineering is an effective approach for modifying the vortex-pinning landscape in high-temperature superconductors, particularly REBCO-coated conductors and Bi-based cuprates. This review critically summarizes the relationship between irradiation parameters, defect morphology, and superconducting performance. The discussion covers point defects, defect clusters, columnar tracks, planar defects, and displacement cascades generated by electrons, gamma rays, light ions, heavy ions, and neutrons. Special attention is given to the dual role of irradiation: moderate defect concentrations can enhance the critical current density by introducing artificial pinning centers, whereas excessive disorder suppresses the superconducting transition temperature and degrades current transport. The review also discusses the relevance of irradiation effects for fusion magnets, space technologies, accelerator systems, and high-field applications. Finally, the review identifies key challenges for future HTS radiation engineering, including cryogenic in situ irradiation, coupled radiation–strain–field experiments, damage metrics beyond dpa, and multi-scale models capable of linking atomic defect production, oxygen disorder, vortex pinning, and macroscopic Jc/Tc degradation.
Open AccessRadiation-Induced Defect Engineering in REBCO High-Temperature Superconductors: Defect Morphology, Vortex Pinning, and Technological Reliability
Radiation-induced defect engineering is an effective approach for modifying the vortex-pinning landscape in high-temperature superconductors, particularly REBCO-coated conductors and Bi-based cuprates. This review critically summarizes the relationship between irradiation parameters, defect morphology, and superconducting performance. The discussion covers point defects, defect clusters, columnar tracks, planar defects, and displacement cascades generated by electrons, gamma rays, light ions, heavy ions, and neutrons. Special attention is given to the dual role of irradiation: moderate defect concentrations can enhance the critical current density by introducing artificial pinning centers, whereas excessive disorder suppresses the superconducting transition temperature and degrades current transport. The review also discusses the relevance of irradiation effects for fusion magnets, space technologies, accelerator systems, and high-field applications. Finally, the review identifies key challenges for future HTS radiation engineering, including cryogenic in situ irradiation, coupled radiation–strain–field experiments, damage metrics beyond dpa, and multi-scale models capable of linking atomic defect production, oxygen disorder, vortex pinning, and macroscopic Jc/Tc degradation.
- Open Access
- 23 June 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Processing optimization of mechanochemically activated YBCO powders with La₂O₃ micro-additives for PIT conductor fabrication
- 23 June 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Open AccessProcessing optimization of mechanochemically activated YBCO powders with La₂O₃ micro-additives for PIT conductor fabrication
- Open Access
Effect of Mechanical Activation on Spinel Transformation and Chromium Reduction from Ferroalloy Waste Under SHS Conditions
Chromium-containing ferroalloy wastes represent an important secondary resource; however, chromium is mainly bound in thermodynamically stable spinel phases, which complicates its reduction. Unlike previous studies focusing on pure oxide systems, this work demonstrates the enhanced destabilization and subsequent reduction of MgCr2O4 spinel in real ferroalloy wastes under SHS conditions, revealing a non-monotonic relationship between activation time and reduction efficiency. A critical activation threshold (~30 min) was identified, beyond which particle agglomeration suppresses reaction kinetics. Powder mixtures based on HShP and KEK wastes with Al–C–Si reducing agents were mechanically activated for 10–120 min and subsequently subjected to SHS at 950 °C. The combustion parameters, phase composition (XRD), microstructure (SEM), and elemental composition (EDS) were analyzed. The results show a pronounced non-monotonic dependence of combustion temperature and front velocity on activation time, with maximum values at ~30 min (1920 °C and 1.10 mm/s for HShP; 1765 °C and 0.98 mm/s for KEK). XRD analysis indicates that MgCr2O4 was not detected within the XRD detection limits and that the highest relative amount of metallic chromium phase (~8% for HShP and ~6.8% for KEK) was observed at the same activation time. SEM observations reveal the formation of a more dispersed and porous structure, while EDS indicates an increase in chromium content up to ~15 wt.% in local regions. At longer activation times, overgrinding and agglomeration reduce process efficiency. Mechanical activation enhances chromium reduction through improved mass transfer, with an optimal activation time of ~30 min. The chromium reduction efficiency was evaluated using a semi-quantitative approach based on XRD phase analysis and supported by EDS data, allowing comparative assessment of reduction efficiency rather than absolute extraction values. These results highlight the existence of a critical mechanochemical activation threshold governing the balance between enhanced reactivity and agglomeration effects.
Open AccessEffect of Mechanical Activation on Spinel Transformation and Chromium Reduction from Ferroalloy Waste Under SHS Conditions
Chromium-containing ferroalloy wastes represent an important secondary resource; however, chromium is mainly bound in thermodynamically stable spinel phases, which complicates its reduction. Unlike previous studies focusing on pure oxide systems, this work demonstrates the enhanced destabilization and subsequent reduction of MgCr2O4 spinel in real ferroalloy wastes under SHS conditions, revealing a non-monotonic relationship between activation time and reduction efficiency. A critical activation threshold (~30 min) was identified, beyond which particle agglomeration suppresses reaction kinetics. Powder mixtures based on HShP and KEK wastes with Al–C–Si reducing agents were mechanically activated for 10–120 min and subsequently subjected to SHS at 950 °C. The combustion parameters, phase composition (XRD), microstructure (SEM), and elemental composition (EDS) were analyzed. The results show a pronounced non-monotonic dependence of combustion temperature and front velocity on activation time, with maximum values at ~30 min (1920 °C and 1.10 mm/s for HShP; 1765 °C and 0.98 mm/s for KEK). XRD analysis indicates that MgCr2O4 was not detected within the XRD detection limits and that the highest relative amount of metallic chromium phase (~8% for HShP and ~6.8% for KEK) was observed at the same activation time. SEM observations reveal the formation of a more dispersed and porous structure, while EDS indicates an increase in chromium content up to ~15 wt.% in local regions. At longer activation times, overgrinding and agglomeration reduce process efficiency. Mechanical activation enhances chromium reduction through improved mass transfer, with an optimal activation time of ~30 min. The chromium reduction efficiency was evaluated using a semi-quantitative approach based on XRD phase analysis and supported by EDS data, allowing comparative assessment of reduction efficiency rather than absolute extraction values. These results highlight the existence of a critical mechanochemical activation threshold governing the balance between enhanced reactivity and agglomeration effects.
- Open Access
Research in the Commonwealth of Independent States on Superconducting Materials: Current State and Prospects
An overview of research on superconducting materials has been provided, including brief annotations of published papers and scientific cooperation among the Commonwealth of Independent States (CIS) countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan. It is shown that fundamental research on superconducting materials is being funded for development and study more at the government level in each republic than from private funds or organizations. One of the most promising materials, as indicated by recent studies, are those synthesized from metal hydrides, particularly lanthanum hydride, which exhibits superconducting properties at 203–253 K, close to room temperature. Unfortunately, this type of material’s practical application is currently limited because of the extremely high pressure necessary during exploitation. The most promising direction, as inferred from research conducted in CIS countries, is the development of cuprate superconductors doped with rare-earth elements such as yttrium, lanthanum, and other metals. There are also iron–nitrogen junctions, metallic and organic superconductors, and research into improving technologies for producing ultrathin substrates using laser or plasma deposition methods. CIS countries have established a strong scientific foundation in superconductivity, with Russia leading fundamental and experimental advances in high- and low-temperature superconducting materials. Future research will likely focus on improving synthesis techniques for ultrathin superconducting films and exploring novel doped hydride systems to achieve stable superconductivity near ambient temperatures.
Open AccessResearch in the Commonwealth of Independent States on Superconducting Materials: Current State and Prospects
An overview of research on superconducting materials has been provided, including brief annotations of published papers and scientific cooperation among the Commonwealth of Independent States (CIS) countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan. It is shown that fundamental research on superconducting materials is being funded for development and study more at the government level in each republic than from private funds or organizations. One of the most promising materials, as indicated by recent studies, are those synthesized from metal hydrides, particularly lanthanum hydride, which exhibits superconducting properties at 203–253 K, close to room temperature. Unfortunately, this type of material’s practical application is currently limited because of the extremely high pressure necessary during exploitation. The most promising direction, as inferred from research conducted in CIS countries, is the development of cuprate superconductors doped with rare-earth elements such as yttrium, lanthanum, and other metals. There are also iron–nitrogen junctions, metallic and organic superconductors, and research into improving technologies for producing ultrathin substrates using laser or plasma deposition methods. CIS countries have established a strong scientific foundation in superconductivity, with Russia leading fundamental and experimental advances in high- and low-temperature superconducting materials. Future research will likely focus on improving synthesis techniques for ultrathin superconducting films and exploring novel doped hydride systems to achieve stable superconductivity near ambient temperatures.